Freewing 64mm F-16 with afterburner
2 Video Views·Mar 27, 2026
AI Generated·May contain errors
Okay, the Freewing 64mm F-16. I haven't made a video of this yet.
And let's see here, we have afterburner in the rear. We got our afterburner hooked up,
which is 5280 RC. And I'm flying this on the SMC high voltage pack, which I don't charge
them up to the high voltage. I got a high voltage charger, but I don't use it after I heard
everybody talking about like, you ruin the cell life by going high voltage so many times. So I
just charge it at the normal 4.20 volts. So it's a 2400. That's where I have it and balance is
perfect. I took this out to Apollo Airfield last week. And I didn't do so good. I bounced it like
three times. And I completely snapped off the elevator control surface. And I still don't have
it perfect. What I did was I CA'd it or not CA, I used the China glue that comes with the plane,
not foam tack, but it's basically the same thing. Did a bead on the seam, stuck together,
pull it apart, let it dry for a minute, and then put it back together, held it there.
And it's rock solid. The only thing I did mess up on, I don't know if you can see, but
it's not perfectly aligned. But I don't think that's gonna make much difference.
It's just off by a smidge. But yeah, I got an afterburner in this. And let's get it up.
Hopefully, I got my camera in the right spot. So you can see. No sunglasses.
Show you the afterburner real quick.
I think on this flight, I'm going to... I have my gains for my AS3X halfway on the knob.
So I'm gonna see how that is. Maybe try increasing it all the way, see if it oscillates. I only have
it on the time one setting. I don't have it on times two. For my control surfaces, I'm at high
90 on the ailerons with 20% expo, 90 on the elevator, 30% expo. And that's why I bounced
last time out at Apollo Airfield. I started reducing expo, and I dropped my expo on my
elevator down to 20. And yeah, I had a hard time landing. I just bounced it.
Rudder's 100% with I think like half the expo. But all through my rates, high, low, and mid,
the rudder's 100%. And then on my mid rates, which I mostly keep the plane in when I'm flying,
I just use high rates to take off. But on the mid rates, I'm at 80 with 20% expo all the way around,
except the rudder. The rudder's 100%. All right, we're out here a little bit too far.
And on this 2400, I'm going to do two minutes, 40 seconds on the timer.
Hopefully we can see that. All right. High rates? High rates. All right, let's do it.
What a baby. Nice vertical. And she just floats. I got a little bit of wind to my back,
and I'll show you an approach. No safe, just AS3X. Just get her out there, get it in turn,
just kill the throttle. I got a little bit of wind, like I said, to my back.
You can see it pitching up. Let it sink. It's floating, floating. I pull up a little bit,
but yeah, she's a baby. Let's try sensitivity. I got the sensitivity turned all the way up on the
sink. She's twitching a little bit. I got the sensitivity turned all the way up on the AS3X.
Can't tell. Let's try it all the way down. There's no AS3X gains are all the way down.
Crank it back up. A little twitchy. Take it back to halfway. Here's halfway. Perfect.
Yeah, it's pretty good. Halfway. All right, so this flight went by quick. All right, here we go.
Let's land it. We'll just get her out there. I'm just completely dead stick.
Riding the wind, and then she'll start to sink. Completely dead stick. Flaring, flare, flare.
Beautiful. No safe, just AS3X. We got a little bit of wind. Oh man, it's a baby. Baby to land.
With that, taking my Expo to 30%. Actually, I'm in medium race right now. My control surfaces
are 80-20. That feels really good. I got plenty of elevator authority for landing.
That repair on the control surface of the elevator has made,
there's no significant difference in the way the plane handles.
All right, there's the F-16, and I will put this up in a little bit.

