I BOUGHT A WRECKED MERCEDES AMG GT63 & ATTEMPTED TO FIX IT

Ex Used Car
15 followers
80 Video Views·Feb 5, 2026
What's going on? We're on the Mark II channel and here is the Mercedes-AMG GT 63 S E Performance
V8 Biturbo. Right, we've got a clear and obvious goal. We've got to rebuild this thing and I have
just found out that there's only about 15 of these in the country and do you know why? There's loads
of Mercedes-AMG GT 63s in the country but the Mercedes-AMG E Performance there's not many and that's because these
were £170,000 new. So not many people ordered them because they thought well what's the point
in me having a plug-in hybrid when I just have the Mercedes-AMG V8 one? Rightly so. I didn't even realise
I bought the Mercedes-AMG E Performance. I think it was even listed as just the Mercedes-AMG GT 63 but £50,000 bought me that
which means this could be an absolute bargain. We have got damage on the rear quarter as well. We'll
sort this out. I've seen something interesting which is I thought I'd gather up in here before
we start doing some repair work. So this is this disgusting thing here is the plug-in hybrid part
so like you plug in and you charge it here like that looks really horrible but the way this hybrid
works on this is quite clever. So you've got the four litre V8 at the front and I think that
produces like 600 odd horsepower or so and when they're tuned anyway they make like 800 horsepower
when you tune them with like down pipes and remaps and everything like that but on the standard one
it then adds the hybrid motor which isn't attached to the engine it's just an electric motor on the
rear differential so all the weight is balanced so instead of having all your electric and engine
and everything at the front they put the electric motor at the back so it balances the weight a
little it does make the car heavier but at least it balances it towards the back then it adds a
load more horsepower to an already fast engine then gives you like over 800 horsepower in total
with the electric motor. Now imagine tuned this engine so like if this engine is like 600 you get
to 800 if we put like hybrid turbos on it down pipes on it this car could be well over a thousand
horsepower in a four-door technically hatchback I think that would be absolutely insane like so I
think that's the plan we're going to make like one of the fastest saloon cars there is on the road
it's only like 4,000 miles or so first we need to fix it then we'll worry about that the whole point
of the mark ii channel is so it's a bit laid back a bit more behind the scenes what we can do so I'm
going to hand it over probably to Matt and my dad whilst I go and edit the main channel video
on that dbx which has also got a mercedes engine in the same one we have just found out probably
not the same don't know so these guys going to strip off all the damaged parts then we can work
out what we need to order and there is a bit of structured damage inside the arch there and we
need to we've not done anything like that in that area before so we've got to try and work out how
we're going to repair that it's going to be a bit tricker it's going to be interesting but also
because there's not many of these cars on the road parts are probably going to be tricky to find
right pass the baton over to Matt and my dad and I'm here you're not Tony Tony's not turned up today
oh so they're subbing you in so I'm subbed in because Tony's decided he wants a day off at
least you can't make it any worse I guess the only way is up from here can only get exactly
so what do we need to start with we'll get this wing off yeah and then we can see what we're
all we can do is take bits off we can't break anything doing that surely
now you've said it okay brilliant let's just crack on let's do it
come across the first hurdle Matthew there's some bolts holding the wing on from
this way behind the door and to get to them you need the door open
can't open the door the second hurdle is there's two bolts that hold the wing at the bottom
which go behind the side skirt so we've got to get the side skirt off but to get the side skirt
off it needs to be on the floor without the ramp the wheels and that go on she's gonna roll baby
and now we should be able to open the door fully and get into here to take off the door because
the door blocks where we need to get to which is behind there which is really annoying so
door off let's do it okay so then we've got one bolt there one bolt there get this door off
there we go
now we should be able to get to the bolts so we can access this little black take this cover off
and actually reveal the bolts behind that
it'll be funny if there's no bolts behind here now there they are yes let's get them off
that's three that's three now we've just got to get this side skirt off get the ones from
behind there oh can you see them that's what stopping is then this wing can come off let's
get those off moment of truth if we've done this yes win right time to get the suspension off a lot
of it has uh decided to disconnect itself here which is good news for us but to see the damage
behind here we need to get all this off so let's get going what we've just found here look oh
that's like a rivolto size crack that is a rivolto size crack and this is on the front
disc as well that's £6,000 for that disc new or used no new and not quite as bad as a
rivolto but it's still bad isn't it yeah that's uh that's crazy it'd be better if it wasn't
cracked it'd be so much better if it wasn't cracked but unfortunately it's cracked so
it's gonna have to get replaced
caliper is off how was your first month of owning a supercar been do you know what it's been
unreal it's been crazy have you shown your nan it don't have a man
oh look all the way through oh oh it is like the revolver and it is not the revolver there's two
cracks on the back yeah that won't go again that's definitely not going to go again next job we want
to get this whole section away so we're going to undo the top wishbone which we found this
hopefully this one does but that's so tall okay plan b yes yes come on yes yes yeah she's coming
top arm is out next is to get this anti-roll bar drop link off what's my say mc skipper d
look how bent that is all right now the next thing we have to take off this lower arm
from the hub itself so we'll get that off this has made life easier because it's snapped
that's tight in it we've got the big boy out
the hub and drive shaft has come with it
how this should just pull there we go pulls out yeah so the next arms come off is this banana
looking one which isn't meant to look like that is it mark you well it is actually when it looks
on this end a banana looking arm it does have a crazy bend but not meant to look like that
not supposed to have damage like that let's get this one out one lower banana arm with the broken
end what's all this that is a lot of electric i've never seen that before going into the top
of a strut that's an airline isn't it that for the airbag this is an airbag this is like uh
so it's similar to the rolls royce i wonder if i can just disconnect that line one plug
two plugs airline what are you saying we're just going to disconnect it have you seen that prank
where like people go home to their parents and say like oh i went and paid 200 pound for air
do you know wheel mania's dad yeah yeah it's that good i'm gonna ask them if we can have the clip
and i can put the clip in the video i just went to the garage after work so i needed air in my
tires and he's just charged me 70 pound and he said it was special air what's the difference in
are you joking you said it was special air
i can imagine him flipping his lid as well because yeah he he does that we're gonna have to do
she's out now it's time for matt to come and assess the damage liam's taken off all of this
um most of that that is taken off in fact nearly all of it needs replacing this is the part that's
going to be the trickiest and we've not actually dealt with something like this before which is
interesting so this part of the chassis here look you can see it's pulled away
there now in such a tight space to work with and then it's going to require some welding and
everything so we need to make sure we get off all these hv lines um which i think is going where
are they going into this thing which i don't know what that is it's got something to do with calling
i'm going to call it the inverter i'm going to say that's the inverter i need to get this section out
and then when we get the new one if it fits directly in that's good news if it doesn't
we're going to need to do some more manipulating and bending but is this steel or aluminium yes
yes so it's steel so it's welded it's not glued and riveted all of this is this aluminium yeah
like the m5 so all of this is aluminium up here all of this is steel so we can do a lot of welding
that's going to be our main issue i'm hoping we can do that for now we still got some more
damaged bits to get off like the front bumper and then we can assess all the radiators behind it
let's get this headlight out
carbon fiber on the inside of the headlight as well wow that was the fastest headlight we've
ever taken out and then what's damaged behind here because i wonder if this this crash bar
is damaged what's scary is that on this bar there's a crash sensor here and um
no airbags have gone off should we disconnect the battery in case that blows off i've disconnected
the actual sensor okay let's get this front bumper off and then we can inspect what radiators we need
as well and get everything ordered before we start doing some messy welding and grinding
work back there let's go this ain't savable is it we need a new front bumper so the last
video that we posted there's at this precise moment there's 3.2 million people that have
watched that but there's only 2 million people subscribed do you know it's actually free as
well to subscribe people don't really like that do you think they're gonna know what subscribe
means or what subscribe during my dad when he was watching me like back in the day like when
it's just me on my own he never subscribed because he thought it would cost him money
why should they press the subscribe button i reckon if they press the subscribe button
we will keep rebuilding this car come out because the bracket's attached to the bumper itself
let's get it on there's gonna be lots of cables on it oh yeah it's a mercedes
oh look matt the floor's back look what's it doing you're not subscribed
this is what does the pedestrian protection oh the battery's still connected
so squeeze it no what these have is airline well it's just a rubber hose and it goes all the way
down here into this side yeah look you can see the sensor in there so what happens is if you
just have a small knock and you pinch that just a small pinch it blows a little bit of air into
that sensor and when it blows the air into the sensor it then shoots this explosive up here
so it'll go wallop up there push your bonnet up at an angle blow it off the hinge like there's a
little hinge bit there that'll blow it off it protects the pedestrian from hitting their head
on the bonnet and hitting the head on the engine because the bonnet goes up like that so then
they fly up and it cushions their fall and then what you have to do then is replace both the
sensors and these things and your hinges because of a pedestrian that's walked out on the road
they're expensive as well well expensive yeah they do them on bmw's a lot don't know
yeah mine mine went on my bmw what's that pedestrian
what's this as well got sensors on everything now isn't it can you drive this car in e-mode only
i don't know because i don't even know how do you do you think that's a speaker
for when you drive it in e-mode oh my god i think it is yeah
the bumper's off oh are they lights no it opens and closes this which is broken oh that's gonna
be that's gonna be well explained these flaps these wow look at that oh yeah i reckon they'll
close it close it when it needs to get up to temperature why not just have it open all the
time that's so over-engineered isn't it that's good that flappy grill motors are good flappy
grill bad this is a coolant for low temperature cooling and high temperature cooling what that
means i don't know and then there was also some parts which ran down here yeah these parts here
i couldn't work out where they were going looking behind the bumper i don't think there's that much
damage but i have just spotted something oh no so if you stand here yeah and look at this silver bit
yeah and then you stand over here and you look at that silver bit is that back i would say i have
ordered one of these because i did think it was it was smashed here they like forgot to paint it
look from here to here is black and then this they were like no i can't be bothered i think it's so
because the bumper you can see through so like you can see through but they're painting it black
where you can have a look through but there is all covered over by the actual bumper oh what
i don't think we got away with it that's definitely gonna be one of them when we
start putting coolant in and it starts dripping down now that means we've got to take off the
whole front get that right out and i think that's everything damaged off the car then
and we can actually start the rebuild process there you go one crash bar
can you get to this one oh this is the broken one behind here can we get this out
oh oh look it's all twisted it's all twisted up oh this frame's all broken anyway
so we're gonna need all of this
so we've got somewhere at least it looks really overwhelming and even i'm like oh my god how is
this going to go back together especially when you have a car like this and then a car like that
completely in bits of the unit at the same time hard not to overthink things but as long as we
do things one at a time and we tackle it one at a time we're good the main thing we've got
everything off damaged now there's a million and one radiators i am going to take off this aircon
but i need to degas the aircon everything is down here in a pile and i think what i am aiming to
tackle first as long as i can get the parts is this structural repair here which is going to
get really messy and i'm not sure really where to tackle it first we'll tackle this bit later because
it's not too much to worry about all of this because it's all bolt on bolt off parts it's
just very time consuming and working out where it goes that takes a little bit of skill hopefully
we get some parts in the next clip we got parts well a part this is the part that we need one
thing we are missing is this bar here i don't think anything is moved i think it is just the
bar that's broken but we do need that bar i was just worried that once we start fixing this and
then we go to fix up another one of those bars and it doesn't line up then we've got a problem
but i don't think that's going to be the case i think we need to get this in place there it's
going to be really tricky welding behind the back and also i'm scared of welding in there
and burning the carpet on the inside but i think now all i've got to do is make an area i can work
in and get all the damaged structural parts off so we can fit this section here i don't know if
it's actually going to work i know this is used for cordant hoses but why don't you like squash
oh it works no way yes one big caliper off here boy oh there's so much more room for activities
now aren't we we can actually see how bad it is it's pretty bad to be fair it's quite difficult
as well because you know like everybody watching this is going to repair this a different way
because there's no set way to repair it because every time a car crashes don't crash in the exact
same way that hose is absolutely mc skibbidy dented that needs to come off i want this whole
thing off i'm going for it here we go ground wire off this is the inverter what does the inverter
converts ac current to dc current power now yeah boy when we unplug this high voltage right i think
we should tape it up because we haven't took the we haven't took the high voltage pluggy thing out
but like i don't want to unplug that because if we unplug that on the revolso once you unplug it
you have to have coding to put it back in there's a procedure to tell the car let's put back in if
we can't do that then there's an issue i don't want to unplug it we're just going to risk our
lives and have a high voltage line dangling this is actually going to be live have you
oh my day yes yes don't touch that right i'm going to put some tape over it some electrical
tape you've got coolant all over your gloves and you're just holding two live wires the fact it's
orange makes it scarier like do you know if it was just like a black wire you'd be all right
this is called safety any main dealer watching this is freaking out right now look at that that
is terrible that's safety we just don't want to grind it or weld on it so there we go that
looks safe doesn't it that looks really safe bent bar they ain't sent us this by the way
did we order it yes and they sent me
where's that go oh okay i can see how they've got confusing yeah i mean they got bar okay
this will really tell us whether everything's straight like i can't see it not being but
what we don't want to do is all this structural work and then all of a sudden the bar goes to go
on and it and it's poking out here somewhere tony matthew who's your friend this is my dog
it's archie hello archie yeah he's not he's not he's not really the best dog in the world
well he's sitting down he's being a good dog there's somebody watching you as well
who's that behind you yeah that's that's the good dog that's a good dog that's um
yeah he's a nice dog he's the one that does everything that i tell him to do
he's the one that don't is he like matt and is he like your daughter
right that's off hey do you know what's funny even the merc guy who dropped off them parts
took a photo of this car because he said they're super rare that's for a reason obviously that no
one wants them probably but oh yeah it's had a proper wobble like that yes right so we need that
and all yeah all these little bits i've just bought some shares in mercedes have you yeah
is that because you got your gbx and you were like gonna be day trading
you're gonna be driving around in bugatti soon you're gonna move to miami only if the shares
go up so everybody out there buy a merc no you can't say no that's that's not how it works
yeah behind these shares everyone buys on them and then the person who told you not to buy
we know your games i know what you can call your course course yeah you can sell a course
yeah and how to trade you can call it tony's trades and then we can
yeah i don't think anybody's gonna buy it because i've not
earned any money yet so right we need that part oh my god look at that
where do you get these names from
what on earth is this and how did they figure out that they needed it
some call us three ways solenoid spaghetti junction are you being spaghetti junction
yeah i have yeah won't go again too close to birmingham see where that hole is there
on the angle yeah that's the same hole flat against the chassis if you're from bradford
you just leave it that you can't say stuff like that you might have fans in bradford
okay go now this is all welded on with you see these little tiny spot welds here and here and
here and everything all that but they're covered over the worlds are covered over with this
sealant so we need to get the sealant off so we can see the welds and then get it all the way so
i've got a sander uh we'll have a wire wheel it's gonna get messy guys i have noticed a bit of glue
like you see this little red bit here that looks like glue under it but it's definitely steel so
aluminium parts are glue and rivet steel parts they normally just weld but if it's steel going
to aluminium they'll glue let's uh get the magnet out and test steel steel steel steel steel steel
steel steel steel steel steel aluminium right goal to get that off i'll start there with the easy bit
and then work my way across this is a spot weld drill bit like you see it's got a little like
nub the idea is to just drill through the first panel and leave the second panel so we've got
something to hold on to we don't want a big hole then we don't have anything to hold on to let's
see what this does yep that worked that worked guys that worked great news great news let's
continue this bit was holding it now look at that so you gotta do that 100 million times now
all the way along there just for that little panel
one bit it's off oh that was about two and a half hours to get that off two hours to do that
my dad then used a belt sander to clean the surface ready for us to start welding the new
panel to it this part here let me let me set this up this is what it looks like without um if we
didn't know we think that's okay but we put this part in but you can see like this is fine where
it was or this is fine underneath uh but you can see the gap between there and there so i think
the wheels actually push that whole piece back including this panel here so this panel is just
a really really thin sheet of uh steel so we're gonna have to we're gonna have to take the carpet
out and then knock this panel closer to this so it'll meet up to it then we can tack it to it
people go oh that's not how it's done from the manufacturer but it is will be as strong or if not
the same as manufacturer because it's steel it can be manipulated and moved whereas something
like aluminium once you're bending that around it just snaps and it's no good where still you
can actually move it it's only the same as you pulling a dent out your rear quarter so you will
be all right but it's just trying to just get into that section in there i don't know what we're
gonna have to dig out underneath i'm just having a little feel around but i think i've seen how the
accelerator pedal and a bit of the carpet and then if we can knock that from the inside that
would be good i've been about three hours on this so i think i'm gonna have a shower and then get
back to it see you after the shower okay so i'm gonna crawl in here now take out the accelerator
pedal here i'm gonna take out this hopefully and then i can get some with a bit of space
and the carpet so i can knock out that panel to meet this panel i actually had to take off more
than a four i had to take off this plastic panel underneath the dashboard disconnect all the
electrical connections to that then the accelerator pedal had to come out which was just two bolts and
once i remove that i can start pulling the carpet away out comes the carpet which was very difficult
because the seat has got no power so i can't move the seat out of the way come out there we go
carpet out there's the bit that this is the part we need to hit but then
could also be further down as well but next step i'm going to try and just give it a little few
little love taps and see if i can work that bit of metal in there closer to our new bit of metal
and if it doesn't move i'm gonna have to think of plan b but let's see how we get on don't think
that's gonna work we're gonna have to bring it to it by probably screwing something into it
i think that's the next plan how old's that piece of kit tony you've been cheeky now
yeah if we could put that on and then put like a plate along the back of it so now i'm making a
plate which we're going to put on the inside of the car and try and pull it through from the
outside of the car to pull the panel straight again yeah i can see it here's the plan then
screw this bad boy on and then reverse hammer it chances of this working ready yeah i said i didn't
move myself i don't think it did move
no that's hitting it from that side i'm gonna hit it from this side see if we can
make the metal a bit flimsier yeah go on that's going oh oh
so we kept heating the panel hammering it pulling it doing everything to try and get
this panel back into place and it was moving slowly bit by bit that's close that's touching
now just that even tools started to break but eventually with loads of energy to use
we started making really good progress with it should we have to see if it fits
well that's a dream it's looking pretty good isn't it it's looking pretty damn good that
i think we're gonna have to uh clean the area so we can weld and then clean up all the edges
of this on the back drill the holes for plug welding it on you can get it on now this damage
here is classed as structural damage it's part of the structure so because of that the insurance
have categorized it as a category s and i can see that on the car vertical report all i had to do
is put in the registration plate of this car and i can see that the car got category s and when it
was crashed as well so you have different insurance categories like category n for non-structural
s for structural and you have b which is a complete write-off and it can't be put back
on the road it can be only used as a part car hence the breakers car on top of that i can see
all the mileage history of this car i can see how many owners it's previously had as well i can see
all the number plate changes a full timeline of the car and if it's ever been stolen imported
exported passed an mot failed an mot i can literally see everything just through the
registration plate of it and it works in over 20 different countries and on top of that if your car
was damaged and then auctioned off at a car crash auction website it's likely to show you the photos
of it when it was there which is pretty handy to know especially if you're buying a crash repaired
car gotta clean that up now drill the holes for that and then we can plug weld it but in the
meantime if you do want to check your car out you can do with the link in the description box below
and use the code for the mark ii channel mk2 for discount on that check let's get this welded on
just marking the holes now where i will drill for welding we've got some holes to drill
these are the really odd bits and the bits you probably see on the main channel
where it's like really goes really fast because we're like and it's on and then we panic because
we've got five minutes of footage for five days worth of work but i'm glad you're with us on this
structural journey of fixing this little panel here now because we're going to weld it we want
to clean up the edges we want to deburr the edges we want to clean up all in here because
the weld is going to go in there and like we need weld through primer else comment section will cry
this is etch primer but liam said that it's also suitable as welding primer as is very quick
drying so we're going to spray this on this stops it from rusting because obviously once you've
welded on to the car you can't spray the inside of the weld so i'm going to just give it a little
thing is it does make it harder to weld onto weld through primer because it doesn't stick as nice
but we don't want it to rust wait for that to dry and then we're going to start welding
oh what we can do as well afterwards which is going to be good we can get some uh wax oil
and spray it in there and that'll stop it from rusting from the inside out as well
which is good because it's in the wheel arch it's going to be a lot of water going in there
so what we don't want it to do is rust so tech screw just rolled it in somewhere
it's quite tight actually that's pretty good like it's all really close
now i've got a full world in all of these holes without setting fire to the inside of the car
so i think someone needs to be on the inside with an extinguisher see how we get on with the welding
been a long time since i've welded this could go terribly wrong you look like a welder when you're
you've got all your open arms like you don't care about getting on your skin
yeah you can't buy these t-shirts because i made it just thought
the battery's still connected on this car yep yeah we should disconnect it
because you shouldn't weld with the battery connected because you use the same ground
and that could absolutely mash up the deck aj shaser we just got a quick question
bye bob we are currently working on the mercedes
we couldn't get the battery disconnected so what would happen
if we welded with the battery connected there's a myth from years and years and
years back that it will kill your alternator or it'll kill your ecu
now i've been welding on vehicles for a long time and a lot that i've accidentally forgotten
to disconnect batteries a few times and has never had an impact even on a hybrid
i've never welded on a hybrid should we take the risk i'll take the risk i'm doing it
liam's in there making sure nothing it sets fire
you're a bit far away preferably don't spray it if it doesn't need to be sprayed
that one wasn't as cool you got it again
took my chin out
i need to get in there
where's the ground
on the floor
that sounded like it didn't do anything no i didn't
was it that i didn't do anything
what is that the last time you welded you say
look at that look at the quality of that weld that is top tier
let's see if that comes off
yeah it's not it's not hot enough is it
more power
that was off that was crazy
oh that's stuck though oh that's also stuck
can't say they look good but they're doing the job
so the idea here is to fill the hole with weld to stick the new panel to the old panel
but it might not look pretty but as long as it's doing its job that's what we're after
can you weld tony
yeah no helmet put the welder where you want it
strip your eyes
old school
have you ever had archive before
yeah twice
i can see how
what's it like having archive
it's like having sand in your eye all the time
how long are we talking what's gonna appear
about two or three days and then it and then
two or three days of sand in your eye
yeah proper man ain't I
should we test them
yeah let's do it yeah
let's test them
and jack the car up
i think you could jerk it up on that
i'm pretty confident that the welds have taken
now we're gonna make them look prettier
because they just look like an absolute wobbly mess at the minute
we're gonna neaten them up like this
nice and flat and then after that they will be painted and sealed so you'll never see them
so the idea here is then to sand the tops off the weld
to make sure they look nice and flush but i don't want to go too far
to the point where i weaken the weld that i've just done
cleaned up a bit now a bit of etch primer on the bare metal
again to stop the bare metal from rusting
somebody who was professional yes could do a better job
but we're not professional
next step is to seal it before we paint it
so seal this sealant here which looks a bit messy but it is still uniform
we're gonna try and get it as close to that as possible it never happens
same with the weld we tried to get the weld as close as oem
didn't happen
the thing is as long as it does its job that's all that matters
no one's gonna see this inside this wheel arch apart from every single one of you watching
it's just that it works
so what we learned from uh old jack not old jack but young jack in florida
you mask it up first and then that gets you the perfectly straight line that they've got
otherwise you'll never get that otherwise
so i'm gonna go i'm gonna go quite wide to cover over my welds
is that a weld that you've done there
yeah well that's quite close i am because that's like an oem weld
the thing is these oem welds are spot welds
the spot welds are like going like this like that right and then minor plug welds so
well like these ones are pretty close i would say
yeah they're like oem
that one looks really good
that is oem that's oem like don't you have your pay raise
it's called sarcasm tony
have you had fun doing this
yeah do you know like it is hard it is hard but when it's done at the end it's all right isn't it
like i like manual labor that's why i prefer doing this than sitting at a computer
what i used to do is sit a computer and uh just do stuff on a computer
and now i'm itching to do stuff like hammering like hammering
right now we've got sprayable sealer gray
specifically developed for today's automotive industry
a little does a lot see that that panel gap there as well
get in there lewis
right this one is just getting joined up
hi kevin
how did you know
so have you seen that clip on tiktok and it comes out of like that special nozzle
and just looks like that straight away and they don't even need to mask it
it's mad but i'm going to start peeling it
oh that didn't work did it that's a good line
yeah it's not actually that bad
i dare anyone before they comment and say i could have done a better job try and do it first
it's one of my better ones
that's one of his better ones
look over here look and this is with the proper tool
like that's how they've gone like they've gone crazy
it's not the job is for it to do its job not for it to look nice
but obviously if you're a robot you're going to make it look nice
but i ain't a robot
this is made like the krabby patty at spongebob square punts
what's the what's the place called
krusty krab
the krusty krab yeah made with love
painting time
now oem i don't really think they painted it
they had to go here and then they just gave up everywhere else
so we're going to try and kind of replicate that
absolute art attack
maybe i've painted too much now
it ain't looking anything like the other side
but it looks a lot better than what it did at the start of this video
i'm quite happy with that
it looks so different on the camera it looks a mess
but in real life it looks all right i haven't got contacts in
i was quite worried about that area there
but now that i've done it i feel quite relieved
but that was at least a day's work wasn't it
just doing that
i have seen something you've missed
oh what have i missed
oh that seal
yeah
so just to see they've sealed this here between the oem panel
and on matt's side that is not sealed
it will be in a minute
back to oem
that actually worked out better there
because i pulled the tape off whilst it was still wet
whereas when it was drying it was sticking to the tape
i'm absolutely i'm happy with that
looks really good
it's in position and structurally good sound
i reckon you jack it up on that
no problems at all
they should jack it up on there
next up i'm going to start putting the suspension in
i'm hoping i got all the parts
get to the suspension
first thing to go on is this thing
not sure what that is
remember to plug that in
move
now the hose that goes to the other pipe up here is this one
but that is well perished
so i'm waiting for that
so i can't install that yet
but that's that's fine
we can do that later
also the strut bar which goes from like over here to down here
not got that yet but that's fine
we can put that in later
i think i can put in this bar here though
let's do that
the bottom bit which goes on that bar over here is this thing
but i've got a suspicion that this thing is bent
because this bar which it bolts onto is also bent
so i've ordered that and that
so we'll save putting the bolt in for that for now
because i think yeah that's no good
next step this thing
which i also don't know what it does
i think it's the inverter
could be wrong though
oh this has had the electric plug plugged into it didn't it
okay it didn't die
that's good
right this inverter thing
well at least i think it's an inverter
is all in place
i'm not happy with the cable management
i'm not sure where it all went
now that's all in place
i need to get this
which is the broken part of the driveshaft out of the gearbox
and then we can start literally building everything up
so we're gonna start moving quick now
let's do it
there we go
broken bit of driveshaft
new driveshaft going in
in we go
there we go
a new suspension strut is next up
it's not springs on this car
really heavy car
air ride suspension
which sometimes can actually be okay
massive big thing
but as i mentioned with £14,000 in parts
on a £50,000 car
which actually we're doing all right
because the car brand new is £170,000
it's 104,000 miles
so £170,000 car for £64,000
we're doing pretty good at the minute
let's get this suspension strut in place
good work
next thing we're going to need is a wheel hub
to connect the top arm
the lower arm
the driveshaft to
and a few other arms which haven't yet fitted
over to the workstation
here is my workstation
so we've got the old wheel hub
old wheel bearing
all the gubbins that are on it
and the new wheel hub and new wheel bearing
i'm changing the wheel bearing
as long as the abs sensors as well
because if the wheel bearing has had a hit
and it's slightly bent or broken
it will cause the brake disc to like kind of wobble like that
and then if that's wobbling
and you put the brakes on
it could snap the disc
especially being a carbon disc
you don't...
it might...
you get away with it on a steel disc
but on a carbon disc not so much
so i'm going to change that
like i did check that on the rivolto
to make sure that wasn't the reason
why the rivolto is broken
but no it's just because of the impact i think
so this is all going to be changed over
i've interestingly seen these as well
these little like spaces on the back
where the caliper mounts to
and i imagine on the amg gt63
where you get steel brakes
i imagine the caliper is actually bolted directly to the hub
because the brake disc will be shorter
and then because you've got bigger carbon ceramic brakes
they bolt the caliper further away from the hub
using this spacer
because the disc is bigger
that's my only theory for that
bit of a kind of like ferrari lamborghini thing that
so let me transfer everything that's good off this onto that
and then we could get that on the car
let's go
they've not even tapped a thread in there from new
so that makes the procedure of changing over a wheel hub
a lot more expensive for someone that needs to do it through merc
we've now got to tap our own thread
fun
you guys have a look
there is supposed to be thread in there
there is absolutely none
there's none in there
i've just tapped the thread in there
but on this one
yeah the thread's in there
so you have to tap your own thread
just seems a bit odd
but bolts go in now
so uh i don't know
newer cars
we're getting stranger and stranger
and that is one new lovely wheel hub
ready to go on the car
so i'm hoping i'm gonna be able to lift this on my own
put it all on
connect that top arm
connect the bottom arm and drive shaft
and we should be looking
ignore that
we should be looking all good from here backwards then
and we of course we need the wheel arch and a few other bits
but come on we're gonna get there
that is all on and connected
just got to tighten up the top bolt
the lower bolt
and the anti-roll bar bolt
and then i could start putting in that arm
and the track rod end maybe as well
next step
front arm
it's just classic mercedes front arm
really big
no aero
just does the job
right this is gonna go in
oh this middle arm which i thought we didn't need to replace
definitely needs replacing
i've just noticed now from putting in that front arm
this whole thing seems too far back
so we're definitely gonna have to change this middle arm
because it looks like it's just kinked off slightly
underneath
let me show you
just under here
i know it's really difficult to tell
i think it's just kinked off slightly that way
that is annoying
okay so we've got a few bolts to undo
let's get this arm off
then we'll change it
three two one
i am so glad i'm changing this
i don't know why i tried to take a shortcut
it never works
you can clearly see the bend in that
and there's the new one
and there's the old one
look you can just see it's just been pulled back
and that makes sense
don't take the chance
just replace it all
why do i never learn
it's going in now
it is all on now
every single arm is new
new new
new new new
apart from this
which we don't have yet
because i don't know
i think i did order it
i can't remember
but it's not there
it's not needed right now
we're not going to drive anywhere obviously
up next is
break this baby
which was
so 14 000 pounds worth of parts i've spent
which was included the full front end
the structural parts
the suspension
and the majority of that cost
was this five thousand pound brake disc
which if we hadn't done that
we would have been five thousand pound cheaper
look at that daddy
wham
and it mad like this is held on with one bolt
and it's so expensive
interestingly as well
it's made by brembo
and brembo were the ones that made the rivolta one
which broke
yeah boy
next thing
caliper and brakes
we should have one complete wheel
looks like a banana doesn't it
right this is going on
there's some tools i've seen on tiktok
where like you know
you can have like a long
like it screws in like a stud
and it comes out like all the way to here
so you can pull the caliper off
and have it like hovering
so you can change your brake disc
oh that's clever
so you don't have to do it
i was like i want that for christmas
brake pad wear sensor going in
in that goes
and that bolts to there
so if you do take the caliper off
it doesn't rip it out
brake line going in
okay i don't want to go too tight
because now i've got to move this bracket over
and we'll tighten it all up
bracket going in
and let's route this cable
the brake line
oh and that is in
we just need the track controller
that was three days
three days of sweaty work
i might have looked like i didn't enjoy some of it
but now i've done it
i really enjoyed that
don't like yeah
it looked like maybe i didn't enjoy the hammering part
but looking back i did enjoy it now
so we've now got chassis
repair
in there
nice and hard
good work
we've got the suspension on
we've done all the hard gritty jobs
to be fair at the minute
we still got the interior spot back in
we've got like the body panel spot back on
the next job is going to be the front radiator pack
and get this car running pretty good
and then after that i think it's all body work
can't wait to see what this car's like
we're going to send it to the moon as well
we're going to put nine million horsepower through it
see how fast we can actually get it with that hybrid
but good start to the project
thanks so much for watching the mark 2 channel video
we've got an engine to build on the dbx next week
so i better get over to that now
thanks so much for watching
hit the subscribe button
hit that thumbs up button
and i'll see you in the next video
go grab some merch in the meantime
peace out
