Man Says He Can't Find Wall Stud Then Does It Anyway/DIY for Beginners

VideoJoeKnows
63 followers
3 Video Views·Feb 21, 2026
@VideoJoeKnows
Man says he can't find wall stud then does it anyway/DIY for beginners is what this DIY howto video is about. VideoJoe is getting ready to install a wall mount TV & one of the important things he needs to do is to find a wall stud, or wall studs, in order to mount the TV wall bracket to so the wall mounted TV doesn't fall off the wall! Should be easy enough to find a wall stud...shouldn't it? Watch & learn as VideoJoeShows you what VideoJoeKnows...man says he can't find wall stud then does it anyway/DIY for beginners. Nice!
https://www.youtube.com/user/VideoJoeShows
AI Generated·May contain errors
So ideally what we got was three and three quarters over from there. Remember?
Okay, so I'm just going to hold my pin up here. This is not exact. It's going to be close enough
right now. Ideally that's where I'd like to put my bracket up on the wall. But now
there might not be a stud exactly there. Okay, so now I've got to figure out where the studs are.
And here's the other thing. You see where that is going to go? And here's a plug here.
And here's the cable for the TV. Now I know that there's probably a stud either right there
beside this box or right there beside the box. The same thing over here is probably going to be
right there or right there because the studs are probably 16 inches on center.
The box is usually nailed to the edge of a stud either here or over there. So if I just hold my
tape there to about there, I can see that that's going to be about where a stud could be or it's
going to be there and there. That's not always gospel. Okay, because they might have laid out
the wall differently. It might be two foot on center. They might have had to add another stud
in the wall for something. This could be a cut-in box for all you know. And it might not even be
next to a stud. So those are the types of things we need to look at. And you know, if I have to go
over to the edge of that plug, that's okay. That's still pretty close to center of the wall.
You know what I mean? So what's our next step? We need to find out where the stud is, don't we?
You want to do that a couple times on the wall. So I'm over on the right hand side of that plug
and this looks like 16 inch center like I was saying before. There's probably a stud right
there. Sometimes when you put this on the wall, if it starts, you may have to clear it,
push the button a couple times and then start sliding it. Now see, I know I'm starting to hit
something because it's red and then it comes up. You know, that time it's just flashing.
Usually the red light, boom, boom, boom, boom, green, red, red, red, green. And this one's not
doing that this time. But I know there's a stud probably right there. You can knock on the wall
too. You hear that? Higher pitch, lower hollow pitch means there's nothing there. So see this
wall is hollow in here. No stud at all. When I get close to a stud, listen, it's a definite
different noise. Hollow, solid, high pitch. It's kind of a feel. So there's another way to check.
I'm going to show you one other way you can do it as well. I went ahead and marked this
and all that, but I'm just going to kind of go through the motions with you. I went up,
I went to 69 and three eighths and I put myself a mark there. Then I had to figure out about where
the center of that stud was. And I came over and put a mark there. Then I had to start probing
with some nails. And that's what these two little nail marks are, were, you know, and I, and I didn't
want to make that too close to where the hole was. So I just started tapping in here to make sure I
could hit the stud. I wanted to make sure once I hit the stud, I went over at a little bit of an
angle this way. And then I started over here and went that way. So I could know about where the
outside edge of the stud is here and over there. Because the last thing I want is if I put the
nail straight in, if I hit the stud, okay, there's a stud, no problem. Well, you've got to get,
you've got to make sure you drill your holes in the center of that stud. You don't want to be on
the edge of a stud and then put a mark up there and say, oh, that's fine. The stud's an inch and
a half wide. What's the problem? You got to find the middle. You need to find the middle of the
stud. That's what I did. I put a mark down there and, um, I came up from the bottom and, uh, well,
first I put the mark and then I got my level up here and ran that. I wanted to make sure I was
going up nice and plumb and I put a pencil mark on there and all that. And, uh, I put a pencil
line there and I also had to measure the bracket because I didn't want the pencil line to go up
above the bracket because that's not, that wouldn't show, you know, that would show on the wall when I
got all done. Then I transferred my, my whole pattern up there and, uh, did all that. I got
a scratch all like this. I put it right in the middle there, tapped on there to get my little
marks and I drilled holes there. You have to, before you drill those holes, see those holes are
for these lag bolts. A lag bolt that goes in there and, uh, you've got to do a pilot hole in there
first. So I just looked at the directions and got the corresponding drill bit size, uh, that I needed
and then I drilled that because the last thing you want is to get a drill bit, um, just, you know,
you think you know which one it is, you put one too big in there, you draw all three of your holes
and now these, once you put these in, they spin or something. Or, I mean, I'd rather have a smaller
hole first and try one. If it's too hard, take it out, do another pilot hole. But, you know, with, uh,
the same pilot hole but a bigger drill bit. But I didn't do that this time because I read the
directions, looked at there and it told me which drill bit size to use. So that's what I did.
And now we're ready for the next step. Before I take my bracket up there, I got that drilled.
I just wanted to put this in here. I wanted to make sure it was right. So I got my ratchet set
and, um, I got to go through the sheetrock and, and it almost seems like they put two layers of
sheetrock here or something because it, it was thicker than half-inch. Usually your sheetrock
is either half-inch or five-eighths on the wall and this might have been two layers for some
reason. But anyways, the bolts are very long and so I'm just going to get a hole. Get this down in
there all the way. Just want to get ready to hold the bracket up there. These bolts are going to go
in nice and easy. Okay, got to have a ratchet set for this. You don't need a real expensive ratchet
set, just a cheapo one. You do that on all your holes. That way it's going to go in nice and easy.
Make sure you, you know, you don't want to hit a knot or something and mess with it as you're
trying to hold the bracket up there and the bracket slides and scratches your wall and all that.
You know what I mean? Okay, have I showed you something so far that you don't think you can do?
You can do this, come on. I know you can do this. You just follow these steps. I don't want you
being afraid of your project. You've never done this before, that's okay. I think you still can
do it. If you don't think you can do it, you know, you can get a friend over to look at the video
and show it to him and he can help you. All kinds of things you can do to do your project. I don't
want you spending an arm and a leg to pay somebody to come over here and put this TV up for you
because you know what? Once you put up one TV, you're going to say, oh, I want to do that down
in the den. I want to do that in the spare bedroom, in the family room, whatever. Most
people have more than one TV and nowadays people are putting them up on the walls. If you can do
one, you can do all of them. All right, here's the bracket. Make sure you put it
about the right way and gotta be careful with this because I don't want to scratch up the wall.
I can put this in and kind of get it started because I've already kind of pre-set those.
Okay, so hold that up there. I'm doing this project by myself.
If you have somebody to help you, that'll be good too.
They can watch you, you can watch them. Between the two of you, hopefully you don't screw up.
I'm not going to tighten those yet. Let's get them started. I'm going to get all these three
up here.
I have all these holes lined up pretty straight
and I'm going to take my level and kind of look at it a little bit.
But if it's, if you get it and if it's not a hundred percent perfect on being level,
plumb is, plumb means level but straight up and down. So if I say plumb,
you'll know what that means from now on. This should be pretty close to level but before I
tighten it down, I'm just going to kind of hold my level up here and take a look at it.
And it looks like the top, this top edge needs to go over or the bottom needs to go that way
a little bit. So let's see if I got a little bit of a slop here. I got a little bit. Okay,
so I'm just going to kind of push that over as much as I can. I want to try to
not get my grubbies all over the wall but if I do, I can wipe that off. Okay, now,
now I can tighten this up.
Now I can do the middle. You want these snug. You don't want to go so far and say the tighter the
better because trust me, you go too tight on these, you could actually snap and twist the
head right off of a lag bolt. I didn't know it was possible until I did it one day. You do that
and there's not much you can do about putting another bolt in. You know what I mean?
You just want it snug. Okay, now I check that with the level and see what's up with that.
That's right on. Beautiful. Now if yours is not perfectly level, let's say it's off a little bit,
don't fret. You don't have to have that bracket 100% plumb because once we install the TV on here
and it hangs, this bracket assembly, we can adjust it. There's adjustments. There'll be
adjustments. I got to look at that. There's an adjustment that you can swivel it and you can line
the TV up exactly level. Did you know that? So that's how it's going to work. You see that the
actual center of the TV is right here. Okay, but you can pull it, you know, this swivels out like
this. You can pull it out like that. You can have the center of the TV over here if you want,
way over here. You can tilt that at an angle and have your TV kind of coming out this way. So
there's lots of things you can do with this bracket assembly. You can slide it over there
like that, whatever. Lots of different options.
