Motorcycle Brake Fluid Change Motorcycle Ways

Two-Wheeler Technology
5 followers
5 Video Views·Feb 24, 2026
A Step by Step guide on how to do a Motorcycle Brake Fluid Change.. by motorcycle ways | Is your motorcycle due a brake fluid change?
Welcome to Motorcycle Aways. Did you know it's recommended to flush the brake fluid on your
motorcycle every two years regardless of mileage? So today I'm going to flush the front brakes of
my Honda CB500X and this is the same procedure you'd follow if you were to flush the brakes on
your bike. So let's get started. Now we're going to start here by removing the cover of our front
brake fluid reservoir. So I'm just going to give it a quick wipe with a damp cloth first,
take any dust and dirt from around it, stop it going into your fluid. It's important that you
don't get dirt and dust into your brake fluid. And if you're wondering what type of brake fluid
you use for this, it'll be written on the top of your cover here. You can see this is DOT4.
So just check the top of the cover on the reservoir and it will surely tell you what
fluid you should be using. Now I'm just going to cover up the paintwork with some
old rags here and that because brake fluid is not nice stuff to be working with and if it gets on
the paint it can destroy the paint and remove some of it or certainly mark it anyway. So try and
cover up your paintwork as best you can and keep your brake fluid from getting on the different
components. Now to remove these is two Phillips screws here. A lot of people do have difficulty
with these if you haven't got the right screwdriver to fit correctly and the reason for that is you
might not have the right screwdriver. A lot of the Japanese bikes use JIS screws,
Japanese Industrial Standard I believe it stands for, and you know if they're JIS screws but you
will see a dot on the top of the screw, it's like a punch hole on the top of the screw. These don't
have them actually so they're not JIS but a lot of Japanese bikes will have them and there's a
special Starhead screwdriver, JIS screwdriver that fits snugly into the screw so when you
fit your screw onto your screwdriver you shouldn't have any play in it, it should be a tight fit.
If you have a bit of play then if these screws are anyway corroded then it can be hard to remove
them and people have difficulty removing them so just be careful and watch out for that,
that you have your right screwdriver that fits correctly. So now I'll just remove the cap
and inside there's another cover, white cover and under that there should be a black diaphragm.
So gently prise it up if you have to and there is your black diaphragm. So I'll just give you a
closer look at the fluid, you can see there it is brown in colour so the darker your fluid gets
the more it is in need of changing. When it gets dark and cloudy, sort of a browny colour then
it definitely needs changing because it gets contaminated with moisture over time and that's
the reason the moisture actually believe it or not can be drawn in through the brake pipes,
the pores in the brake pipes and it can be even drawn in here through the cap over time and the
moisture gets into the fluid then when your brakes heat up the fluid heats up and the water and
boils and gets to boiling point and then you get a soft spongy brake lever and brake pedal and that
so that's why they recommend every two years to change them for safety. So what I'm going to do
is siphon out this fluid that's in here first instead of flushing it down through the system
and out through the bleed nipple I'm going to siphon out what's in the reservoir because you
don't want to be putting on that dirty fluid down through the system there's no need. So in order
to siphon it out I've got a syringe here it should hopefully remove it for me. So now we can see
that that has taken the majority of the fluid out of the reservoir there. So now I've got some brand
new MANO DOT 4 brake fluid here freshly bought so that's what you want to be using you don't
want to be using old fluids you have in the shed which is left there lying for a while especially
if it's open because the moisture will get into the container the same as it will into your brake
system so then it's no good. So this one is unopened and it's just bought today so next step
is to fill up the reservoir with new fluid and then we'll bleed it out to the bleed nipple below
so you can see how clear that fluid is compared to the old fluid that came out of it
it's clear in color so that's the difference so now our next step is to bleed the calipers
and I'm going to keep the reservoir topped up fully as I go along and keep bleeding them until
I flush out the old fluid and the new fluid comes through and we get all the air out of the system
so this bike has got twin discs on the front twin brakes so two calipers so we're going to start
with one on the left hand side you should start with the one furthest away from your master
cylinder so we're going to start over here with this caliper on the left hand side now so another
tool that I have here is an eight mil spanner that's to fit the bleed nipple to open and close
the bleed nipple and a bottle with a 3 16th hose on it it's a clear hose 3 16th in size so that
fits over your bleed nipple nice and tight and I put a hole in the top of the bottle so the hose
fed down through it to stay in place and some clean fluid in the bottle some clean brake fluid
and a couple of rags to clean up any spillage so what we're going to do is flush down the new fluid
and keep bleeding it until the old fluid is flushed out and the new fluid comes through
and we get the air out of it so I'll start by removing the dust cap off the bleed nipple
and then we'll place the eight mil spanner on it use the the ring side of the spanner rather than
the open side and place it on in a position where you have room to swing it around there to open
and close it without having to take off the spanner because the hose will be going on here
next on it fits tightly into the bleed nipple there so now what I'll be doing is pumping the
brake lever and when I have it held pressed I'll open this and let the fluid out and close this
and then release the brake lever again to get the new fluid through and push out the old fluid
so let's see how that goes so squeeze the brake lever open the bleed nipple close it
and release the brake lever another idea here if your tube is not staying straight and
needs to be tightened up and put a little cable tie on the end of it
to tighten it up stop air being sucked in at the end of the pipe there just a small cable tie like
that to hold it in place and stop air going into it so that might might be a help and just keep
in mind keep your level of the reservoir topped up you don't want it going down low because it'll
it'll be sucking in air then and you could be there all day bleeding so just keep that in mind
keep your keep an eye on your reservoir that doesn't go down too low while you're bleeding
so now that's the left side done we'll do the same procedure over on the other caliper
put our spanner in position again in the hose pipe and again we'll put on a cable tie on the
stop any air seeping through and if you're not confident working with brakes or brakes are
as you know vitally important so anything goes wrong can be fatal so if you're not confident
doing a job with brakes then you know get a mechanic or go to the dealer and have the job
done because it is something you need to have right on the bike so now we'll pump the lever again
holding the lever we'll open the lead nipple and close and release the lever
so now that's the system bled we carefully take off our hose again just remove it nice and gently
and hold it up the way so let the fluid down into the bottle and we'll be disposing of that
fluid carefully and just one check to see that the nipple is tightened up again and give it a
clean roundabout take any fluid that's spilt away from it and put on the dust cap again
and check our brake lever so we'll just top up our fluid there a small bit
and you don't want to overfill it but it's um once it's up there to the top of the window
that's high enough just put back on um the cover again black diaphragm and all three covers are
there together make sure that sits on the right way two screws snip them up firmly just be careful
not to over tighten them because you don't want to crack the cover and give it a wipe clean around
take any break through that might have fallen down there spilt so i debated for a while whether
i was going to change the fluid or not flush it out and because they do recommend every two years
you should do it and my bike is three years old now so it's time to do it but um if you're thinking
about doing it and i'm wondering whether you should or not uh let me show you something here
first there we have two samples on the bench the one on the right is the fluid that i drained out
with the syringe that came out of the reservoir and the one on the left is clean brake fluid
so you can clearly see the difference there and the color between the two
the one on the right is much browner much darker in color so that's a sign that it
is contaminated with moisture so you don't want that in your brakes on the motorcycle
because when they heat up that fluid heats up and then the water then in the fluid
starts to boil and that's what gives you a spongy spongy brake and in very bad cases
brake failure so it's definitely worth doing so that's that's out of my bike there now that's
three years old my bike so i know some people do let them go longer four or five six years and
they don't change the fluid so you can imagine how it'll be like then so it's nothing to do with
mileage really it's to do with time moisture seeps into the fluid over time and that's what
causes the problem so that's a front brake flush done on the honda cb500x i will be doing the rear
brakes soon on another video so watch out for that one and i hope you found it useful
thank you very much for watching and i'll see you on the next one
