Episode 106: The light in my Lionel caboose was dead, so I replaced it with LED tape lights, a 1 amp bridge rectifier, and a 4700 mf 25v capacitor. Now I have flicker-free, bright LED lights in my 45-year-old caboose!
Watch and learn how you can do it, too!
Chapters:
00:00 Introduction 00:30 Lionel MPC 6-9186 Conrail N5C Porthole Caboose 01:36 Flicker-Free vs. Regular Lighting 02:27 The Basic Circuit 04:45 What Capacitor Value To Use? 08:15 The Final Circuit On The Breadboard 09:03 Soldering The Components To The Copper Prototype Board 09:55 Wiring The Pickup Rollers 10:44 Circuit Board 2.0 12:38 Compare Upgraded Caboose To Originals 13:34 Running Around The Layout! 14:14 Final Thoughts
Hello again, this is Mike with Toy Train Tips and Tricks, and in the last episode we showed how to
use these LED tape lights to add light to structures, and so I'm going to take the
next logical step in this episode, and we are going to add some light to this Lionel caboose.
Now this was an MPC era N5C porthole caboose. Interestingly, it says built 176. Conrail didn't
exist in January of 76. It didn't exist until April of 76, so I think they kind of cheated
on the month there. This was available in late 76, but Conrail didn't exist and did not have
an established paint scheme yet in January of that year. So anyway, we've got this porthole
caboose that the original light bulb is gone, and even the wires originally came with it. They've
fallen off over the years. So rather than replace the original light bulb, which I checked online,
and just a replacement incandescent bulb for these is about five bucks,
so I've thought well let's just go ahead and replace it all. Let's upgrade it with LED lighting
and let's take the added step of uh let's let's make it flicker free. One of my pet peeves with
lighted cars and cabooses is as they go around the track they go across switches and crossovers
and the light goes on and off and on and off and I think if I were a miniature crewman on my O'Gage
railroad I would you know I'd be getting headaches and everything else and it's so annoying with the
light going on and off. So by adding just a few things to the circuit, mainly capacitors,
we're creating an anti-flicker. Now this is not the same thing as constant voltage,
constant intensity lights. For that you need a voltage regulator which is more expensive. We're
not doing that but we are going to add capacitors and that is going to make it so that you will see
some difference in light intensity just for that moment as it goes across the switch but the light
will not go out complete. First let's let's cover the basics here. We've got our feed coming from
the transformer and so I've got a little breadboard here where I can you know play around with
circuits and get them to work. And this first part is unnecessary for just lighting the car.
I do have a small bridge capacitor here, a one amp bridge capacitor, which is more than enough
to drive these six LEDs. Why six LEDs? Because it's the best that matches the length of the frame.
Nine is too long so six is about right. And so well is six LEDs bright enough? Well we'll take
the cab here and put it over. And here let me turn off my extra camera light here. And as you
can see, six bulbs is going to be bright enough for the caboose. And it's really brighter than
that. These bright LEDs that I'm using on my workbench are disguising it a little bit. That's
plenty of intensity to be seen on the layout. So the easy way is simply to replace. We would have
our wire coming from the center rail, our wire coming from the wiper giving us our center rail,
and our third rail. So we would have our hot and our common. Those would originally go to the light
bulb, which I've taken off. And so the simplest way would just be to take that,
use our little connector here, wire in the two wires from the roller connector,
and attach our strip. And if you need more details on how to do this, it's in my previous video.
And you're ready to go. You don't need anything else. Since I'm adding the anti-flicker circuitry,
I do need a bridge capacitor to turn the AC to DC because I'm a bridge capacitor bridge rectifier.
Thank you. The bridge rectifier to change the AC to DC because I'm using a capacitor to make the
lights not flicker. Okay. So here's what we have. We have our AC power coming from my transformer.
This would represent track power. And I've got it going into these two slots on the breadboard.
That power comes in here in this little bitty bridge rectifier here. And this side is the
input. So then we have a positive and a negative output, which are then, I've got them wired here
to this side to the positive and the negative here on the breadboard. Now, since these LEDs,
this LED strip runs on 12 volts, it's going to take quite a bit of capacitance power to keep
these lit. And I don't really have any big capacitors in my collection at the moment,
but before I go out to the local electronics store, I can test and see what value of capacitor I need.
Now, of course I could do the math on it, but I really want to see the results here. So by wiring
these capacitors in parallel across the circuit, I can add them up until I get the effect that I
want, which in this case, I have four 1000 microfarad and one 470 microfarad. So 4,470
microfarads. And what you're going to see is when I turn it on here, let me turn the spotlight off
here so you can see this even better. The most that I get is a slight dimming as the rollers go
across your switches and crossovers and such. So now I know to replace all of these in the
circuit, I'm going to get the next common value would be a 4700 microfarad capacitor. So one of
those will replace all five of these. And so again, so it goes from AC power to the bridge rectifier,
turns into DC, runs through the capacitor, and then out to my LED strip. And that's all there
is to it. Now, if I wanted to add marker lights, I'm going to use the regular plastic inserts here
for the marker lights. If I wanted to run LEDs, I would take these out and I could use another
terminal strip on this end of my LED strip. So I've got power coming in here,
power coming out here, and then I would need a resistor of appropriate value, depending on the
LEDs that I was using to reduce this 12 volt down to a value that the two LEDs that I would put on
my marker lights would work. So just be adding on to the tail end of the circuit here. And I would
do that because I've already rectified everything to DC. I wouldn't need anything else, just a
resistor going into my LEDs. And now we have replaced the five capacitors that totaled up to
4470 microfarads with one 4700 microfarad capacitor. This one is rated for 25 volts,
4700 microfarads, and the result is like so. We kill the power and you see it just flickers just
a little bit as I turn the volume on and off. It stays very, very, very constant. And then we turn
it off completely and it slowly fades out to zero. So now it's a matter of transferring this circuit
from my breadboard and soldering it together and installing it in the caboose. Now it's really sort
of overkill for this small circuit, but I am going to use this copper prototype board and solder the
pieces on here. And yes, I have a big magnifying glass because I am a blind old man with trifocals.
And so I'm trying to make this as big as possible so I can see what I'm doing here.
Okay, and you can see my less than stellar soldering job, but we have our power coming in
from the track goes to this side of the bridge rectifier. This side of the bridge rectifier comes
out and connects in with our capacitor and with our wires going to the lights.
And we've replaced the test leads with my official wires here and a quick smoke test.
And again, it works. So now I've got my circuit board together. I've run the wire going to
the pickups here through the frame and where I'm going to attach is easier. I take this axle off
to get access and the wire going to the center roller is going to attach right there and the
wire going to the outside rails is going to attach right there. And this part of the circuit is still
before it hits the bridge rectifier. So it doesn't matter which wire goes where. And now with wires
connected here, we put the axle back on and we're ready to mount board. Okay, so while I was
somewhat proud of my first attempt here, this is just looks nasty. It does work. But I just
couldn't take the look there. So I redid this. And like I said, I'm very proud. This is the
first one I did and it does work. So with what I learned from the first one in mind, I came back
and I hope you'll agree this is much nicer looking and hopefully, well, I know it. I've already
tested it. It works just fine. So same thing. I've got the wires coming in from the feeds.
They go here, which then ties into the bridge rectifier. Positive and negative come out,
go into my capacitor, which comes out and then goes into my light strip this way. Now,
instead of using this big hunk of styrofoam, first I laid down a layer of vinyl electrical tape
so that if one of these connections should somehow get down to the frame, it won't short
out against the metal of the frame. And then in order to create an air gap, I just used some of
this gorilla mounting putty and I put some in the corners and pressed it down and we have a nice
firm seal. And so it is ready to put back together and it works fine. So instead of this big hunk
of styrofoam and everything, this looks much nicer and I'm going to repurpose this one in
another spot on the layout. But here we go. The finished product looks much nicer and with the
experience I gained from the first one, this took me about 20 minutes to put together with all the
solder joints. I'm still not the world's best solderer, but I am getting better. So there it is.
So here you see the finished product, our Conrail Caboose with upgraded LED lighting
with a non-flickering circuit compared to an original Lionel MPC, same era, but with the
original light bulb. And then also a similar era Lionel Searchlight car, again with the original
bulb. And so you can see a big difference not only in the intensity of light, this is about half
throttle, but as the train runs around the layout you will notice a lot of difference in the amount
of flickering. Here let me take the camera light off so you can see better the intensity difference.
And these LEDs are also available in a soft white which is more of a yellow compared to this if you
this color better. And so here we go with a train.
So there it is, a modified anti-flicker LED lighted caboose, total parts less than the cost
of replacing the original light bulb, and pretty easy to do even for someone like me who is a
novice in electronics. So hopefully you'll like this and maybe give this a try in some of the
projects on your layout. And so I hope you like the video and if you do, please click on like,
please share it, please subscribe, hit that notifications bell, tell your friends,
tell your neighbors, and most importantly, until next time, keep the trains running!