I Bought the Ugliest Thrift Store Art: 15 DIY Transformations!

Thrifty Thinkers
9 followers
I bought the thrift store art that no one wanted. The outdated, faded, and ugly pieces.
And I'm not just repurposing the frames. I'm completely reworking the art itself. So today,
I'm taking 15 of the worst pieces I could find and giving them a second chance. I'm starting with
quick and easy fixes and working up to more creative and unexpected transformations. So
make sure you stick around for number 15 because that one is totally outside the box.
The first project started with this sweet little chipmunk print I found for $3.99.
I loved the vintage look of it, but that frame wasn't doing it any favors. It was one of those
plain modern black frames, you know, the kind you see everywhere. I was surprised to see that the
art was actually an educational poster dated 1971. I had thrifted this vintage frame with bubble
glass a while back and had been saving it for just the right project. And I thought the chipmunk
would be perfect. So I trimmed the print down to fit the frame's unusual shape. And since there
weren't any nails or staples to hold it in place, I just used some paper packing tape on the back
to secure it. I was attracted to this pretty colorful floral print, but I thought $5.99
was overpriced because if you look closely, you can see that the paper is wrinkled.
But I had an idea for smoothing those wrinkles out and giving this print a much more elevated
look. This modern wood frame seemed completely wrong for a floral print based on an 18th century
painting. So once again, I went to my stash and pulled out a vintage frame that I had previously
thrifted. It didn't have a backing, so I just reused the cardboard from the modern frame
and trimmed it down to fit inside the vintage one. Then I trimmed the print to the same size.
Since I wasn't using glass in this frame, I brushed a coat of Mod Podge right over the print
to protect it. And those visible brush strokes actually help it look more like a real painting
instead of just a paper print. Once the Mod Podge was completely dry, I flipped the print over and
lightly sprayed the back with adhesive. Then I attached it to the cardboard backing and
rolled over it with a brayer to smooth everything out. That took care of the wrinkles and gave it a
nice flat finish. Once again, there were no staples or nails to hold the backing in place,
so I just ran paper packing tape along all four sides of the cardboard to secure it.
This next piece honestly wasn't that bad. It just screamed generic, mass-produced artwork,
and I thought we could do better. When I take a frame apart, I try to remove the craft paper
from the back in one big piece so that I can reuse it later. When I saw the foam board inside,
I automatically assumed that both the print and the mat had been glued to it, which is common
with mass-produced art. But thankfully on this one, only the mat was attached, which left me
with a nice paper print to work with. I had also thrifted this $2 metal frame and thought it
coordinated nicely with the rose print. I decided to use the lower half of the print, and I trimmed
it to fit the new frame. Then I adhered it right over the existing print using spray adhesive.
Then I brushed over parts of the frame with gold Rub & Buff to highlight the gold background of
the print. I still had the top half of the print left and decided to use it on a small
Dollar Tree wooden box. To adhere it, I used spray adhesive because glossy paper like this
tends to wrinkle if you use a water-based product like Mod Podge. To finish off the box, I painted
the sides and inside with chalk paint. Then I lightly distressed the box and the print and
applied a light coat of antiquing wax, wiping most of it back. This print of a Renoir painting looks
so sad and cheap and was priced at only $1.44. Lucky for us, I had a nice mat and frame left over
from the previous project. I could have just reframed it and called it good, but Renoir deserves
more than that. So let's color drench the mat and the frame using a color from the print. I chose a
To avoid brush strokes, I used a foam roller to paint the mat.
Once the paint was dry, I taped the print to the back of the mat and put everything back together.
Before we jump into the next project, I want to thank Homoglow for sponsoring today's video.
As you guys know, my house was recently filmed to be featured on the Homeworthy YouTube channel
and website. And as you also know, I was really stressing about it because I wanted my house to
look perfect. I wanted to focus on finishing up some DIY projects, styling, and all those last
minute details, not scrubbing floors and baseboards. So I booked a cleaning with Homoglow
and having someone else clean my house really did reduce my stress level. If you're not familiar
with them, Homoglow is a top rated home service platform that makes it super easy for you to book
a trusted cleaner in your area. Everything is done online. You choose your date,
how many hours you need, and you can browse reviews, photos, and ratings from background
checked cleaners before booking. I'm very budget conscious, so I recommend checking out the Forever
Clean membership. It saves you $30 an hour on all future cleanings and you can book unlimited
cleanings starting as low as $19 an hour. Even after that first cleaning, the membership
practically pays for itself and you can log on any time and adjust your schedule or cancel.
So if you want to take home cleaning off your plate this year or just prepare for a special
event, head to homoglow.com slash Canterbury or scan the QR code on the screen and you'll get
your first three hours of cleaning for just $19. I love a round or oval frame even if it's an old
word sign. I think this one was someone's DIY project because the vinyl lettering was very
easy to pull off. The white background paired with the rustic wood was giving off farmhouse vibes,
so I painted over the white with black chalk paint to give it a more elegant updated look.
And since botanicals are so popular right now, I grabbed a hydrangea that I had recently pressed
from a bouquet my husband sent me and I hot glued it in the center of the wood round.
Then I added a bow made from a strip of thrifted vintage lace. I hadn't yet sealed the chalk paint
because I wanted to attach the flowers before applying any wax, so I just brushed around the
perimeter of the wood round. This next piece was definitely one of the ugliest prints at the
thrift store. I was even a little embarrassed to be seen buying it. And this was one of those
mass-produced pictures where everything is glued together. I had hoped to save the mat,
but there was just no way to remove it in one piece. So I pulled out a small solid wood frame
that I had thrifted for $1.99. Using the glass from that frame as a guide, I cut out a section
of the print with a utility knife. I don't think it really comes across on camera just how garish
these colors are. So to tone them down and give them an aged appearance, I brushed on a coat of
water-based antiquing wax. Then I came back with a paper towel and began dabbing it off until I
achieved a look I liked. I let the wax dry for a few hours, then I reassembled the frame, but I did
not replace the glass. The wax not only subdues the colors, but it protects the paper and creates
the look of an original painting. I also brushed some dark wax on the wood frame to freshen it up
and conceal any small scratches. I absolutely love how vintage this looks.
I still had plenty of that ugly picture left, so I decided to crop out my favorite part,
the little swan figurine. I wanted to use an old round frame that I had, and so I found a lid that
matched the size of the frame and traced around it so that I could cut it out with a pair of
heavy-duty scissors. Next I aged it with a little antiquing wax, just like I did with the rose print.
I brushed it on, dabbed most of it back off, and once it was dry, I placed it in the old frame.
Since the frame didn't have a backing, I cut another piece of cardboard to slip in behind
the print to help hold everything in place. If you like the size and shape of ceramic plaques
like this one, don't pass them by. They're actually so easy to repurpose. Just remove the hanging
hardware and flip it over. Most of the time the back is a clean slate just waiting to be embellished.
Once the back is cleaned up, you can add whatever you like, and since I like birds, I'm going to
apply an IOD rub-on transfer from the Katarina package, and it adhered so easily and perfectly.
Because I like the back to look finished too, I painted over the original design with a couple
coats of ivory chalk paint. Then instead of reattaching the leather tie, I added a coordinating
ribbon for hanging. Since painted ceramic scratches fairly easily, I decided I better protect it with
a coat of Mod Podge on the back. This next piece of wall art might actually be even uglier than that
garish rose print. In the center was a printed piece of plexiglass that said
relax, but I couldn't relax until that entire design was gone, so I used a little goof-off to
soften it up, then carefully scraped it off with a razor blade. I could have replaced the insert
altogether, but I really wanted to challenge myself and see if I could make that plexiglass
work, so I chose a floral rub-on transfer from IOD's Clementine set and applied it to the front.
The frame was covered in paper that looked like rustic wood planks, so I lightly sanded it with
my orbital sander to rough up the surface before adding something new. Then I sprayed adhesive on
both the paper and on the back of a piece of scrapbook paper. I pressed the paper onto the
front and rolled over it with a brayer to make sure it adhered really well. Then I used a utility
knife to carefully trim away the excess paper from the center opening and around the outer edges.
Once most of it was removed, I went back over all the edges with a sanding block to clean up
any little bits and give it a more natural finished look. I decided to use a coordinating
piece of scrapbook paper to cover the center square, since you could still see it even with
the plexiglass in place. So I cut it to size and adhered it with spray adhesive. Then I just popped
the plexiglass back in the frame. I thrifted this old home interiors print in a burgundy frame,
and it just screams 1990s. As I began taking it apart, I was hoping the print and mat were not
glued to the cardboard backing, but no such luck. Before tearing off the mat, I scored the print
along the edge of the mat so that the print wouldn't rip when I pulled it off. I had thrifted
a moss-covered styrofoam wreath form for just $0.99, and I hoped to use it as an unusual picture
frame. I placed it on the print in a way that would feature the landscape rather than the woman.
Then I traced around it and cut out the circle with heavy-duty scissors. After removing the
wreath's paper backing, I used hot glue to attach it to the cardboard print. I also added some
staples just to make sure it stayed put. I think the plain wreath looks nice, but you know I can't
leave it plain, especially since I have a large stash of faux flowers. I chose some lavender, pink,
and blue flowers to reflect the colors of the print, just cutting down the stems and pushing
them into the styrofoam. I also hot glued some moss clumps over and in between the stems to further
secure them in place. When arranging flowers, I like to have something tall in back and something
droopy along the front bottom. Other than that, I just play around with the arrangement until I
like it. Once I was happy with this arrangement, I created a hanger at the top by hot gluing a
loop of ribbon to the back of the cardboard.
Although these cast iron trivets can be used as hot pads, many people, like me, use them as kitchen
decor. You can easily update the design on the ceramic tile if you don't like it, and in a way
that won't damage the tile itself. Cut a little batting to fit over the tile, then cut a small
piece of scrap fabric. I'm using a piece cut from a thrift store curtain. Trim the fabric to slightly
larger than the tile and place the tile face down on the fabric with the batting sandwiched in
between. Cut slits around the edges of the fabric and then fold the flaps over to the back of the
tile and hot glue them in place. To clean up the bottom, I cut a circle from a piece of cardstock
and hot glued it over the fabric edges on the back of the tile. For an extra embellishment, I glued
some braided ribbon around the sides of the tile. Then I just hot glued the tile back into the cast
iron trivet. And for a final touch, I added a bow to the handle. Like the home interior's picture,
these floral prints weren't terrible. They were just really generic. So let's take them apart
and give them some personality. Patterned mats are really popular right now, so I found a piece
of scrapbook paper with a floral pattern that I thought looked nice with the prints. Unfortunately,
the prints were adhered to foam board and there was no additional cardboard backing, so I decided
to use the glass for the back. I cut my scrapbook paper to fit and adhered it directly to the glass
with spray adhesive. Even though it looks like the prints have a mat, they don't. It's just the way
the image was printed on the paper. So I used a metal ruler and a utility knife to cut off that
fake mat border. Then I used a sanding block to smooth the foam board edges. I used clear glue
to attach the foam board to the paper covered glass. I used regular glue rather than hot glue
because I wanted to have time to adjust the foam board and make sure it was centered on the glass.
I let the glue dry overnight and the next day I reassembled the frames. I needed to cut out a
piece of cardboard to place behind the glass so everything would fit in the frame properly.
Then I just used some paper packing tape along the edges to clean up the back. I wanted to add
another dimensional item, so I pulled out my Dollar Tree butterfly stickers. I like to trim
off the excess transparency around the edges so they look a little less like stickers. Then I just
use a drop of hot glue on the body to attach them. I'm sure these four blocks that spell out fall
were once considered cute, but since I thrifted the set for just $2.99, even the Goodwill employees
thought they looked dated. So let's give them a quick fix by covering them with leftover wallpaper
scraps. I wanted to use this William Morris wallpaper, but I only had enough to cover three
of the blocks, so we'll do something different with the fourth one. I tried to arrange the wallpaper
to feature a prominent design on each block, but since I was using scraps, I didn't have a lot of
options, so I cut out a few extra images to add in selected spots. Since this is peel and stick
wallpaper, it was super easy to apply. After trimming off the excess, I ran a sanding block
along the sides to create a more natural looking edge. Although I was happy with how they looked,
I thought a little antiquing wax would make them look a little more like vintage art and less like
wallpaper. But if you prefer the brighter colors, just skip this step. Now what to do with that
fourth block? Although it may look like a solid piece of wood, it's actually a hollow box, and I
thought it would be fun to create a hole in the center. So I marked the center and drilled a hole
in that spot, and then I drew a larger circle around that. I was going to use the hole as a
starting spot for my jigsaw, but it's really cold in my garage right now, so I grabbed my
dremel instead and used that to cut out along my pencil line. My jigsaw would definitely have cut
out a cleaner circle, but it didn't look too bad after I sanded the edges. I wanted to place moss
inside the box to create a tiny hidden garden, so I hot glued individual clumps to the back wall.
I also hot glued a piece of styrofoam along the bottom edge of the circle as support for other
things I might want to add, but first I wanted to decoupage a napkin to the front to add a pattern
to that plain brown box. I brushed on an even coat of Mod Podge over the box and then pressed just
the top patterned ply of the napkin into the Mod Podge, smoothing out any wrinkles with my fingers.
Then I applied a top coat of Mod Podge to seal the napkin. Once the Mod Podge was dry, I used
a sanding block to remove the excess napkin along the sides and inside the circle. Then I hot glued
a moss covered wire around the circle, which not only cleans up the cut wood edges, but also
contributes to that garden theme. I found a green piece of bark-like material in the bag of moss
and hot glued that to the styrofoam to create a little shelf. I also glued some dried mushrooms
to the box. I found these in my yard last fall. Then I filled in with some faux greenery and dried
flowers. I just wasn't loving the look of the decoupage napkin and I thought that I might have
a leftover piece of scrapbook paper that looked like birch bark. I found two small pieces and
I thought if I tore them into a few smaller sections, I should have enough to cover the
front of the box. I removed the mushrooms and protected the moss with a paper towel.
Then I used spray adhesive and applied the paper directly over the sealed napkin. I immediately
liked this so much better. Unfortunately, I didn't do a great job of cutting around the moss covered
wire, so I cut up a few clumps of moss into thin strips and hot glued those around the circle
opening. This worked so well. You really don't need to use that wire for this project. My miniature
garden needed something else and you know I wanted to add a bird, but I challenged myself to use
something different. I found a mushroom Christmas ornament in my stash that I thought would look
cute, so I just used some wire snips to cut off the metal ring at the top. Then I pulled out the
straw flowers and added the mushroom inside instead. I hunted through my miniatures and found
a small squirrel and he fit perfectly under the mushroom. Then I just added some tiny faux flowers
on the opposite side of the mushroom to balance out the arrangement. Which of today's ideas was
your favorite? I hope you'll let me know. And if you want some unique ideas for repurposing those
picture frames, here's another video I think you'll like. Thanks so much for watching today.
Hope to see you next week!
