Narrated glassblowing, full process, murrine color pattern ruffle vase

Art Creation
8 followers
Hey everybody, welcome back to the studio. Today we've got a pretty long process video for you
where we'll be making one of our larger marini pieces, but let's go ahead and get started.
We're going to start by getting a small amount of clear glass out of the furnace.
This furnace inside that door is about 2,000 degrees and it stays on 24-7.
It contains all of our clear glass.
Now we're going to head over to our garage and we'll go ahead and pick up this bundle of glass
that I've put together and preheated. Right now it should be right around 900 degrees.
I want it to get a little bit hotter before we transport it to our bigger oven on the other side
of the room. So we're going to pick it up, make sure it's nice and stable, and then we'll preheat
it over the flame before we move it over to the bigger heating chamber. Right now we're just
getting our color pattern ready. We're going to end up stretching this big bundle of color
pretty far. I want it to be probably about four feet long, maybe five feet in the end,
and then we'll be able to use it to create our color pattern which we'll make our piece out of
in the end. So right now all of the canes are held together by these little wraps of wire that
I have around them. So what I want to do is I want to heat up the glass so that everything fuses
together, and then I'll be able to cut away the metal and we'll have our nice cylinder that we'll
begin to start to stretch. All right, so now we've gotten rid of all of our metal and everything is
basically fused together. One of the problems that we run into whenever we start to stretch
this and melt it down is that in between all of the individual canes we get lots of bubbles which
we really don't want. So what I'm going to do is I'm going to roll this on our metal marvering table
many many times and really try to smooth it out and push all of those bubbles out so that I have
a nice solid cylinder of glass. Tilt it towards me. Yeah. We're going to push all those bubbles
back towards the clear. We've been chopping at BJ's. There you go. Yep. It's on Davis. It's where
the old Sears was. It's a Sam's Club type. All right, so now we have everything melted together.
I pushed out as many bubbles as I can and we're going to prepare to stretch it. So my brother has
a small bit of glass he's taken out of the furnace and we'll attach this to the tip and use it as a
handle so that we can stretch our colored glass. Yeah, that's perfect.
Ye olde stringer. All right and now that it's at the right temperature I'm going to pass it
off to him at the top of this ladder. We'll stretch it and then we can put it in our annealer
so that it can cool off. Sam, could you do me a favor and grab the annealer doors in a moment?
Thank you. We're going in a three. Come on, man. Hands on fire. Golly. Thank you. All right. Thank
you, sir. Appreciate you. Oh, if you go in there, but so it's the next day and we've come down to
the studio to check out what we got and here's our color pattern. So we've got these long links
and essentially what I'm going to do is I'm going to chop them up into little discs, maybe about a
quarter of an inch thick, and then we'll be able to use them to make our color pattern for the
piece. And here's our wet saw that we'll be using to chop this stuff up. Basically this is a diamond
blade where it has water cascading across it the entire time. So I can run my glass through the
diamond blade and it will chop straight through it. Whenever you're cutting glass you have to
make sure that you have water cascading across the piece non-stop. What that's basically doing
is it's moving all of the tiny little bits of glass that are being cut out of the way. If they
were to stay there and pile up, we'd start to build up heat and then a piece would eventually
break. And now that it's all chopped up we can lay it out on this pastorelli plate and you'll
begin to see the pattern that our piece will have in the end. And here we go, this thing's all good
to go. So we're going to put it in the garage, the same thing that we put it in whenever we were
heating up the merini in the first place, and we're going to then transport that over once it's
preheated to our reheating chamber and start to turn it molten. Glass the middle and we'll start.
Inside of our reheating chamber the burner that creates the heat is on the right side,
so we continuously have to flip it back and forth so that the entire rectangle of color can get
evenly heated. And then once it's hot enough we'll begin to squish it to try to eliminate
all the gaps in between the discs. Class together. I'm just saying that because I get paid.
Give it a flip. I want to go down the river soon. I think that might that might be a fun day you
know. So that's pretty good. All right so now everything is fused together. I can take a small
measurement and I'll begin to make my collar. So I want this round little piece of glass that's on
the tip of my pipe to be about as round as it is long that the piece is so that it can roll up into
a nice cylinder around my collar right there. We'll make sure that they're both a good heat
and then I'll come over and we'll roll it up into a cylinder. So that went really well. I'm going to
brush off any residue that kind of stuck to it and then we'll try to line it up so that it's a
nice even cylinder. Try to make sure that you can't really see the seam where I put these two
pieces together. It's a social experiment mixed with survival skills. Totally. And then there's
Yeah I bet. There's a show called Nathan For You. There's this dude named Nathan Fielder
and he's just like a ridiculous person. Like he uh he it's like a big prank show kind of
but basically. So even though we squeezed it pretty well on the plate it still has lots of
holes in between. So now we're going to start to eliminate them. You can kind of see here that lots
little pieces of fire are coming out of those holes. It's a good way to tell where the holes
are. It's a pretty funny show. So now we got it hot and we're going to try to push from the inside
with our jacks tool while we roll on the marver. We'll repeat this process quite a few times until
the outside is quite smooth. Tough one dude. They're having a party and these like ghosts
show up or something. What? Really? Yeah because uh. That's awesome. Okay cool. All right and now
that we have it nice and smooth we'll do something similar that we did with the marini where we're
going to cap it off with a piece of clear glass. The reason we do this is because now I need to
close off that cylinder so that it creates a bubble on the end of my pipe. I want to maintain my
pattern so we use the clear glass for the termination so that I can cut it off using the
clear and I don't lose any of my pattern.
Other movies. Yeah it looks like it has to do with uh. I want to do plunger pickups too.
Give me some air Luke. You can go on. All right so now at this point in the process everything's
looking pretty good. We're going to let this cool down. You can really start to see the color
and now what we're going to do is we're going to go and get a new layer of clear glass on top of
it and we'll begin to make our piece. Really? For like a special? And while we're getting this new
layer I just want to ask that you guys subscribe to the channel if you're not already subscribed.
You know if you like what you're seeing, like the video, leave a comment, share this with someone
who might find it interesting. I really appreciate everything you guys do for me. So now we have that
new layer of glass and we're going to start to smooth it out and really cool it down. I made sure
to cool down my glass before I went into the furnace so now we need to heat the core back up
while we cool down the outside. And to do that we're going to use one of these wooden tools
called a block. I have different ones at different sizes but they live their lives in water
and whenever the water comes into contact with the glass it creates a bit of steam that moves the
glass instead of the wood burning away. And now we're going to get ready to go in for another
gather. I want another layer of clear glass. So I'm going to cool it down, inflate it slightly,
and then we'll head to the furnace to get the next layer. And like I said before this furnace
is at 2,000 degrees on the inside. It houses 700 pounds of molten glass, only clear glass,
and we keep it on 24-7. So now I'm doing what's called a strip gather where I get rid of all the
excess glass by kind of just going vertical. You can really see the core there and all this
glass is going to ooze off and I can kind of choose whenever I want it to stop. Can you grab
the 14? And now I've got another one of these block tools ready. This is our 12 block. It's
one of the larger ones we have and it doesn't have a handle on it so I've kind of kind of
hold it in a strained position but it still works. Works great. Burn my hands. You got to
keep on moving. Keep on moving. That's all good. I'm going to throw it down in a second.
So now we finally have all the material that we're going to need and we can start to inflate it and
turn it into our final piece. So this table that I'm rolling my glass on is called a marvering
table. It's a thick piece of metal that we use to shape the glass as we roll it back and forth,
but it also cools the glass down. So I cool it down in the areas I don't want to expand and then
when I hang it over the edge I can blow through it and all the areas that stayed hot and it didn't
cool down will start to inflate. You've probably seen me use this tool quite a few times. This is
our newspaper tool. So this thing in my hand is about 12 sheets of newspaper wrapped up and soaked
in water and just like the marvering table it really helps me cool down the glass in different
areas while I get my brother to inflate it from the other side of the bench.
We're making like a big cylinder base. Should be like a bottle in the end I think.
Give me some light air. No I'm gonna we're gonna make a cylinder. We'll heat up the top and then
I'll try to pull it out long like that. That's why I want it I want to have a lot to work with.
It might end up being pointy but I want it to be a nice bottle shape if we can. You can go.
So now we're getting ready to put in what we call the jack line. I've given the pipe to my
brother and he's going to heat it up quite a bit and when he comes over we're going to use our tool
the jacks, these big tweezers, to put a small incision right off the tip of my pipe. This will
be where we'll break the glass once we transfer it to a different pipe a little bit farther down
Oh no. No then I had two tracks. You hear that? Yeah you can come down. Give me some air.
Yeah on. Off. Okay you're gonna turn for me. Yep give me some air. On. Oh I'm getting a blister.
I'm gonna turn this for just a second. I'm gonna take all this crap off. Yeah see blister.
Turn in the pipe. Wider pipe. Yeah.
Something I've heard other glassblowers say from time to time is that if you can manipulate the
glass without actually touching it with your tools that's the path you want to take. So a
lot of the time I like to heat the glass up and let gravity kind of give me the length that I'm
looking for so you can tell the bottom half of the piece is a lot hotter than the rest of it
so I put it vertical and it'll start to stretch. Can you give me some air? On. Maybe a blow hose?
Yeah I think so. Long lines when it drops you know so it's like.
So the piece that we're planning on making is going to be cylindrical
so now we're going to start to put the bottom on the piece. I'm going to use my tools to make
sure that the sidewalls stay even and my brother has some wooden paddles he's going to start to
press in on the bottom and give it that nice 90 degree angle that the bottom of a cylinder should
How's it look? He was like in college he was like with them when they started.
Who are these guys? They're the uh. And now it's time for that transfer I was talking about earlier.
This is what we call the punty transfer. This solid pipe with the little bit of glass on the
tip is what we refer to as a punty. It's going to be the new pipe that we use to start to open
up the piece once we break it off of the old one. So what I'm going to do is I've stabbed my piece
on my punty rod onto the bottom and I made sure that it's directly in the middle of my piece. I
want it to be as symmetrical as possible so now we add some water and I'll pull the moil the little
piece of glass overlapping my pipe up onto the rail give it a tap and then we're off. Garrett
this is my mom. Have you met my mom before? Garrett's one of the ceramic instructors. She's
a good friend of mine. Say again? Yep. And now what I'm going to do is get rid of a small bit
of glass off of the tip of my piece. So this is called trimming. I'm going to elongate it a little
bit. That lip there has some tool marks on it that I really don't want on the final product. So we're
just going to get rid of it. We're just going to cut it off. Yes. I'll flash and come back out and
we'll do it on the next one. Hold on. Hold on. Let's cool it down a little bit more. I'm worried.
Yeah last time I didn't lift off the rail. I was trying to be I was trying to be fancy.
All right let me take a flash. And there we go. So no more tool marks. You know the lip of the
piece after you do the transfer is often very very thick so it's good to get rid of that even though
it doesn't have any tool marks on it. And now I'll start to use my other tools to lift it open and
inflate it from the inside. It is even so freaking normal to pass on top. Yeah wait a minute.
So we were trying something a little bit new on this piece. What we were planning on doing was
making a bottle. So I'm pulling all of this out so that we can make a nice neck for our bottle.
Right. But often in glassblowing things don't usually go as planned especially when you're
trying new stuff. So it's difficult to expand and try new things a lot because things will
constantly break on you. You know if you haven't had the practice of trying the new form. But it's
always good to branch out and try new things. You know there's nothing wrong with it. And things go
awry you know sometimes. But that's life. That's kind of just what you have to be ready for in
general. All right take a flash and then bring it back to me. Oh no. Okay.
So the move didn't go exactly as I planned. The glass got pretty thin and it fought me. I don't
know if I didn't get it hot enough or if I didn't apply enough pressure correctly at the right time.
But it's off. It's not what I want. So basically what we're gonna do is we're gonna get rid of
everything that I just pulled out. So we're gonna get rid of everything
basically from the neck down. That sucks.
No fun. I hate getting rid of it. All right whatever. Let's do it quick. Yeah I do.
What do you mean you don't have to? All right you ready? Do it. Do it.
And there we go. So we're basically back over to where we were a few steps ago. Which is okay
because now we're gonna make it into something different that's a little bit more unique.
Let's see what happens. So now I'll use my tools to start to open up the lip.
This is a little mangled. It's a little bit uneven. So I'm gonna do this in a few steps
but we'll open it up slowly so we have something kind of resembling a cylinder.
No that's okay. This thing's all over the place. Yeah not what I wanted.
Okay I got it. I don't even know what to do. We'll flare it. So now what we're planning on doing is
heating up the lip and spinning it very fast so that it flings out with this centripetal force.
Now I'll hang it down. Let gravity kind of pull it down a little bit and we get this kind of floppy
lip shape. We make pieces like this in the hot shop quite often. Usually it's a bowl that has
this kind of lip and we call them floppy bowls. So it's kind of got like a floppy kind of lip to it.
Looks really cool. Very abstract. You know and the lines just really pop whenever it gets thin
like that. So I'm very happy with how this turned out in the end past all of the kind of bumps in
the road. So now the final thing we have to do is disconnect it from our pipe. So I'm going to take
a small squirt bottle and I'll apply some drops of water right where I want the piece to break
so that it really really wants to crack there. We just cool it down. Then I'll take a small wooden
paddle give it a little tap and it'll break off into my brother's Kevlar gloves. We use a small
torch to get rid of any sharp spots on the bottom and then quickly we'll transport it to our annealer
so that it can cool down overnight. Can you go this side? The middle or somewhere? Yeah you got
it. You got it. Awesome. And here we go. This thing came out great. You know the marini pieces are
fantastic. They're always a bunch of fun to make because you always get something different you
know. The lines move and kind of resemble the motion of the glass so you can kind of tell
where it was stretched and where it was thinned out in different areas. And you know the lines
are kind of like proof and evidence that that happened. So I always find them very interesting.
They're always a bunch of fun to make and you always get something new every single time.
This piece is also available for purchase either on my website or my Etsy page so if you'd like
to have it in your home check out the link in the description and hopefully you can. And again a big
thank you to anybody who made it this far in the video. You guys are the best. I can't tell you how
much I appreciate you. And we just recently launched a Patreon page so please check that out if you want
to help support the channel and get some extra content. And here is a list of all of our Patreon
friends so far. Y'all are the best. Thanks so much. Be safe out there and I'll see you in the next video.
