Episode 122: I rescued and restored this Lionel Quicksilver Express passenger train for less than $50!
First, I found the cars and dummy ALCO FA diesel in a "junk box" under a dealer table at a local train show. I took it home for $25.
Then, I bought a Postwar Texas Special FA (and a small Lionel transformer) from eBay for $19!
I cleaned the entire set, swapped the motor from the Postwar FA into the MPC dummy, replaced a few light bulbs, resoldered a wire, 3D printed two new couplers and...voila! My new-to-me passenger set!
Toy Train Tips And Tricks is a channel devoted to the operation, repair, history, and collecting of classic 3-rail O and O27 gauge trains made by Lionel, Marx, K-Line, Menards, and other manufacturers.
From trash to treasure, how I made this passenger set for less than $50, on this episode of Toy
Train Tips and Tricks. Hello again, this is Mike with Toy Train Tips and Tricks. If you've checked
out any of the manufacturer's catalogs lately, new stuff from Lionel or MTH, you see that even
basic starter sets are now, you know, $250, $300 and more even for a basic starter set.
Well, if you look hard enough, there are still good bargains that can be found on the secondary
market. So I was looking to add an inexpensive passenger train to my layout. And so my first
stop was a local train show about a month ago. And looking through the dealer tables and check
out the items that are underneath the tables at the shows. This is generally where the bargains
can be found. Things that need some work, that aren't nice enough to put up on the table, but
the dealers are taking them around. Anyway, maybe they can find somebody who's a buyer. Well, they
found me. And so I found this Quicksilver Express set. This was a MPC-era set. And originally,
it came with a powered FA, the dummy FA, and the three passenger cars. Now, I was really just
looking for the three passenger cars. I was looking for something that I could repaint.
Really didn't want the FA. But, you know, thinking about it, I didn't want to, you know, leave the
dealer stuck with an orphan FA that didn't match anything. It was going to take him forever to get
rid of it. So we threw that in. And so for the complete set, the FA and the three passenger cars,
we came to a price of a whopping $25. Can't beat that. Now, obviously, these cars are not in perfect
condition. But, you know, for the price, you know, you can't beat that. And then with my FA,
it's dummy, I figured, well, I could come up with something for it. And initially, I was going to
repaint everything. But actually, as I look at it, the more I see it, I'm kind of taken by the
graphics. It's like, yeah, I think I'm going to leave it for a while. So my thought was, well,
let's find some power for this set. Now, noticing that the dummy here does not have an E-unit slot
at the top. So that meant if I was going to find a powered chassis to fit this shell, I've really
got two options. Option one is one of the more modern FAs that have the electronic reverse unit.
The other option is there were post-war FAs that had no reverse unit at all, and therefore no
lever to stick out. Now, these were the bottom-of-the-line bargain barrel Lionel sets
of the late post-war period. You know, these are stripped-down models that were for mass marketers
to make them as cheap as possible. And after, actually, a few weeks of hunting on eBay,
I found one in a price that I was willing to pay. And that is this one right here,
this number 1055 Texas Special. Now, there are some other Texas Special FAs that are better than
this one. Again, this was bargain basement. It has no magnet traction, no traction tire,
no reverse unit, no horn. The only thing it has is a headlight, and it runs in forward only. So,
I have a $25 passenger train and a $20 powered diesel. So here we go. For under $50, I'm going
to have the basics of a passenger train. Now, I'm going to clean this up. I'm going to do some
modifications to it. But still, you can see that for not a whole lot of outlay of money, you can
have a fun set. So, let's dig in. So, let's start with our Texas Special here. And we're going to
take the shell off because we're going to swap shells with the Quicksilver Express. And these
are very simple. The assembly, you've got one screw in the back and a tab in the front, and
shell comes right off. I've got my Phillips screwdriver. I'm going to take off this Phillips
screw right here and pop the shell off. And here is my chassis. So, it's dirty and the light bulb
does not work. So, I'm going to replace the light bulb, clean up the wheels, clean up the chassis,
get... Okay, and I just happen to have a light bulb that would fit in my junk box. This is a
number 51 automotive indicator panel bulb. And it fits right here in the bayonet mount and it
works just fine. Next, I just took a slightly damp rag, cleaned off all the dust and muck,
and there was a little bit of oil and such. But it's pretty much ready to go clean now.
So, my MPC aeroshell, it goes exactly the same way. Attached, I've got one Phillips screw back
here and a slot in the front, and we are ready to go. So, now that I've got this shell off, you can
see all the dirt and muck and everything on here. I'm going to take this, I'm going to give it a
little bath in some lukewarm water, just a little dab of dish soap and a rag, and we are going to
clean this up a little bit before we put it on its new chassis. And there we go, 40 years of
gunk and grime removed with a little bit of dish soap and a cotton cloth, some lukewarm water.
You don't want to scrub too hard, especially on this silver. Silver paint traditionally is very
fragile. We are nice and clean and we are ready to put this on the powered shell. Now, the differences
between the modern plastic and the post-war Bakelite is that the Bakelite is a little thicker,
so you may need to take these mounting brackets right here on the side that help hold the shell
in place, and you may need to spread these out a little bit with a pair of pliers. We're going to
check it and see. If it's a little loose, we'll come back in and widen those. And yeah, you see
we're wiggling a little bit, so I'm going to widen these just a smidge. Let's try that.
There we go. That's a nice tight fit. Put our screw back in and we're ready to roll.
One powered unit with a new headlight, functioning rear coupler. Now, I haven't decided what I'm
going to do with this other chassis and this other shell, but just now for storage, I'm going to go
ahead and put this back on here. There we go. And let's give it the smoke test. Okay, it works.
Let's look at the passenger cars. Okay, so step one with the passenger cars is I'm going to
disassemble the the cars so I can clean them and I can see what's going on on the inside.
Now, the post-war versions of these streamlined cars had screws in the top that looked kind of
like... they had nuts on the top, so it looked kind of like roof ventilators, and that's how
the cars came apart. The MPC versions, instead of from the top, we have these holes where
they are screwed together way down there, so you're going to need a long-handled Phillips
screwdriver to get down in there and take these puppies apart. Okay, and voila! All right, so now
we're apart. We can see what's going on here, and this light bulb has come completely out of its
socket, and our window strip is off, and it needs some good cleaning. I think I'm going to try to
use the original wiring rather than upgrading to LEDs at this point. I'll try it like that and
see, but the first step, obviously, is going to be cleaning them up. So I'm going to disassemble
the other two as well, and we're going to take them apart. We're going to clean them like we did the
diesel, and we'll go from there. Okay, so after disassembling and taking a look, it turns out
all six of the original light bulbs do work. You do need to clean and reattach the window inserts,
and then so the only other repairs are going to be underneath as far as couplers. As you can see,
we are missing a coupler completely here on the observation car, and the dome car, we have a
coupler with a bad arm on it. I'm probably just going to seal that up with a rubber band, because
again, this is a passenger train. I'm not going to be really doing a lot of switching with this,
moving it back and forth. So if the couplers are not functional, that's not such a bad thing.
So as I was working with the cars, I actually found that I needed to replace not one, but
actually two couplers, and I also made the discovery of why I was not able to find these
parts in my schematic. In my earlier MPC cars, I have a Southern Crescent Baby Madison set, which
has a similar coupler, similar but not exact. On those, this piece has a hole here in the middle,
and the stud here on the coupler is a little bit longer, so that you can put the coupler on,
the stud pokes through, and then it pokes through the hole, and you push it on, and that's what
holds it in place. Now this design is different. These are designed not to be individual parts,
but once you put it on there, it was essentially heat welded together as a single part,
so that the entire truck, coupler and all, was one part, which is why I can't find individual parts
in any schematic for these. So that presents a new problem for a replacement coupler.
Essentially that I can't use this particular system, I had to come up with something else.
So the options were to totally replace the truck and all, which can be done, but as I mentioned,
these trucks, to find them on the secondary market, you're talking $15 to $20 per truck,
and really you need to buy a pair, because if you're replacing, you know, these with, say,
post-war trucks, they roll at different rates, so in order to get the car to roll right, you really
need to replace both trucks at the same time. So now you're investing $40, $45, $50 just in trucks
for a car that I bought for $5 at the show. I got a great bargain, yes, but still, you see,
the economy doesn't really work. The next option would be to remove the truck, which means taking
out the truck rivet and running, drilling a hole through here, running some type of a small bolt
and bolting the coupler on, which can be done, it's less expensive, but you go through the
trouble of popping off the rivet and then re-riveting it, which I can do, but for me,
it's a lot of work, a lot more work than the method that I used, which was using my Creality
Ender 3 to print new parts. So using an original coupler as a guide, I used my calipers to get the
dimensions, the width, the length, this little piece here. Now this is a dummy coupler that I'm
putting on, but again, these are passenger cars. I'm not going to be switching a lot with these.
And plus, if you put a dummy coupler with a working coupler, you know, at each end, as you
turn them around, you still have operation. Using my Ender 3, taking the dimensions, I came up with
this. Now the coupler head I had already designed for my caboose project that I did about a year
and a half ago, so I just needed to design a new shaft and put that on the design. So I came up with
this, and it fits right here into the coupler post. So now I need a method to connect it. So I came
up with another idea, which was to come up with a bracket that fits around the top, I'm sorry,
around the top of the coupler in this little slot, and these little arms grab on to this
protrusion here on the trucks. So you take your coupler and you put it on here the proper way.
Make sure you've got your knuckle in the right orientation so you don't have to do it twice.
And then I'm going to take this clip and I'm going to slide it on here. Actually, I found
that it's easier to do it like this. Line it up with the clip already kind of on there,
and push until it seats down in there. And it's a tight fit. There we go. And now that is on there
good and tight. So the shape of the coupler and the fact that it's going through this pin
keeps the coupler from pulling out. It won't go up because of this clip. And you still do have
some self-centering action of a sort thanks to the clip. My original design for the coupler
included, you know, this self-centering mechanism, but I found it one only not necessary,
but also it got in the way. So when I print these now, I just cut that part off so that I have a
So for this particular project, having access to a 3D printer and a little bit of knowledge of how
to use it makes the project much cheaper, faster, and easier. For my purposes, I just use my Creality
Ender 3. This is a two-year-old machine. This is a pretty basic machine and a rather inexpensive
machine coming in at under $200. I had no prior experience with either CAD design or with 3D
printing. So when I made the purchase, I wanted something that one, wasn't super expensive and
two, was open source so that if I needed to upgrade or change out some of the components,
it was easy to do that because the parts are not proprietary to any particular brand.
So anyway, there are plenty of other machines out there, more complicated, more expensive,
and even the Ender 3 has been upgraded several times since I made my purchase two years ago.
So I use this all the time, much more than I thought I would. If you're interested, there is a
link in the description to the Ender 3 on Amazon. In full disclosure, I am an Amazon affiliate,
so if you follow the link, I could earn a small commission off of that. But feel free to investigate
and choose your own brand, what fits you. And so there's my finished product, and now it's just a
matter of putting the wheels and the contacts back together the way they belong. So I'm going to
reassemble this. I'm doing the contacts first. I needed to re-solder the wire here, which I had
already done, re-soldered that connection on here. That's why these lights weren't working.
And you see these little tabs go in the holes on the side of the truck
there, and then I'll use a screwdriver to pull the truck side out enough that the tabs will
fit down in their slot. That's in position, and now I will reinsert the wheels. Line them up,
give it a little bit of assistance with a small screwdriver. Always messes up when the camera's
on. There we go. All right, so one wheel is back in place. Do the same thing for the other side,
making sure that my axle makes contact with my grounding strip.
Okay, and now my truck is reassembled. My lights are rewired. Now my next step is to,
just like Lionel did 40 years ago, I'm going to take some clear tape, tape these wires to the
floor so that they're not visible through the windows, then replace my window strips. Again,
I'm just going to use some clear tape to hold them in place, and then screw my roof back on.
Okay, so first I'm just taping down these wires to keep them out of the windows.
Then next, make sure that with your window strips there are holes here where they were initially
attached inside the plastic. Make sure you orient the window strips so that those holes are not
visible in the windows. Make sure you've got the right strip on the right side. Okay, so this one
goes here and right side up. Cut off the excess. If there's any left over sticking up, it'll be
hidden by the roof. Let's put the roof back on. There we go. Okay, and there we have it,
a nice clean car with new color. Repeat the process for the other cars, and there we go.
Let's check it out on the layout. Okay, so with two brand new couplers, replacing,
pairing light bulbs and some wires, and my three-piece passenger set is ready to go.
Add in my locomotive on a brand new powered chassis, and here we have a complete passenger
set for under $50. So again, here it is. I spent $5 on each of the cars, $10 on the dummy,
$19 on the powered unit, a couple of dollars for a new headlight, a few pennies for the new couplers,
a pittance for masking tape and solder. So here it is, the Quicksilver Express. It's a nice little
set for my layout. I needed some passenger power. See what you can do. Think outside the box,
and bargains can be found. So I hope you like the video. Again, like it, share it, subscribe,
tell your friends, tell your neighbors. Give some comments. If you see something that you
think I did in a really weird way or you would have done differently, certainly put it in the
comments. Or if you found similar bargains out there, certainly let's celebrate those.
So until then, let's keep the trains running, and I'll see you next time on Toy Train Tips and Tricks.