Making Folded Bowls - Origami Method!

Ceramic Art Studio
35 followers
Jan 18, 2026
Hi everybody, this is Anne. I know that you guys like the hand building projects,
so I thought I'd design some dishes for you to make. At first glance they appear complicated,
but when I show you the steps you'll be surprised at how easy the projects are.
My first step was to roll out a quarter inch clay slab. I'm using two quarter inch thick rulers that
I got from the hardware store to gauge the depth of the clay with. I just keep rolling and flipping
the clay slab until the rolling pin rolled flat against the rulers. I then like to smooth out and
compress my clay using a rubber rib both up and down and side to side. I created this template
for the project and needed to cut out three of these. I used my needle tool to cut with. I created
the template so that the back side of this slab should be the same size as the rim of this plastic
party cup. As this project looks better when all three of the template pieces are symmetrical,
I'm going to use the party cup to make sure my cuts were accurate. I just set the cup down over
the back side of the clay slab, then used a wet finger to work the clay ends down. Then I can
smooth out that top sharp edge. Next I want to bevel the flatter portion of that template. I can't
get my bevel tool down in that crevice, so I used a needle tool held at an angle to do the job.
I then folded the tail portion of the template upward and folded the tail inward over the beveled
edge that I just created. I scored, slipped, and attached the tail in place and worked a coil along
the inside to make sure it stays put. I then scored the beveled edge with my needle tool.
I repeated these steps for the other three template pieces. When they were all completed,
I placed one of my used pieces of plastic wrap down to do the construction on. I then placed
the three circles on the plastic with the folded edges in the very center and the taller edges
overlapping the lower sides of the circle that it's butted against so that they interlock. What
you're looking for here is to get a triangle in the very center. The scored edges are tucked under
the slab that's covering it, and you want to make sure the circles are symmetrical and the raised
edges are the same height. The next step is to create a cone-shaped piece of clay. I fit that
down into the center hole and worked it into the bottom and the walls to connect all three of the
dishes. I started with the blunt end of my needle tool, then switched to a paintbrush to make it
look seamless. Once the clay hardens to leather hard, you can do a final cleanup of the area.
The way the clay folds upward and together creates a nice triangular shape in the center,
so I bent those flaps inward a bit to accentuate that shape. Now remember that scored area hidden
under the raised flaps. By pushing down and applying pressure along the top slabs, I can
connect the two pieces together. I'm doing this to all three sides. To make sure I have an even
better seal between the slabs, I placed a coil under each of the raised flaps and worked it into
the seam using gentle pressure so as not to distort the clay. Note that I'm working the
coil down over the edge and in between where the two discs meet together. I repeated this with each
slab. When all the coils were all smoothed down, I placed a thick piece of foam down on my flat
table surface and placed the shamrock on top. Right now the slab discs are flat to the surface
of my table, but I want them to be rounded into ball shapes, so I'll use my wet thumb as a sort
of push plate to the center of each disc. This will stretch the center of the clay downward and
the edges that are still supported by the foam will remain upward. The clay will be lifted off
of the surface and into the little bowl shapes. I then accentuated the lift by using my fingers
to lift even more along those outer edges. I repeated this technique on all three of the shamrock
petals. I'm sure you're asking what to do about the back side of this piece. This piece is still
a bit too wet to really deal with, but ideally I would wait for it to dry the leather hard, then
turn it over and work the raw edges smooth, adding little bits of clay as needed. Now here's one that
I finished earlier. I used the underglaze on top of shaving cream method to decorate it. Now here's
another version I experimented with where I swirled the edges inward. I painted the inner triangle
with red underglaze, then glazed the entire thing with Amaco C11 and fired it to cone 5 with an
8-minute hold. Jim and I had a lot of fun using these with our flavored salts. Let's do another
origami bowl. This one's even easier than the first project. I started with another quarter inch
ribbed slab. Now I had this hexagonal wooden push plate to use for this project, but you can just
download and print out a paper hexagon if you prefer. I simply cut the hexagon from the clay
slab. Again, I'm going to do the construction on a piece of plastic wrap as I'll be moving it later.
I created this little template that fits along the hexagonal corners for my next step. I fit
the template along the first corner and using an exacto knife, I sliced up through the thin side of
the template about three quarters of the way up. I repeated this step for each of the six sides.
I bent each of the edges up with the tails positioned inward, almost pointing to the corner
beside it. Using my needle tool, I marked the new positions of each tail, then scored the slab and
under each tail. I wet and attached each of the tails initially with my fingernail, sealing the
joint. I then reinforced all the joints with small coils. If you need a more secure seal, you can also
place coils behind each of the tails as well. I again placed that thick piece of foam down over my
work surface and moved the flat plate on top of it. I used my thumb to press down in the center of the
slab, which lifted the edges of the plate into a little bowl like the first project. You can then
play with the edges to get that nice flower shape. Now as I didn't place a coil behind each of my
tails, I used a wet paintbrush to slake together those connections. Remember to place the plate
back on the table and make sure all the raised areas on the rim are level to the table. There it
is on top. I just finished firing it. Again, I used the underglaze swirled in the shaving cream method
to decorate the plate with the Amaco C11 clear over the top and fired it to cone 5 with an
8-minute hold. Oh, it looks so cute with the little Hershey kisses in it. Who can resist those? And
they look so elegant on a dinner table filled with condiments, dipping sauces, or even just a spoon
rest. Thanks to the newest members of our Little Street Pottery Research Facility team. If you'd
like to join the team and earn a title, click on the Super Thanks button or the link to buy me a
coffee. In any case, we invite you to subscribe to our channel and we'll see you next time in the studio.
