The X1 Pro and Max now have a new cycling mode, an indoor follow mode, dolly zoom,
find my drone and much more with updates to manual flying modes, beacon and joystick.
In this video I'm going to explain the main aspects of all of these and test whether or not
they're any good. And please stick around to the end because I'm also going to have a test of the
new manual features, the extras and the firmware. But I'll explain how to download and install the
updates in the right order which is really important. And why am I doing this on a cycling
focused channel? It's because I think the X1 Pro is simply a fantastic way to capture your cycling
adventures. The X1 Pro has been my go-to drone for content creation since I was sent it to
review. Now at the start of 2025 there's been a host of firmware updates which have brought
several new features to the X1 Pro and Max. If you can't see the new flight modes in the app,
check this button and then make sure you have activated those features. We'll go through them
now. Cycling mode is almost the same as the existing follow mode except for one key difference.
You can specify whether you're in an open area or on a narrow route. The choice makes little
difference on a straight course like this because it's designed for a winding path.
On the open area setting it flies a direct overview course whereas on narrow routes it'll
follow your pattern more closely. This is how the difference is shown on the Hover Air website
with the narrow routes following the cyclist track more precisely.
I've ended up testing this several times on different bikes in progressively more confined
areas culminating in this one. I brought my mountain bike to an area that is so congested
with trees and the passage so narrow I would normally not even think about flying a drone here
but if we set it on cycling mode on narrow routes and keep it close we'll see how it does.
I think it does well. There are trees either side of this single track and if you watch my movement
the X1 Pro gets to where I have been and then does its turn. Looking back at the footage I
think it's doing a very good job in a challenging environment, one which I haven't ridden in quite
a few years. Well as you can tell I've not done this for a while. I'm going to add the beacon now
and see if that makes much difference but I'm impressed so far.
If you connect the beacon rather than your phone it supposedly gives you a better connection to
the X1 Pro. You get a video screen and you can see what that is showing. You can put the beacon,
you can clip it to your jersey or there's a handlebar mount which I'm going to use.
In the first few of these beacons there were clearly a few problems and mine didn't work that
well but Hoverair seem to have that sorted now because this one works great. As we'll see later
you can use it to take emergency control and it has another trick on its upper sleeve.
I think that was a really tough test for cycling track on its narrow route. It definitely works
best if you have it close to you and on a flat shot. I think anything higher or further away
runs a risk of a crash. If you're finding this helpful I have just one request. Could you watch
until the end please? That's all that YouTube now seems to care about. Give me a thumbs up as well
I suppose that helps too. Thanks. So what if you do crash? There are now two find drone features.
The X1 has hit something but a great thing about having the beacon running is that as well as being
able to see what the drone was looking at I get this screen which is part of find drone. I'm in
the middle it shows me which way I'm facing or walking and I can home in. So it says it's seven
meters eight meters so that says I am less than three meters from the X1 and wouldn't you know
it's right there. You can also find your drone using your phone screen. To be fair the map
is not particularly detailed but what is useful is that blue field of view
because I'm clearly walking back up towards it as I get nearer and there it is right in front of me
and that works as long as the battery stays in your drone and the drone stays powered on.
Dolly's zoom might not be immediately obvious as to what that flight mode is. It's a specific type
of effect that is done in camera usually where the camera moves in at the same time as it's
being zoomed out or vice versa and it creates a kind of vertigo effect with the focus of the
background suddenly changing. Probably the most famous is in Jaws in the get out of the water
scene. I was looking online and I found this explanation of Dolly's zoom. What exactly is a
In short a dolly zoom is a shot that uses a combination of camera movement and shifting
focal length to stretch or compress the background and in the X1 Pro this is how it looks. It does
the shot by flying backwards and electronically zooming in. You can set how far and how much to
then it flies back in so you have two versions of the shot. The new indoor follow is a close
mid shot only version of cycling mode with a narrow route but it doesn't like sharp turns
and I had to go very slowly for the X1 Pro to follow me. The whole thing felt rather hesitant
but we have a small cottage in the Scottish Highlands in a more open indoor environment
if that's not an oxymoron this could work quite well. You can show off your crib man.
Just before the next one I'd just like to say a massive thank you to the people who support this
channel who have become members. These are the names of my production crew and adventure crew
as they're called. If you'd like to find out more just click the join button below any video
except if you're watching on an iPhone and then I'll pop up and explain everything. Right next one.
Updating the X1 Pro firmware is straightforward it even talks you through it. The firmware
downloads to your phone then uploads to the aircraft. It's the next steps you need to do
in the right order to successfully use either of the manual extras. I have the beacon and joystick
combo both need separate firmware. First connect the beacon to the X1 Pro or Max because this is
where it draws the firmware from not your phone. It should recognize there's an update and if not
there's a drop down menu on the beacon screen as we will see. After the beacon updates connect the
right hand joystick controller. Here I had to look for the update that's the red dot and select it
in order to update. Again your phone isn't involved and once these are both updated you're good to go.
With the beacon alone you can now take emergency control. There's a handlebar mount and a clip
mount for a jacket. Now with the beacon you can perform an emergency stop and take very
limited control of the X1 Pro's movements. I can move it forward and back so I could get it out of
trouble if there was something close to me or I could move it away and with this one I can bring
it down. I'll just go put my hand underneath and land it. So clearly this is not designed for
routine flying but it is a useful thing if you've got this clipped to your jersey or you've got it
on your handlebars you can quickly take control if necessary. The single joystick control is probably
my my favorite. Put the right hand part of the joystick assembly on the bottom of the beacon
and now you've got a single unit to manually control it. There's a button on the back and
pressing that allows you to use your action to send the drone forwards or backwards, side to side
and then the joystick on the top gives you the up and down control. So from there to go forwards
to go left, back, left, right, down, up, bring it back to me, down. In this configuration the gimbal
control didn't work for me but you get the idea. With both joysticks in place this is what it looks
like. Looks like a proper controller. You could just view it on the beacon's screen but you can
also add your phone as an even bigger viewer. So let's get this going. In this configuration the
X1 Pro has many of the features of other drones. The gimbal tilt is on a wheel by the left fingers.
So this is it flying in full manual and it flies just like any other drone really. It's neat,
you can see what you're doing and I quite like it. That's my cable by the way, it's not the one that
came with it. The thing you don't have with this is the sort of DJI quick shots. You can't put a box
around something and then track it when you're flying manually, or at least you can't in my
experience. But they're updating the firmware all the time and this video could be out of date by
the time you see it. However I can see no way of changing the camera exposure. I would usually
underexpose by a third of a stop. I could add neutral density filters, sort of sunglasses for
the lens, but these seem too dark, more suited to bright snow. That's something I'm sure Hover Air
will be aware of and will be changing. I accidentally gave the X1 Pro a very tough
cycling test just after I received it. I wanted to see how fast it would follow me downhill.
And the result? Well I couldn't have done it again if I tried. Could I ask you to take a
look at that video please? You will find it here.
Thumbs up if you enjoyed this one please and I'll see you again next time.