How To Build The Perfect Raised Garden Bed

Garden Bliss
2 followers
4 Video Views·Feb 8, 2026
Comments are disabled for this video.
What's growing on gardeners? Today I'm going to show you how to build the perfect raised bed.
This bed is affordable, strong, will last a decade or longer, can be built using basic tools without
much skill, and can be tailored to any dimensions that you need. This proven design is what I am
using for all of the new beds I'm putting in my garden, and I can't wait to share it with you all.
If you're new to the channel, please subscribe, hit the bell for notifications,
and check out my Amazon store and Spreadshop links in the video description for everything
I use in my garden and awesome custom apparel and gear. The example raised garden bed that I
will be building in this video will be 7 feet long, 4 feet wide, and 16 inches deep,
but you can tailor your design to make your bed as long or as deep as you want. Want it longer?
Just use longer boards. Want it deeper? Just use wider boards or stack another row of boards to
increase the depth. The only caution that I will give you is to never make your raised
garden beds wider than 4 feet because the typical human can only reach about 2 feet.
If you exceed 4 feet of width, you will struggle to reach the center of your bed.
You can make your bed narrower than 4 feet if you want, but don't exceed 4 feet in width unless
you're like an NBA point guard or something. Throughout this video, I will be using a
number of different materials and tools to make building this raised garden bed simple.
I will place links to everything I possibly can down in the video description. Obviously,
the wood is something that you will need to pick up locally. All of the wood that I'm using in
this video to build the raised bed is number 2 prime pressure treated lumber rated for ground
contact that I got from my local Lowe's store. Which brings me to my next point. Do not use
untreated lumber or lumber not rated for ground contact to build your raised beds or they will
only last a few years. I use pressure treated lumber because it is affordable and readily
available at any big box store. All of my original raised garden beds use it and they are 7 years old
and show no signs of rot despite my incredibly wet, humid climate. 10 years of life is easily
achievable using proper pressure treated lumber. No pressure treated lumber is not toxic for
gardening and hasn't been so for nearly 3 decades in the United States. Modern residential pressure
treated lumber is treated with copper which is, by the way, often directly sprayed on all the
fruits and vegetables that you are buying at the store, even the organic food because you can buy
organic certified liquid copper concentrate. Copper solution has been used in gardening since
the 1800s. I'll link to a detailed video both above and down in the video description as to
why I believe it is okay to use pressure treated lumber treated with copper solution in your garden
but at the end of the day it is your decision. Woods like redwood, cedar, and cypress are somewhat
naturally rot resistant alternatives to pressure treated lumber but they still likely will not last
as long as pressure treated lumber that is rated for ground contact and that wood will cost you
several times more. It's up to you. Each raised bed requires the following materials. 4 2x8 boards cut
to 7 feet, 4 2x8 boards cut to 4 feet, 2 2x4 boards cut to 4 feet, 2 2x4 boards cut to 80 inches,
8 2x4 boards cut to 14 inches, and a box of number 10 3-inch wood screws. The tools I will
be using are a drill, impact driver, speed square, measuring tape, drill bit, gloves, eye protection,
and a pencil. A circular saw and Japanese pull saw were initially used to pre-cut all of the
lumber boards to length. I'm going to build this raised garden bed in two identical layers on my
concrete driveway apron because this is the best level surface that I have. Then I'm going
to move both sections into my garden for final assembly because the final raised bed is going
to be so heavy that I will never be able to move it. Do not build this raised bed in its entirety
outside of its final location or you are going to have a horrible time picking it up and relocating
it. Each individual section on its own is fairly heavy but it is manageable to move them with two
people so please keep that in mind. Another thing that you'll want to do is lay the best face of
each board top side up because this number two prime lumber, well they're all going to have knots
and little imperfections in them so we want to make sure that the nice side faces out so our
raised beds look as good as possible and we place the knotted sides facing inward where no one will
see them. We will also want to make sure that when it comes to the tops of the boards that we have
the nice side facing up and if there's any imperfections on the tops of the boards then we
face them downward where no one is going to see them. The first thing we will do is we will lay
out our width boards and then using a speed square we will draw a line three quarters of an inch in
from all of the ends because this is where our screws are going to be and the individual joists
are an inch and a half thick so that three quarter inch line is going to have our screws
pretty much centered when we mount this board. Then in an assembly-like fashion we will take
our drill and we will pre-drill three holes on each side of the width boards in line with the
pencil line that we just made. Pre-drilling the lumber is very important so we don't accidentally
split the wood when we are installing the screws. Now using the impact driver I'm going to partially
install screws in each of the holes and insert them about just a quarter of the way in. Now we
have our width board lined up against two of the length boards. Now we are going to start
installing our screws. Now we don't want to install the screws completely from the get-go
because the lumber is going to try to twist on you so I'm going to embed each screw about another
fifty percent of the way until it makes contact with the length board and then I'm going to finish
that process for all three screws and then if they try to twist on me I'll be able to twist
the lumber back in the direction I want it to go. Then once everything is lined up we will actually
fully embed the screws. So now I have the bottom half of my raised bed and I'm happy with the way
it came out. Now in order to build the second half of my raised bed I'm going to have to move this
into my garden to make room so I can build the other half here on my driveway apron. So I'm going
to take my garden cart and I'm going to use that to wheel my first half of the raised garden bed
over and into my garden as well as some of the other wood that I'm going to use for railings and
supports to lock the two halves together. Then once I move all that stuff into my garden I'm going to
build the second half of the raised bed on the driveway apron and bring that into my garden.
Remember don't try to move this yourself. It's pretty heavy. I don't have another person to help
me at the time so I'm going to use my garden cart to accomplish this. Now we have both halves of our
raised bed stacked on top of each other which basically fits perfectly because we built them
to the exact same specification. Now we are going to connect the two halves together and also install
a railing system all around the bed because I want to be able to sit on my raised bed as I work.
It is a lifesaver and in order to do that I'm going to use these 14 inch long piece of 2x4s
that I cut and that is going to both act as a bracing system that sucks in the sides of the
bed so everything is uniform because there's a little bit of bowing on each of these individual
pieces of wood and it's also going to add extra support for the railing to sit on because the
railings are made out of 2x4s which are three and a half inches wide and this joist is only
an inch and a half thick so you can't rest a 2x4 on that without additional bracing. Now if you
want a bigger seat you can make railings out of 2x6s and get yourself a 4x4 post and cut that
into 14 inch sections and use that. That's an option as well but this is the cheapest way to
do it. Now I cut two different sizes for the railings to sit on. I cut four foot pieces which
are going to go width wise and that is going to be the full width of the raised bed because I think
it's less wasteful this way. You basically get two perfect width railings out of an eight foot piece
of lumber with very little extra to spare so it's a really efficient use and I'm going to bring you
in closer and show you how I do this. Now when we install the wooden braces whether it is lengthwise
or widthwise we are going to install braces in all four corners and at the center both in the
width and the length. Now if I were using 10 foot long boards or 12 foot long boards I probably would
have to add two braces in the center equidistantly spaced so the way I'm going to do this is when I
place this brace in the corner it has to go this way. It has to be parallel to the length board not
the width board because if I made it parallel with the width board when I place my railing on top of
it it's only going to be able to support this railing. It won't be able to support the railing
that goes this way so when I spin it in this direction it is wide enough that I can both
support this railing and then it has a nice chunk left over right here that can support the the
length railing as well. So I'm going to take my speed square and on the length side of my raised
bed I'm going to choose a point about an inch and a half to two inches away from the edge of each of
the length board and I'm going to draw a pencil line down and then I'm going to pre-drill the
locations with two screw holes in each board. I'm going to choose the top and the bottom of the top
board and the top and the center of the bottom board because I purposefully cut these braces
an inch shorter than the depth of the bed so it would give me a little bit of wiggle room. Then
on the width side of the board I'm going to choose a location two and a quarter inches in because
that is going to give me an inch and a half for the joist width plus another three quarters of
an inch in so the screws go dead center into the two by four brace. And just like before we will
pre-drill our holes and pre-install our screws. Then we are going to place our brace and we want
this brace to be once again parallel to the length side because of the way I cut my railings. So we
want to make sure that the brace is roughly flush with the top of the raised garden bed because that
is going to support the corners of our railing. So once we have that in place we are then going
to finish installing our screws and then we will do the same thing to the other three corners of
the raised bed. Now we have all four of our corner braces on we have to add the four braces in the
center of each side of the raised bed. Now because this bed is only seven feet long I think one center
brace is going to be enough but if your raised bed was say 10 or 12 feet long well now you're
going to have to come in three or four feet on each side in order to completely suck in this
board because the boards will bow a little bit. This is all normal. So what I'm going to do is
I'm going to take my tape measure and I'm going to measure this board which is exactly seven feet
and I'm going to pick 42 inches which is three and a half feet and that is going to be dead center
in this board. So again I'm going to take my speed square and I'm going to run it down at that mark
and then I'm going to pre-drill some holes, pre-install some screws and then install our
two by four brace so the top is perfectly flush and centered with the raised bed.
Now all of the boards are nice and flush I'm going to go around to the other three sides
and do the same thing. Now we're going to install the railings and we're going to begin
on the width side not the length side. So this has been cut to be the exact length that I want
and then once we have the board where we want it I'm going to pre-drill one hole on each side to
hold it in place. Now that that one's in we'll make sure that this side is lined up and everything
is flush and it is. So now that this is secured and flushed we're going to install two more screws
one there and one here on each side and then here there is another brace so we're going to install
one through the center of the joist and then one through the center of the brace and now that the
width board has been attached we are going to install the two length boards next and we will
place the second width board last and the reason why is just in case we made a mistake cutting the
length boards and as you can see I wasn't perfect with this cut because I used a circular saw to do
it so it's literally the width of the saw blade that makes all the difference but you know what
it's close enough it's good enough I'm happy with the way this turned out so let's install the final
screws. Looking good and just like that my raised bed garden is done. I am so happy with the way
this turned out and I can't wait to take you in for a closer look but I can't right now because
it is pitch black outside it may not look that way but that's because I have the f-stop of my lens
cranked all the way down to 2.8 and my shutter speed is on 30 so if I took you in for a closer
look it would blur and pixelate. Tomorrow is supposed to be a beautiful day and I will take
you in for a closer look then when the sun comes up but for now I believe in squeezing every drop
of daylight out of these wonderful spring days. So now that it's daylight again this is the final
product I am so happy with the way this came out it is nice and straight nice and uniform and it
looks pretty professionally built. I am not a good woodworker I'm actually fairly lousy when it comes
to building things and I can do this in only about 90 minutes so I know that you can do it as well
so if you're worried about building something like this don't be you can do this as a novice
fairly quickly and you can see the raised beds that I'm putting together right now this is
shaping up to be a really nice new raised bed garden and here is an inside shot of the raised
garden bed you can see how those two by four supports that I built are holding the two halves
of the raised garden bed together while also giving the raised garden bed support for that
railing for you to sit on to make gardening more comfortable and then here is a shot of the width
portion of the bed that shows the same supports and once again one final shot of the railing
system so you can sit your butt down while you are gardening this makes things so much easier
on your back let me tell you. All my new raised garden beds are following this design this raised
garden bed was made out of the old six-year-old perimeter beds that I stripped down and I
repurposed and recycled that wood then my two new beds right here I built out of brand new lumber
and I'm going to build two more to go into that available space over there so now that I have
showed you all my favorite raised garden bed design some of you may be wondering why did I
decide to go with a wood bed design and not those modular metal raised garden beds I thought you
liked them well I do metal beds are great for a number of reasons and I recommend them to folks
all the time that are working with limited space maybe you don't have a means of sourcing or
picking up lumber maybe you don't have the tools or you physically can't build the wooden beds I
have metal raised garden beds all over my yard squeezed in tight places where wood beds wouldn't
work so well but for my core garden wood beds are superior they're sturdier you can attach PVC hoops
to them and outfit them with covers like frost cloth insect netting and shade cloth which is
critical where I live and you can sit on them like I'm doing right now which makes my life so much
easier and I think they look better nothing beats the beauty of uniform wood beds in my opinion and
if you use proper pressure treated lumber they should last just about as long as those metal
beds to me the ultimate gardening setup uses both where your big beds are wood beds and your
supplemental beds are metal where it makes sense to use them I'll place some links down in the
video description to the affordable raised garden beds made of metal that I use as well and that
right there is how to build what I think is the perfect raised garden bed and remember these
dimensions are completely malleable so make them bigger or smaller as you need for your unique
situation so everybody I sure hope you found this video helpful if you did please make sure to hit
that like button subscribe to the channel and please ring the notification bell so you're
notified when I release more videos like these remember I have a full list of tools and materials
down in the video description with links to everything that you can possibly source online
as well for your convenience for everything else I use in real life in my garden that stuff is all
linked down in the video description in my amazon storefront link so expand the video description
click on the amazon storefront link and you'll see everything I use in real life in my garden
and while you're down there please check out my spreadshop for custom merch if you want to
support my channel thank you all so much for watching and I hope to see all of you again on
the next video dale we have to start being very careful in our walks around the pond look there's
the first gator of the year the very first gator of the year they're back out alley gator is back
what do you think about that buddy you always have to be careful when you're walking around
ponds in southeastern north carolina because there might be a gator sunning oh he's gone he's
hiding oh there he is there he is there's a big guy right there look at him go isn't that cool
dale look you guys have the same snoot you have the same snoot and it's just as cute all right
let's get going
