Episode 108: How to replace the lights in Lionel's MPC-era "Baby Madison" passenger cars with flicker-free LEDs. This is an easy, inexpensive project that can be completed by anyone with a basic knowledge of electronics (like myself).
This project uses LED tape lights, a 1 amp bridge rectifier, a 4700 microfarad 35 v electrolytic capacitor, a copper prototype board, and some wire and (optional) mounting putty.
Chapters: 00:00 Introduction to Lionel MPC "Baby Madison" Passenger Cars 02:08 How To Disassemble The Baby Madison Cars 09:02 Removing The Old Bulbs 09:35 Replacing A Faulty Pickup Roller 15:44 Preparing The Circuit Board 21:00 Installing The LED Strip 22:09 Testing The Final Product 23:50 Running On The Layout
Hello again, this is Mike with Toy Train Tips and Tricks.
And today we are looking at these Baby Madison cars produced by Lionel MPC in the 70s, in
this case cars from the Crescent Limited.
But these Baby Madisons, these smaller heavy weight passenger cars, include road names
such as B&O, Milwaukee Road, Pennsylvania, Southern Crescent, Blue Comet, Alton Limited,
Chessie Seems Special, and others.
And this was a neat innovation that MPC made in the 1970s, making a decent looking heavy
weight passenger car that was smaller than the post-war cars so that it would negotiate
027 track easily, but at the same time not look ridiculously small, like the 027 Streamliners,
in my opinion, look way too small.
So these were nice cars, and they made some changes along the way in couplers, in trucks,
but for the most part these are pretty similar cars.
In my case, after 40 plus years, it's time to get in and revamp them a little bit, and
the main thing being the lighting.
Many of my cars, the bulbs have burned out completely, or, in the case of this, as you
can see, the car on the right, the lighting has become extremely dim over the years, and
so I'm going to replace this incandescent lighting with LEDs, and I'm going to put flicker-free
lighting in at the same time, so as the cars go around the layout, cross over turnouts
and crossings, and sometimes even dirty track, the lights won't flicker on and off, and the
passengers will be happier not having the headaches from the lights coming on and off.
So let's follow along as we go step-by-step through how to disassemble these cars and
install the new lighting.
Okay, so I've got my observation car here, and again, these baby Madisons, they're about
an inch and a half shorter than the post-war heavyweight passenger cars, which again allows
them to go around 0.27 curves.
They are not true O-scale, they're right around 1.64, actually.
These cars look really good with, say, a Marks E-7, which is a 1.64 approximate model.
So they don't look good with the true 1.48 Lionel items, like F3s are too big, but some
of the mid-to-small sized steamers, like the 442 that some of the sets came with, and
the 464 Hudsons that came with the sets, look really sharp with these.
A true scale Hudson would be way too big for these.
As these progressed through the years, the earliest models came with non-operating couplers.
Then by the time we get to the Southern Crescent, we've got plastic trucks with operating couplers.
Following this, the next one, the Blue Comet, came with six-wheel trucks with metal side
frames, and they are not compatible.
You can't say, well, I'll just get some six-wheel trucks and put them in the four-wheel.
They won't mount the same, and you would have to make extensive modifications to the underframe
in order to make room for the six-wheel trucks.
So it's not really an easy switch, like you might think.
Okay, the biggest challenge to working on these cars is getting them disassembled.
These cars use a no-screw assembly, and in fact, the roof portions are integral with
the windows, and it actually locks into the floor to keep anyone from getting it apart.
So how do you get it apart?
Well, the key is, if you look up here to the ventilators, find a ventilator in the next
window to the inside, whether it is here, or whether it is here, and similar on the
other side.
These are the tabs where the windows lock into the floor.
And this is designed, this is a little thicker, and it's designed that you can push in on
the window, and then at the same time, try to separate along this seam between the side
of the car and the roof.
So Lionel recommends a metal ruler for this.
I have found that even better is the flat side of a brand new hacksaw blade.
Don't use the toothed side, but the flat side of a hacksaw blade is really thin.
And I also, I made this little template to help me a little bit, but I don't know how
necessary it is, but I use this, I line that up on the window, and I push down, and then
at the same time as I push in on the tab, I try to wedge this into my seam very carefully.
Oh, I heard a click.
Okay, I've got a little bit of room there.
Let's move to the next window.
Let's try this other side.
And again, find your ventilator, the next window inside is this one right here.
And I'm going to push down right there while I find my seam.
Where'd my seam go?
I think I just popped it back in on the other side.
There we go, it's starting to separate.
And you just slowly work your way around until you get this to where it will pop out.
Okay, this one is being particularly stubborn, and so I've got it started with the hacksaw blade.
And you can see the separation here, and I'm working it here with some small screwdrivers.
I haven't found any one particular method being better than others.
Some of them are very easy to pop open, and some are more stubborn like this one.
Okay, now I finally have all four tabs at least loose for both sides, and it should
start to come apart easier at this point.
Keep pushing in on the tab while you wiggle.
There it comes.
And do that same thing at this end.
Keep pushing in on the window tabs while we wiggle.
Ha ha! And finally it will break loose.
So, when it does finally come loose, here's what you see.
So here's the tabs that were holding it in place here and here.
These two are just decorative.
This would be like the lavatory end of the car, although you see it on both sides.
So these tabs, and then these go into the snots in the floor.
Now, there's a high-tech method that they used to try to make it so that the light wouldn't shine so brightly
that you'd be able to see it through the roof, and that is cardboard.
So actually, I'm going to pull this out because when I reinstall my lights,
I'm actually going to attach it to this cardboard strip.
And in this case, the strip had dropped down some, and so light was only kind of getting out half the windows.
So I'm going to pull this out, and I'm going to put some tacky adhesive,
some of the Gorilla mounting tack on the backside to make sure this stays solid to the roof.
And then when I run my LEDs, they will run across this cardboard right here.
So there it is, state-of-the-art 1970s technology cardboard.
And you can even see the part number, 009500026.
Yes, this had a specific part in the Lionel Parts catalog.
And speaking of high-tech, you see some of our wires are held down by high-tech Scotch tape.
Well, I guess it held on for 40 years, so that's something, but yeah.
So we have our red and our white wires that come from our pickup underneath from here.
And in this case, there's actually one on each side, which is unusual to have the hot on one side and the ground on the other.
Most of them used as one integral truck.
So it's interesting why on this car, we have some on both sides.
Not quite sure why they did that.
Okay, so I don't plan on reusing these bulbs, so I'm going to save as much of the wire as I can here.
Let's cut this short.
Same thing on the other side.
Okay, so I still have my wires.
Okay, and in inspecting my rollers, got some bad news here.
And that is right here.
I don't know if you can see it on camera, but there's a big gouge in the roller.
Apparently, at one point, it wasn't rolling freely.
It was just being dragged across the center rail, and it dug a nice little groove right there in the roller.
So this is going to have to be replaced.
So I've got a replacement roller set here.
That means I'm going to have to be redoing the wiring as well.
So I haven't decided yet, I have to think about this, whether I just want to replace both of these with one
or keep this second one as a second ground.
Not sure.
But in any case, I need to remove this to get it ready for this.
So I'm going to try to keep everything as intact as possible in case I can salvage some of this for parts.
Keeping in mind that this is 40-year-old plastic, and basically you peel this back and it goes into slots in here.
Just to make things as low-stress as possible to try to keep things from breaking,
I'm going to pull the wheels out first.
And I'm just going to take my flat-headed screwdriver, and again, try not to put so much stress on it that it'll break.
There it comes.
One axle out, two axles out. That one was much easier.
I'll take this one to show you. There are two little fingers on either side, and they pop into little holes on the truck itself.
So it needs to be pulled out, again, a significant amount, but try not to break the tabs off.
Hey, we got it intact. Good.
So this one might be able to be salvaged and reused at some point.
And actually, on second check, instead of replacing it with a whole new setup,
I've got a spare roller in my junk box, and so I'm just going to swap out the new roller for the old roller.
So the first step is to get the old roller out.
So you see there's these little tabs. One goes down, two go up, and they just link into our copper piece here.
So I should be able to just pop that puppy right out, and there it is.
And so that's the bad roller, and let's replace it with the good roller.
Push it in, get the up tab right there. Now you see how loose that is.
That kind of works, but I like to make these a little bit more secure,
so I'm actually going to put a little dab of solder here and here to get these to hang together a little bit,
and then I like to bend the copper down, and that makes these rollers a little more secure so they don't fall out.
Okay, now I've got a little bit of solder on the contact and a little bit of solder on the roller,
and I'm going to assemble them.
Woo-hoo, hot, hot.
And then I'm going to hold the soldering iron on them to try to let some of this solder connect together
to make this a little better connection, both electrically and mechanically.
That goes in there. There we go, get the hook to go in the slot right there.
Then I'm going to push this down and see if I can't get the solder to make good contact between them.
All right, so now at this point I've decided I'm going to leave this one in place rather than risk breaking one,
and so since my solder joint is already here and it's in good shape,
we just need to reassemble this back into...
I'll go ahead and drop the wire in there while I'm at it.
Just reassemble this back into the truck.
Find my slots on this side.
Good.
Give it a little encouragement on this side.
Okay, and now we put our axles back on.
That's one side.
Get it lined up.
Give it some encouragement.
Oh, that side went in real easy.
Okay, and push.
There we go.
Wheels are turning.
Okay, so our pickups are fixed.
All right, I'm going to try to use the existing pickup wires here,
which means I need to strip just a little bit off the edge of each one.
There we go. Okay.
All right, so this is all set.
Now we are going to do our electrical work.
Now, my prototype boards are 5 by 7 millimeters,
and that 5 millimeters is just a little bit too wide.
It'll fit in the car by itself,
but when we take into account the window glazing and such,
it becomes a little bit too wide.
So I'm just going to take a little bit off of this side,
about two and a half rows here,
and just snip this off with nippers to make the board a little bit smaller.
Anyway.
Okay, so that fits much better.
Now, on some of these, I've put the board
and the lighting hanging from the roof.
This one, I'm going to put the board in the floor
and then run the wires up to the ceiling.
So in order to clear this little protrusion here,
I'm going to cut a little bit more off of my board,
because, again, I don't need all of these contacts.
So I'm going to trim it down just a little bit more
so that it will lay on the floor
and still clear these two little tabs.
Let me test fit.
And yes, it will drop right down onto the floor right there.
That's good. Okay.
Now, the next thing I need to do
is I need to solder on some contacts
that my feeder wires are going to attach to.
And as with most things,
there's certainly more than one way to skin a cat, as they say,
and there's more than one way to do these circuit boards.
Okay, here's my joint.
Heat. Solder. Heat.
Whoo, smoke.
The next part of my circuit is this small bridge rectifier.
It's going to turn my AC into DC.
And so I've got my feeders will come in here.
They're going to connect underneath.
And this side, in very small print, is just two wavy lines.
That's my AC, and then it'll go out with a positive and a negative.
This will be DC output on this side going to my capacitor.
Now, this part is very important.
We have positive and negative coming out on the bridge rectifier.
We need to make sure that the negative side of the capacitor
goes to the negative side of the bridge rectifier
and vice versa, positive to positive.
The longer lead is also positive.
So the stripe is on negative, the longer lead is on positive,
and that's how you know the difference.
Then lastly, these two wires connect the circuit board
to the LEDs that will be mounted on the car roof.
Okay, so here comes a tricky part.
I want to attach my pickup wires to my board.
I don't want to do it with the board mounted in the car
because I don't want the soldering heat anywhere near the plastic of the car.
So it's going to be a little bit of a stretch to do this,
but we'll get it done.
And I have these Gorilla mounting tabs underneath the board.
I'm going to just attach that to the floor of the car.
All right, so I have my pickups going to my circuit board,
turning the AC into DC so I can use the capacitor.
That will be my anti-flicker.
The output goes to these two wires,
which are going to go to my LEDs,
which are in the top of the roof of the car.
My strip of 12 LEDs.
And then to make the connection,
you can solder onto these fine points,
but I have these connectors here which do a much nicer job with it.
One side accepts your wires,
and the other side the LED strip slides into,
and you're ready to go.
So I'm going to mount this to this part of the cardboard here,
and then when my strips go in,
we'll have the proper length for the LEDs.
And we're going to take our LED strip.
Now, pay close attention up here,
which side is marked positive and negative.
That's going to make a difference which wire goes on which side.
We're going to put the positive on the top,
and I'm going to peel my adhesive off.
I'm going to peel my adhesive off.
There we go.
And we're going to put,
slide this into our contacts as far as we can.
Close it,
and put all of my adhesive down right there in the middle of the roof,
and then we'll sit that there and let that continue to dry,
and we'll be back in a few minutes.
And now we are ready for reassembling.
First we're going to just test fit everything,
and then we're going to check the power
just to make sure before we make the final push to put it back together.
So sitting it like this,
let's go take it over to track power and see what happens.
And now the moment of truth.
Nice, just like the one I did before,
this one is set and ready to go.
Now, if you don't like the brightness, you have a couple of options.
One is these LEDs are available in a soft white.
This is the bright white.
So if you don't like that effect, you want it closer to the original effect,
you can get the yellower version, which is the soft white.
Another option, you can kill the power a bit by adding a resistor
between the circuit board and the LEDs,
and so that would keep your power at a lower level maxing it out.
I don't seem to mind that.
And again, we've got the anti-flicker isn't as pronounced
as it was on the caboose project
because we have twice as many LEDs with the same size capacitor,
still the 4700 microfarad capacitor.
So the voltage difference will be noticed quicker,
but still, as I go up and down here on the transformer,
you really don't notice it very much.
And so if there's just a momentary interruption of power,
again, instead of going completely dark,
your passengers would just have a momentary interruption of,
you know, just a momentary dimming rather than completely going out.
And again, you see how far it goes to wind all the way down to nothing.
All right, so let's slide it in place and call this a car.
Well, let's turn out the lights
and see what our new passenger operations look like in the dark.
And in case you're wondering the difference,
this car, the one on the right, is the one I did first.
And with this one, the circuit board is on the floor,
actually over here.
And you can see that the lights with the circuit board
and the wires cast shadows.
So that is why for my second one, I put the lights from the roof down
so that even though there are things that are there,
the light comes in around and it doesn't cast shadows on the window.
So this one I'll be taking apart and redoing.
So definitely the light on the roof is the better idea
than the light on the bottom.
So in any case, there it is.
This is how to add your flicker-resistant lighting
to these Lionel Baby Madisons of the 1970s
using tape lights, a bridge rectifier, a capacitor,
and just a little bit of time and some wiring.
And you can rejuvenate your fleet of passenger cars as well.
So as always, I hope you like the video.
If you do, please click that like, click that share,
subscribe, tell your friends, tell your neighbors.
And until next time, keep those trains running.
♪