Episode 113: It's time to lay track on the new layout! I prefer working with traditional O27 profile tubular track. Watch to see why, and what tools and techniques you can use to have success with this type of track.
Chapters:
00:00 Introduction 00:30 O vs O27 Tubular 02:00 Tubular vs Modern Track 02:50 Cutting O27 Track 06:15 About Track Pins 10:03 Check Your Geometry 10:25 Track Screws 10:55 Finale
Toy Train Tips And Tricks is a channel devoted to the operation, repair, history, and collecting of classic 3-rail O and O27 gauge trains made by Lionel, Marx, K-Line, Menards, and other manufacturers.
And hello again, this is Mike with Toy Train Tips and Tricks, and today we are making a mess. Well,
yes, we're making a mess, but we are also, this is the exciting part, we are laying track
on the layout for the first time here. This is a good opportunity to show the types of track that
I use and some of the tricks that I use with working with it. And so in my case, I like to
use tubular track, specifically 027 tubular track. Now the main differences between 027 and your
regular O, in addition to the differences in track radii, which both are available in different track
diameters, but also the height of the rails. You see here the standard O is a little taller than
your 027. The track pins are a little bigger diameter on the O versus the 027. And you know,
so the O, it's taller, the track ties are taller as well. So if I were starting fresh today,
I would probably go with the O tubular, mainly because it's still in production,
still made by Menards. I believe Williams also is still making O tubular track, whereas 027
hasn't been made in about 20 years now. But 027 is still readily available. There's lots of it.
It was made for 80 some years, and I've been collecting it in, you know, my different train
sets and different layouts for 50 plus years. So I've got lots of it. So for me, it is cheap and
readily available. And for more information about the differences between O and 027 tubular tracks,
you can take a look at the video right up here. And it goes more in depth about the differences
between O and 027 tubular. Another reason that I like to use tubular track versus the modern
molded plastic roadbed type tracks, the real tracks or fast tracks and such, is that it's
easy to modify the tubular track to different track configurations. As you put the geometry
together, you will find from time to time that you need to make a custom section. And it is
much easier to custom cut these three rail sections than it is to modify all of the roadbed
as well. It can be done, but I find it much easier to modify the three rail track. So in this
case, I needed half of an 042 curve and also a partial straight. And yes, this is one of my
painted sections. That's not rust, that's paint. So I've marked off the spots of my cut with some
tape. So I have a good mark to deal with. And then as far as actually cutting the track, you can use
whatever method, whatever tools you want for cutting metal, whether that be a good old hacksaw,
a Dremel, a chop saw, if you have one, or any method that you would like as long as you can
cut through the metal. In this case, I'm going to use a hacksaw because I want a very precise cut
in a very specific location. But sometimes they don't have to be quite as precise and something
sloppier like a Dremel or a hacksaw. Dremel, because with the body of the tool itself,
it's hard to make a complete vertical cut. You end up having to angle it somewhat because the
body of the Dremel gets in the way. If you have one of the extension cables with a thinner head,
that works even better with the Dremel. So anyway, I'm going to cut these and show you what I do next.
So here I have my cut piece. Actually, you can see the vibration from the saw actually
helped take some of the paint off. And you can see the shiny rails underneath. When the sections
are made at the factory, the end that accepts the pins is spread a little wider to accept the pins
than you see here in the middle. Our hole is narrower. So I'm going to have to open this up a
bit in order to accept track pins. So use a tool like an awl or any pointed metal object,
a nail would work. I'm going to push this into each of the holes and I can line it up here with my
old eyes and push and twist. And you see that's making the diameter of the hole here. If I can
get it in focus. Focus. It's making the diameter of the hole a little bigger and cleaning up any
of the burrs left over from sawing in the process. There we go. And one more. And now focus. There we
go. And now we are ready to accept track pins in this piece of track. After my new pins are inserted,
I use my favorite tool for working with this tubular track. These are end nippers and if you
notice the way these pliers are designed with the hole in the middle, I can reach around the top of
the rail and squeeze here and tighten up these connections. So I've put my new track pins in.
I'm going to give them each a little squeeze to seat them in place, both for a better mechanical
connection and also a better electrical connection. Give it a little squeeze, help seat it in place.
And so these are a really cool tool. I found this at Harbor Freight. It was like
four dollars or so and it's a really invaluable tool for working with this tubular track.
Okay, so again, I'm dealing with 027 track and I'm using different manufacturers,
different eras. I'm mixing Marks, Lionel, K-Line, Postwar, MPC, Modern, and for the most part,
these pieces of track are interchangeable. Marks track pins are a little bit longer and a little
bit thicker than the Lionel and K-Line. They also lack the little groove that is here.
But with a little encouragement, the Marks rail joiners will go into Lionel and K-Line track and
the smaller Lionel K-Line will go into Marks, although you'll want to crimp down the ends to
make a snug connection. Speaking of which, my favorite track tool for that is if you have a loose
connection, take these end crimpers, put it over the edge and just crimp down and get that tight
around the rail joiner. You'll also want to make sure as you're doing this, your rail joiners,
you want to make sure they're nice and shiny. If there's any corrosion or any rust,
you hit it with some sandpaper and maybe some electrical cleaner to make sure you get a good
contact and no recurrence of the rust. You'll also want to think ahead about where you need to use
insulated track pins. For example, the inside of any of the remote automatic
non-derailing turnouts, you'll want insulated pins on the inside rails. For most of them,
an exception would be the very first 1954 versions of Lionel's 027 turnouts here. Lionel's
come in black plastic, K-Line's come in white plastic, or you can make your own. I print mine
on a 3D printer. Also in a pinch, round wood toothpicks I've successfully used for insulated
track sections. So you'll want those not only for your automatic switches, but also anywhere
where you're going to separate the track blocks. Think ahead electrically of where you might want
to stop your trains and make sure that you put insulated track pins in the center. Do it at this
point while you're doing your track planning and it will be easier later. You won't have to take
up a track to put down those insulated pins. You will often find in making a layout that you will
need to rearrange how the track pins are oriented. So if you need to remove a track pin, some of them
will come out pretty easy and I'll come use my rail nippers again and I'll grab on to the end and
give it a pull. If it doesn't come out easily, like this one is being a little snug, then take a
flat-headed screwdriver on the back side, slide it in and wiggle a little bit to widen.
You're crimping a little bit and then give it a pull and it comes right out.
Then to put it back in, we'll put the rail joiner in and then again take our end nippers
right around here and crimp it back together. So again you have a nice tight connection
like so. If you get a rail where the ends are bent out of shape, take your metal awl
and ream it out back to round and check it and that will help you put the rail joiners in and
reshape the rail into its proper contour. O27 rail joints are very forgiving both in and out
and side to side. This is both a blessing in that it makes it so you don't have to be super precise
in your track alignment, but also a curse in that if you're not careful, your geometry can
get way out of whack and create some kinks that shouldn't be there otherwise. So always double
check your track geometry and don't be afraid to cut sections to length for your particular
application. For securing the track to the table, I used number four by three quarter inch wood
screws. If I were using plywood as my base, I could probably get by by a number four by half inch
but since I'm using MDF board because it was cheap and available, I want something a little
bit longer to give it a bite into that particle board foundation and just simply drill into the
existing holes in the track ties. And so there it is, my methods for getting excellent results with
O27 sectional track with line L, K-line, marks, doesn't matter the manufacturer, you can mix and
match, but using this O27 profile tubular track to make my layouts. And most of these tips can be
used with standard O profile track as well. So if you're going the tubular route, I hope these
particular tips and tricks help you with your layout as well. Next time we are going to start
wiring up the layout and get some trains running. So until next time, this is Mike signing off with
Toy Train Tips and Tricks and until then, keep the trains running or if you're building your layout,
get those trains running soon. Catch you next time!