2026 HOYT Alpha AX-3 29 New Tuning System DEEP DIVE and Test!!!!!

The Precision of Crossbowry
1 follower
1 Video View·Jan 11, 2026
2026 HOYT Alpha AX-3 29 New Tuning System DEEP DIVE and Test!!!!!
Comments are disabled for this video.
Hoyt Alpha AX-3. Hoyt finally enters the tuning game where you can tune this bow without needing
a bow press. Hey everybody this is PJ Reilly from Lancaster Archery out here to tell you about the
2026 Hoyt Alpha AX-3 29. That's the model that I have here. There will be an AX-33.
Main thing you want to know about these new bows is the new XTS tuning system and stay tuned
because we are going to take a deep dive in tell you all about it and show you how it works.
All right Hoyt Alpha AX-3 29. I'm going to start off. I don't know why this is. It is called the
AX-3 29 but it does measure 29 and a half inches axle to axle. Go figure. There is also a 33. AX-3
33. That's a lot of threes. So but this bow this of course is the aluminum lineup that Hoyt has
for this year and we're going to have on this bow available peak draw weights 50, 60, 65, 70, 75
and 80 pounds. Know you guys out there who want that 80 pound you love it. Now for our cam we are
returning with the HBX Gen 4 cam. This is a cam that Hoyt had last year as well. It's a four track
cam and what we're going to do is the total draw length adjustment for this bow AX-3 29 is going
to be from 25 to 30 inches. Now you're not going to get all those lengths on one cam. What Hoyt
does is they have one cam, five different modules and so the bow that I have right here there are
four module positions that peak at 30 inches. So those module positions we have quarter inch draw
length it's going to be 30 inches, 29 and three quarters, 29 and a half, 29 and one quarter.
So you're going to have those four position on each of those five modules. That's Hoyt's way of
keeping that efficiency up. You know if you went from 25 to 30 inches the lower end of the module
your efficiency is going to be nowhere near as good at the top. By having just that basically
it's three quarters of an inch adjustment you're keeping that efficiency higher at all of the draw
lengths. Also what we're going to have here of course we have the Picatinny rail machined into
the riser. Hoyt is the originator of that so they have the Picatinny rails machined into the riser.
We are going to have IMS dovetail for your rest in there as well. We're going to have two bushings
here for your stabilizer. One is going to include Hoyt's vibration dampener. You can move that
to either place if you want or actually you can see how much that sticks out there.
It kind of acts as a stabilizer in itself just in that position but you can configure that
however you want. So the big news with the Hoyt 2026 series of course is the XTS tuning system.
Let's get into it. All right so the XTS tuning system new system from Hoyt there. What we have
are basically you're going to have controls. There'll be a lock and a control on each of the
four limbs. That's important to note because you're going to be working with all of them
and what it is is they use a series of wedges. One wedge in each limb that as it drives in it
affects the cam position. So that's what you're going to use in the tuning process
as you're paper tuning your boat. All right so what are we looking at here?
So first off before we do anything we're going to look at these lines that we have. We've got one
two three four five I believe. I'm blind so I can't see. One two three four five six we have.
You're going to see these six lines and you're going to have a little triangle right here
on your lock. So you're going to notice that there are two long lines at the bottom and two
short lines at the top and then there's two in the middle that are the same length.
When you bring this triangle into the middle between the two lines that are the same length
consider that zero. So if you start messing with things and you're like I want to go back to square
one start all over let's go back to neutral. What you're going to do is you're going to adjust this
so that your triangle is in between the two lines of the same length. That's zero. Now so let's say
we're shooting through paper we want to tune this boat. I shoot through and I get a knock right
tear. In the old days Hoyt used to have the yokes on the limbs here so what we were used to is okay
I get a knock right tear what I'm going to do is put twists into the right take them out of the
left that's going to shift the cam to the right fixed. So we still want that cam to go to the
right with the XTS but the way we're going to do that is just to keep things simple and still be
talking right to right right tear we want to move to the right however got to turn the bow around.
So now what I'm going to do I'm going to work with the right limb which is actually the left
but it's right as I'm facing it. I'm going to undo the I'm going to loosen the lock screw
right here and I'm going to turn clockwise that drives the wedge in and so what that does is it
puts pressure on the limb tip here which causes the limb tip at the back to come up. I put let's
say I put a turn in let's just keep it simple a full turn in here I want to take a full turn out
here by taking it out this side you can see I'm relaxing pressure so this end of the limb
is coming up and this end of the limb is going down. So again what I'm doing by driving in here
and out here is I'm turning it this way which if you flip it around that causes the cam to go to
the right. So that's so we are still doing right to right but again we've been kind of used to
working from this side of the bow. We're going to stay right to right but we're going to work
from this side of the bow now. Now it's important that you know if you do a full turn here that you
take it out here because if you go uneven you're going to affect draw weight and we don't want to
do that. If you want to keep draw weight the same you just have to counteract whatever you do here
over on this side. Now you can also you know let's say it's a pretty significant tear
if you don't want to go crazy just working up on the top you can also go down to the bottom
and so obviously if I drive in this one I can drive in the bottom as well then you're going
to take out from the top take out from the bottom. That's still gonna you know as you're doing the
process you have to figure out which you need to do. Now one of the unique things about XTS is
Hoyt engineers worked on this for three years because they wanted to not only fix
horizontal paper tuning issues they also wanted to fix vertical and we can do that with XTS.
So let's say I have knock high you don't want to go through well maybe you do but if you don't want
to like me go in and cut off your D loop retie everything you know because knock high I want to
bring my knocking point down so the way you can fix that with XTS is I'm going to remember knock
high so we want to lower the knocking point so I'm going to let's say take a full turn out of
this side take a full turn out of this side same thing this is fixing vertical whatever I do to
this one I'm going to do this one so I'm going to take a full turn out full turn out now I'm
going to come down to the bottom I'm going to put a full turn in each side and what that's doing
again I'm increasing pressure here which pulls the limb tip this way decreasing pressure up here
pulls the limb tips down I'm relaxing here so the limb tips going down so if the top is going down
and the bottom is going down what's my knocking point doing it's moving down as well and now one
of the unique things another unique thing with XTS is Hoyt says usually when we talk about tuning
we fix vertical issues first and then horizontal Hoyt says to do the opposite fix your horizontal
first and then what they found is sometimes if the vertical is just a little bit you may fix it
once you start playing with the cam position up here you may end up fixing your vertical issue
in the process so you may not need to do you know you may just take care of vertical so they say
fix your left rights first then go back and shoot again see if you're still having that
knock high position if so then you can make your equal adjustments to bring that knocking point
down all right so here we are with the Hoyt Alpha AX3 29 and we're going to put that XTS
tuning system to the test now but we're going to put it into use now I want to make sure Hoyt you
know gets credit where credit is due you may not have to use this system at all this bow when I
took it out of the box I eyed up my vertical you know rest and knocking position and then I set the
arrow rest to 13 16 so my arrow the center of my arrow is 13 16 from the riser it shot a bullet
hole but what fun is that we have a new tuning system so I slid the rest over to about 11 16
so that I could get a tear in paper and now we're going to use
XTS to fix it even though the rest is not technically where I would want it
the slightest bit knock right I moved the rest to the right so produced a knock right tear
so we know the fix for that loosen that one remember the bow's facing me I'm working with
the right I'm going to do a half turn in to the right I'm going to do a half turn out on the left
as we know the net effect of that from this position should be the cam went to the right
let's take a shot actually still a little bit knock right let's do them all right well let's
go to the bottom let's see what that does so it's still facing me so I'm working with this one
let's do a half turn in the bottom half out all right let's shoot again bang now that is
in the middle we're in one shot two shot three shot right there all done with the XTS tuning
system even with my rest technically not where I want it I was still able to use XTS to tune it to
good shot all right Hoyt Alpha AX3 29 shooting experience what's it like shooting this bow so
this is aluminum so it definitely feels different than the carbon let's walk through the draw cycle
here so effort at the front end coming back super rock solid at the back wall let me let down here
something I got into this year where I had to let down twice on a deer so some of the some of
the bows can be rough on the let down this one at 85% let off it's usually 90% where you get
into trouble 85% let off for me to let down is not bad but I have it on that extra hard
draw stop the position at the back end there and man it feels like a limb stop
super solid at the back wall nice deep valley so going back several years I was not always a fan
of the Hoyt cams this is going back six seven years ago this new HBX Gen 4 this is my favorite
Hoyt cam just because it just draws nice holds nice it's got a deeper valley than I'm used to
or not that I'm used to than they've had in the past and this thing just points great what I
wanted to do you notice I don't have a stabilizer on this one I wanted to see what it's like
using just their vibration dampener you know it's got a little bit of weight out front that's
probably two ounces just wanted to see what that feels like because you know there's more and more
people who want to go light you don't want to you know if you're bow hunting in the back country
I did a hunt uh this year caribou hunt where I was doing up to 10 miles a day on foot don't want
to have a heavy bow when you're doing that and that was in the arctic so I was on flat ground
at elevation it's even worse so what it's like shooting with with only that vibration dampener
as a stabilizer you know it's staying upright this is a 29 and a half inch bow so that would
be one that I would expect maybe to be tippy but it's not just with that little bit of weight down
there keeps the bow upright aims well as I mentioned that back wall I can pull hard into it
nice solid back wall they have there good shooting experience you know Hoyt has one of
the stiffest risers out there because of this bridge in the back here tech riser they call it
and that just adds a ton of rigidity you definitely feel that when you're aiming
speed test Hoyt Alpha AX3 29 let's get our draw weight 70.8
speed rating is up to 340 feet per second 70 pounds 30 inch draw 350 grain arrow
we have matched all those specs let's see what we get 332.4 334 split it call it 333
767 feet per second off the speed rating Hoyt Alpha AX3 29 80 yard clay bird challenge
let's see what we can do no stabilizer just the vibration dampener let's get it down
just under it or over just under oh it's like touching the bottom of the clay bird
I think if we were counting lines that would score
oh there it is broke the clay bird but it stayed together I don't know how that's possible
yes I do know how it's possible dead center of the clay bird didn't break it clay bird still there
though Hoyt Alpha AX3 29 this baby can shoot all right take a look at that dead center on the clay
bird I had actually had a pre-drilled hole in there we got this new clay bird holder I didn't
know how it was going to work and I went through the pre-drilled hole if you've any ever seen
anything like that leave a comment below if you want to comment about what you think about a shot
like that leave a comment below hey but I'm just a small part of it Hoyt Alpha AX3 29 awesome
shooter there's also of course the AX3 33 new colors Georgia red clay if you want to see everything
that's available in these bows be sure to click the link in the description below if you like
this video give us a thumbs up if you want to see more videos like it subscribe to our youtube
channel don't forget to click that bell to get notifications wherever we put out new videos
as always if you have any questions you can visit us at LancasterArchery.com
