Japanese Black Pine Second Styling

Bonsai Artistry
5 followers
#bonsai #bonsaiart #bonsaitree #natureart #miniaturetrees #gardening #plantlovers #homedecor #relaxingart #beautifulbonsai #treeart #bonsaimaster #bonsaicollection
This is how the tree looked back in 2022, before its first styling and after.
A few months later I squeezed it into a smaller pot.
Two years later with most of the wires removed and two candle pruning sessions,
the tree is filled with buds.
And this is the tree now, ready to be styled for a second time.
The very top of the tree is where I candle pruned below the node,
so that I get needle buds further down.
And even though I did get 6 of them, I did not get them as low as I hoped.
I'll start by removing all of the old needles,
leaving just the needles that popped out in August.
All around the tree, except the interior.
With the interior buds, and this tree has about 100 of them,
I am very careful of how many needles I'll remove.
I'm trying to leave a larger photosynthetic area on every bud inside,
than the buds on the exterior.
At the same time, I prune extra buds down to 2 buds per node.
These extra buds that came out in August, as much as 6 of them per node.
They did their job of reducing the energy distributed on every individual bud,
and thus reducing their elongation and needle length for this season.
Now they can be removed.
For a cleaner look, I remove the stems left behind from candle pruning,
as I work my way up slowly.
Finally we got some sunlight after 3 weeks of rain and snow.
I've worked my way up to the apex, and now I have to deal with the very top.
I remove the strongest by far elongated bud,
from the rest I remove the weakest that barely produced any needles,
and then the strongest left,
leaving me with 2 equal strength buds,
and a very weak that is a bit lower and thus not a tapered troublemaker.
I'll start wiring the first branch.
Since the basic structure is set, I'm mainly wiring the outer foliage.
At this point I have to note 2 issues that came after the first tiling of the tree back in 2022.
The first is the flatness of the foliage pads.
I did have the back budding needed to create full pads,
but they were not developed enough to offer volume.
Now they are, and even though my main goal is to create an exciting silhouette,
my secondary goal is to create volume in the foliage pads.
Something like this.
When a tree reaches this density,
I start to twist branches with laterally placed buds at 90 degrees,
so that one bud becomes an inner bud adding volume,
and the other becomes an outer bud contributing to the silhouette.
The second issue risen in 2022 that I will address with this tiling,
is that besides the lower left branch,
all of the rest of the silhouette was a monotonous curved line
that was good for a first tiling but somewhat boring for a finished tree.
Now I've got almost the development I need to create
some interesting shapes and lines for the outer silhouette.
Something like this.
And that is what I'm doing here on the left side.
Moving up, I reached the apex and not everything here needs to be wired,
just the ones needed to create the new nuances of the advanced silhouette.
Since I'm not planning to repot this tree this spring,
I remove the top of the soil that is filled with organic matter and debris.
Cleaning the top soil I saw that this root has no secondary roots going down,
so it's basically deadwood that should be removed all the way back to the trunk.
This root on the other side does have a secondary root going into the soil,
so I'll be careful.
I'll fill the top with two species of fresh moss.
And finally clean the pot with mineral oil.
Now, this is a beautiful tree.
Not perfect, yet, but almost.
Thank you for your time.
