Super PAK FA T-50 | Build Review | EDF Fighter Jet

Sixth Sense Aviation
1 follower
Jan 20, 2026
Check out the build review on the all new PAK FA T-50! This model is equipped with full 360 thrust vectoring for optimum maneuverability and performance, able to replicate aerobatics like the full scale version! All-metal shock absorbing landing gear struts allow for reliable take-off and landing. In addition, a simplified component layout and easy access points have made it easier than ever to run maintenance on servos, ESC’s, retracts, etc. Lastly, the beautifully engineered intakes, aerodynamic design and large wingspan allows this T-50 model to bring forth a great flying experience. Get ready to have some fun with the next 5th generation fighter!
Hello everyone, this is Alex with Banana Hobby and today I want to take some time to speak about a
very wonderful model that we have here coming soon. It's the PAKVA T50. Everything about it is
so great, the scale, the assembly, which is what something I'm going to be speaking about right now
because for a model this size, I feel that it's a pretty quick and simple assembly
to put this airplane together and get it flying as soon as possible. I know that excitement when
you get something new and you want to just have it flying right away, but you want to have it
flying right. So the assembly for this model is very straightforward and you can get this
airplane flight worthy just right about after you have everything set up and all the surfaces
are responding correctly and after you have your battery fully charged and all that good stuff.
So I'll be taking it out of the box right here to get it laid out on the table and show everything
in terms of the fuselage and main wings. Okay guys, so here's the T50 out of the box. Everything
that we need for the assembly is already here laid out, such as the fuselage, the main wings,
the horizontal stabilizers, and the vertical stabilizers I have them set down on the table.
Other miscellaneous pieces like the nose cone right here, and then the tailpiece that goes
over here at the end. Things like the short spars and then they actually give you a screwdriver to
put together the airplane too, but I'll be using my own. And also a glue or the rubber cement for
the airplane, which I'll be using epoxy as well, but that's also supplied with the box, the
airplane or the ARF version. Okay guys, so I wanted to go over a few things with the fuselage.
A couple of people had asked if it had certain features such as the actual full-size model,
and one of them were the leading edge controllable slats here at the very front
that are not available with this model, so they're fixed. And then there was two other things. It was
the wing root extensions here at the very front that are also controllable on the life-size model,
but are not available here on this scale replica. And also for the vertical stabilizers,
they're not all moving, so I have it right here. It's really just a separate rudder surface control
on its own, so they're not all moving like the real model. But other than that, I am really
amazed by how well the scale and appearance is to this RC version that we have here. It's a twin
70 millimeter, 2100 kV motors, and I'm going to see if I can get you a closer look on the fuselage.
Wow, this thing is big. So here's the top portion, and you can see the intakes, how they run
through the detail of the intakes on the fuselage at the very top here. Like I mentioned,
it's not split into two. It's pretty much one whole piece that's already put together
for you from the factory as an ARF version. We have the vertical stabilizer servos here,
the rudder servos, some decals on the engines, the nozzles here at the back, which are full 360
nozzles. I'm going to go in and actually, before I turn it over, I'm going to lay it back down on
the table. And if we take off the canopy, it's actually like a latch system, so you pull
and then you take this off, and this is where your battery will go over or will go on. So the battery
is going to be installed on this section. It'll make it a lot easier when you're trying to balance
the airplane. Turning this over, we have things like your nose landing gear here at the front,
your main landing gears, the hatch so that you can access your EDFs and motors and also the ESCs.
We have here one of the thrust vectoring servos that can also be accessed easily if you ever have
to make any changes or proceed with any maintenance. More thrust vectoring servos.
Here we have your elevator servos. And as you can see, it's all accessible through
just a couple screws and a top cover. Your main retracts. If you see here, this is actually an
access point for the compartment where most of the wires meet up. So it's all going to be right
here and this is where you'll have all the connections and your receiver and everything
is just pretty much here. So it's two separate compartments for the receiver and all the servo
connections and then for the battery as well. Very nice, very nice detail on the decals and
everything I see here. I'm pretty amazed by it. Here we have, these are the locking system or the
installation system that's going to be used when you're installing the wings together or putting
the wings together on the fuselage. This also makes it easier if you don't have enough space
because this thing is pretty big. If you don't have enough space to transport it, you can also
unscrew it and just simply pull off the wings and it all becomes just one piece like this,
just the way you see it. I got the right wing, same setup with the accessible servos.
They're covered by a set of screws and then the plastic cover here. Some decals, a flat servo,
and then the aileron servo. We got the rudders here. This is the right rudder.
Like I mentioned, unfortunately it's not all moving but you can get that pretty nice
cannon appearance on the vertical stabilizers. Also with the tail section, it's going to go
over here at the end and then the nose cone and then for lastly is the elevators.
I'm going to see if I can get started with the build just so you can see how simple it is to
put this together. Okay guys, I'm getting ready to install the elevator and I'm using a small tool
such as this screwdriver. It's not that wide and what I'm going to do with it is poke little holes
through so that they serve as a guiding point for the hinges. You don't want something that's too
thick, just really thin. The reason for that is because once you're installing these hinges,
they need something to catch on to and if the area is too wide, these ridges here won't be
as effective and they won't hold on too well. The purpose of this though is so that once you're
getting them in, they're guided through and they have a point to go through so they don't go too
crookedly. That's something that I've been able to work with and it seems to be working out
pretty well. It's all your preference. I'm going to do the same thing here on the fuselage
and I'm centering this area as best as I can so that when the hinges go through or when the
elevator is installed, it's all flush and nice. Remember, keep in mind that when you're installing
these hinges, there's a spar that runs through the elevator here so you don't want this to hit
or be in the way of the spar. Let me get a quick 5-minute epoxy mix going on, not too much. I just
need a little bit for the installation of the hinges. We're going to put that at the very tip
of the hinges. What this epoxy will do is it pretty much just serves as a way to keep them installed
and keep them in place so that they don't rip off. Also, the ridges that they have here work
as a great way to keep them in place as well. The hinges seem to be fine. Just get a little bit.
This comes down to whichever method works best for you. I'm going to put them in
on the elevator piece first. You don't want them too far in yet because they're also going to be
pushed in as you're pushing them in on the other end. You're just going to insert them
in the area or the holes that you made so that they're guided through. The reason you want to
keep a close eye on the glue is so that it doesn't seep in onto the joint where the hinge moves or
else it's going to lock it in place. That's something that you don't want. We got all the
hinges installed. Now, we just need to line them up with the fuselage. Perfect. Now, we're just
going to slide them through. Very nice. All right, so everything's lined up and it's all
moving perfectly. There's no binding. It's smooth. In a few minutes, the five-minute epoxy will
settle in and it'll just lock everything together. I'm going to get my push rod and I'm going to
insert it on the servo arm. We'll position it into place and then we'll get it lined up.
That pretty much does it for the elevator section. That seems to be the most complicated portion of
this build. Now that that's out of the way, everything should be a little much easier now.
Next, I'm going to move on to the vertical stabilizers and rudders. One thing I want to
point out is there's a section here that will be glued on for the rudders. If you notice here,
there's paint. I would recommend to have that sanded down to one, remove the paint and two,
make the surface here coarse. The reason for that is because epoxy, which is what I'm using
right now, will bind the best when a surface is not smooth but rather coarse. By removing the
paint, you're ensuring that the bond is happening between the two foam surfaces and not the foam
from one piece or one part and the glue from the other. I've seen many cases where wings have been
ripped off because this small detail was overlooked. Say for example, we did proceed with
gluing together this area with the paint being there, it's not going to be a good bond because
it's going to be the epoxy or the glue with the paint and you're just in risk of having that area
ripped apart because of the improper bond. Okay guys, so I'm about ready to start gluing together
the vertical stabilizers. I just want to point out one thing though. We have the surface here that I
sanded down. I did remove most of the paint but not all of it and the reason for that is because
I left the outer edge still with paint. That's because when I install the vertical stabilizer,
it won't look like I sanded it down and it won't be too obvious that some paint was removed
to glue it back, to glue it in place. So this looks a little cleaner because the paint here
is still at the edges. So I'm going to get this ready. Like before, it's a quick and easy five
minute half and half mix. The pre-installed control horn is already here in place
and you want it on the side with the rudder so it's looking good.
You'll also be using this piece that will be installed as a guider. So we're going to get
this glued on and just get that glue in there. This little spar that's going to go through the
end over here at the top. There's two areas and you want the smaller, sharper looking end,
not that it's sharp, but just kind of goes in. You want that going inside the piece,
inside the vertical stabilizer. We're just going to surround the outer area.
Okay guys, so I have the vertical stabilizer ready to be installed and I have everything
sanded down and ready. I have applied my glue. I tried to apply just a good amount
so that it's not too much but not too little either. One thing I want to point out is this
can be easily overlooked and try not to do that. Try to pay attention in this section where you're
putting in the vertical stabilizers. I have my glue ready on this point here, this part,
and then on the outer edges or these areas. There's one area where I didn't put glue and
that's where the servo, the rotor servo would sit under. In order to prevent any problems in the
future where the arm is somehow binding because of glue, I avoided that area. That's an area where
you don't want to put glue because there's no surface where this foam is going to meet with
the other end. So I'm putting that in right now and it went in perfectly. If you would like to,
you can somewhat shave off a bit of foam at the very top where the servo arm is located
because it does get kind of tight in there. I kind of like that but I might shave off just a
bit of foam so that the servo arm can have the proper movement but right now it's looking like
it'll move fine. I'll get the push rods installed and then try it then to see if it's necessary. It's
just something I'm thinking about but you know it might not be necessary at all. So what I did was
I applied the glue on this area where the vertical stabilizer meets with this plastic end right here.
I avoided or I omitted this area here right under the servo and then I continued to apply
more glue over here onto the edge. So everything seems to be sitting in. I turned the airplane over
so that we can get the main wings installed and this is a pretty cool feature because
if you decide to not glue the wings in place, you can do that by the way but it's totally up to you
because there's a system here that's in place to lock the wings with the fuselage. So these two
small shafts here will they'll run through these locking
points here on the fuselage and then we'll get these screw one screw on one and then the other
on the second piece here. Right now what I'm going to do is get the spar installed so that
we have it here and here on the main wing and on the fuselage. I marked it at the halfway point
so that it's even. After that we'll get all the wires hooked up and then we'll get the
mechanisms attached and this side should be ready and then we'll move on to the other side.
So starting off with the wing spar first. If you want you can also use some type of clear tape
as a marking point and also as a way to keep the spar in place. So in a sense it kind of
gives it some tension so that it doesn't freely move but it actually looks like it's a pretty
tight fit on the fuselage. Locking mechanisms are in. We got it in the fuselage. Okay and now
we're going to connect the leads and they've also are they've been labeled for you so
you just match the aileron with the aileron and remember that when you're connecting these pieces
all the polarities need to match so reverse I mean I'm sorry negative with negative
positive with positive and signal with signal. The spar is right at the center
and next we'll get these screws in place the second screw. There's several things that you
can try to do depending on how you're going to use the airplane and how you're going to transport
it and store it. It's optional but not you know it's not necessary but it's optional you can glue
it in place but just keep in mind that after you glue the wing it's going to be hard to take it
off so I'm leaving that as is I'm not I'm not going to glue on the wings because I'll be using
the locking mechanism which is just perfect and adequate to keep this airplane together.
For the connections on the servo leads you're also not required to do this but you can use special
locks to keep the harnesses together or things like a zip tie just so they don't disconnect but
it's actually really tight in place I mean they're not going to move around but like I mentioned it's
it's good to be safe. When I was installing the locking mechanisms I made sure that the main wing
was completely in so that the surface here was as flush as possible and it's looking great right now.
With the installation of the main wings this just leaves two final pieces
one being your nose cone which is going to go here in the front and I'll glue that in place
right now and the second being the tail section at the very end. For the tail section it's just
important to make sure that you have the right side facing up and you'll see that with the
finish on the fuselage it'll complete the panel lines. So I'm currently preparing the nose cone
so we can get that installed on the fuselage it's pretty much a straightforward procedure.
I've gone ahead and prepared the area where the nose cone will be installed
by sanding down any portion that had paint on it and making the surface coarse. Remember
that with this type of foam it'll bond best when the surface is when the surface is coarse
and not smooth and that's exactly what we have right here. The nose cone seems to pretty much
go in in one way but you still want to just make sure that it's in properly and that is exactly
what we want to see. The tail section is also pretty straightforward there is no paint on this
and we'll get that in just like that. I'm in the process of setting up all the wiring for the
system for the airplane and I will be connecting everything to the receiver but
one thing I wanted to point out is that this is your retract sequencer that comes with the
airplane so you have one lead coming over here which will be going into the what's it's coming
from the servo that's required for the door opening mechanism here at the nose landing gear
and you'll notice that two are connected like this where it's the polarities are matching and
the other one is reversed. For the landing gears this section doesn't really matter that much
because say if if the main landing gears were coming in and retracting while the nose was
extending that means the nose was in reverse or opposite from the main landing gears so in this
case the lead has simply just been reversed and that'll sequence all of them together so that
they retract together and they extend together. One other note is that I have my front nose
my nose servo lead here and that's set up just as you can see here and and it's important to
make sure that both of them all leads are connected from the main and front landing gear
and the servo lead also going into the sequencer so that everything sequences properly and also
responds correctly. On my receiver I'm using the stock 12 channel radio system receiver that you
can purchase separately or as an option you can obtain it with your ARF package. Even though
there's 12 channels I really only used eight because from the manufacturer everything has
already been connected through a series of wire harnesses so for example the external BEC it's
also running with the throttle lead so here channel one is my aileron and it's already
labeled as well so aileron channel two is my elevator channel three is my throttle
channel four is my rudder and steering system from the nose landing gear and then channel five
my main retracts and front retracts running through the sequencer that I just showed
earlier channel six my flaps channel seven and eight my thrust vectoring. Another important
thing that I don't want to leave out is that the ailerons and the elevators are
hardwired together so they're mixed intentionally through the Y system or the Y splits so on one Y
split you'll have one going to the aileron and then another going to the elevator so that would
be say for example channel one and then channel two one Y split is going to one aileron and then
the other one to the elevator it's crisscross. I have the airplane turned over and ready for the
power-up procedure this will use three I'm sorry two three cells in a series cell stock it comes
with the bullet connections and to set this up I will connect the negative lead from one battery
and the positive from the other I will also be shifting the batteries accordingly so that I can
match the proper CG so let's get this connected in series all right so two three cells will
obviously make up a six cell battery here okay so now we have two extra or two last ones
two final leads and then two coming from the ESC we'll connect our positive together here
perfect and the last negative connection here you'll notice a spark that's perfectly normal
there's a pretty good amount of voltage running through the system okay so I have it turned over
and just a quick response that looks that looks great very nice okay guys so that pretty much
wraps up the build review for the PacFa T50 here at Banana Hobby as you can see the build process
wasn't too difficult we got it here assembled in a few minutes so the only certain points that you'll
probably have the most complication with is installing the horizontal stabilizers but
everything else everything else goes together smoothly the wings are detachable through the
wing locking mechanism where you can either you know unscrew it or screw it back in place
if you have any other questions about this model since it is an upcoming model or any concerns
about it we do have a technical support text line where you can send in a text message I'm
actually answering questions that we get there throughout the day and I would be more than glad
to help as always thank you for watching
