The Art and Science of Copper Raising

Arts and Design
68 followers
#art #decorate #design #diydecoration #sculpture #ceramic
This demonstration by American mixed-media sculptor Lynn Whitford was initially recorded in 1986, taking the form of an audio cassette and a batch of 35mm slides. We recently digitized both in our lab, then edited them into a simple 20-minute video that details the basic process of raising copper, magically turning raw stock into objects of stunning and graceful beauty. The tools and fundamental techniques are clearly explained, and many budding artists over the years have been introduced to the medium by this presentation.
A number of Whitford's pieces appear near the end, and you can see recent work at her website:
https://www.lynnwhitford.com
Angle raising is one method of making a hollow form from a flat sheet of metal without the use of solder.
In these slides you will see this flat sheet of copper become this piece.
The extent of explanation given assumes you have worked with metal before, but not done any raising.
Tools which you will need beyond those which every metal studio is likely to have are
Hammers, including a leather or wooden mallet, a sinking or blocking hammer, a raising hammer, a planishing or ball peen hammer,
a stump with a large hollow carved into it, a variety of sizes and shapes of steel stakes, depending on the size and shape form you intend to raise,
a large torch for annealing, and a pickle tank big enough to pickle your piece.
It is possible to raise a disc as small as several inches in diameter, or as large as several feet.
But for your first raising, something between 6 and 12 inches starting size would be a good idea,
as both very large and very small pieces are difficult to hold onto.
18 gauge is easy to use, and copper, which is what you will see being raised in these slides, is the easiest metal to move.
The first step is to draw a profile to scale of the form you intend to raise.
Making a heavy paper cutout of this is useful, but optional.
Measure the length of the outside of this profile with a measuring tape or a piece of string.
To raise a symmetrical piece, you start with a circle with this diameter.
With a center punch, make a shallow indentation in the center.
Scribe a circle the proper size with dividers and cut out the circle with the metal shears.
Thoroughly anneal the disc and pickle it.
The first stage in the hammering process is called sinking or blocking.
For this, you use a sinking hammer and a depression in a stump,
beginning at some point on the outermost edge of what will be the inside of the piece,
that is, the side without the center punch mark.
Sink the metal into the hollow, rotating the piece slightly after each blow,
working your way slowly and methodically to the center of your piece if it is to be round-bottomed,
as the one I am about to raise is.
If your piece is to have a flat bottom,
before sinking, you must mark a circle on your metal the size of the base
and sink the piece only as far as this circle.
Throughout the raising process, you will keep this area more or less flat.
After one course of sinking, anneal, pickle, and repeat the process if necessary
to get a gently and evenly curved bowl form.
This one, shown here after two courses of sinking, is ready for raising.
The piece must always be annealed and pickled well after every complete course of sinking or raising.
Also, before each course of raising,
you should pencil in a series of concentric circles on the outside of the piece,
one half to one inch apart or so, using a compass and your original center punch mark.
These will help you to work the piece evenly.
The most important thing in raising is to use your head.
If you think about the principles involved,
you will be able to figure out what you would have to do to get the metal from here to there.
And after that, it is a matter of intelligently placed hammer blows on properly supported metal.
Raising is basically a process of compressing.
If you start with a disc with a circumference of 20 inches
and raise it into a bowl whose circumference at the rim is 10 inches, for example,
and you don't stretch out the metal in the process,
the metal near the top of the bowl obviously has to be considerably thicker
than the original gauge of the blank.
This compression is produced by supporting your piece at an angle on a stake
and driving the metal down to the stake just beyond the place where it is supported,
point A in the diagram.
On the other hand, if you hit the metal at the point where it is supported, point B,
you will be pinching the metal between two pieces of hard steel,
and you will be spreading it rather than compressing, and you will get a bump.
Choosing the correct stake is very important,
and you may have to change stakes several times as the form of your piece changes.
Even on a relatively simple form,
these are standard raising stakes, which are good shapes to begin with.
For a round-bottomed piece, you use the rounded end, point A,
and for a flat-bottomed piece, you use one with a sharper edge, point B.
For a very large piece, especially when you are working near the outside edge of the metal,
you may need a stake which provides more support, such as this one.
What you need to think about in choosing a stake
is that its curve needs to be quick enough in both directions
to allow your metal to compress onto it when you raise,
yet not so quick as to provide no support for the piece.
If it is too flat, for example, as is stake A in the diagram,
you will stretch the metal with each blow.
And if it is too sharp, as is stake B,
your piece will be difficult to support.
Your piece will move, and you will get no compression.
The raising hammer has one relatively sharp face, and one which is flatter.
You can raise with either end.
Since the force of your blow is concentrated in a smaller area with a sharper end,
this moves the metal more easily, and sometimes you need to use it.
On the other hand, it scars the metal more,
and when the flatter end works for you, you may as well use it.
Any imperfections on your hammer face will be transferred onto your piece,
so keep it clean and symmetrical.
To start raising, support your piece with your left hand on the stake
near the center for a round-bottomed piece,
or just below your first concentric circle for a flat-bottomed piece.
If you are left-handed, you'll have to put the working slides in backwards
and reverse the directions.
Choose an angle which doesn't require you to compress the metal too far with each blow,
since you should maintain the same angle throughout the complete course of raising.
Each successive hammer blow should be adjacent to the previous one
as you rotate the piece around in one direction to your starting point.
Be very careful to maintain the same angle all the way around.
Then move the piece so it is now supported on the circle you just raised
and begin the next circle.
This row should slightly overlap the first one,
and you should revolve the piece in the opposite direction from what you did on the first row.
The reason for this is that if you always turn it in the same direction,
you are likely to put a twist into the metal,
which will be very obvious if you ever raise a piece with a seam in it.
The angle of your hammer blow is also important.
If your hammer strikes more or less perpendicular to the stake, as in Figure A,
you will get the most compression.
If it strikes at an angle, as in Figure B,
you are more likely to stretch the metal as well as compress it.
There are times when you may want to do this,
for example if the metal is getting too thick to move,
but try not to do it by accident.
In general, you will want to stretch the metal as little as possible.
The last circle in each course of raising requires special consideration.
Because the metal is unbounded at the top,
it is very subject to stretching and thinning,
and may flare out instead of compressing properly.
Some people use a wooden mallet,
which compresses the metal better for this round.
If you intend not to rim your piece,
nor to cut off any of the top edge,
it is very important to keep it thick and regular.
At the end of each course,
you can thicken the edge by placing the piece on a sandbag,
or on your lap on several thicknesses of towel if it is large,
and hammering along the rim.
If this causes the edge to crease,
you can smooth it out lightly against a stake with a wooden mallet.
When you have finished each full course of raising,
the piece should still be symmetrical and evenly curved.
Now anneal it, pickle it, and draw on your concentric circles.
If you find that you bit off more than you could chew
in choosing your initial angle of raising,
and your piece has a profile like this,
you should repair the damage by starting your second course of raising
at the point where you lost the angle,
and raise the top end to match the bottom.
It may take you very few courses of raising
to get where you are going if your form is shallow.
This one has been through two courses.
The farther in you raise it, the more difficult each course becomes,
because of the thickening of the metal,
and sometimes because of the difficulty of finding a stake which works.
When the raising becomes difficult,
it is often because you are having difficulty
supporting the piece securely on the stake with your left hand.
Using your knee to support the bottom side of the piece
is often very helpful,
or sometimes even using your legs or feet on large pieces.
Here you see Japanese people using their feet to support their work.
Every raising shop should have a variety of stools to sit on,
from six inches high to the height of the stake and its bites.
But since they often don't, you will have to be inventive,
piling up slabs of wood, sitting on tables, inverted boxes, and so on.
Here you see the piece after four courses of raising.
If at any point during the raising process
your piece becomes asymmetrical, or develops bumps or ripples,
be sure to fix it right away.
Sometimes a partial course of raising can fix a problem area.
Often your best remedy for hammering out ripples or bumps
is a mallet or hammer with your piece supported on the wooden stump.
Should your piece develop a crack at any time,
it is necessary to repair it at once,
or it will continue to split as you work it.
These are more likely to occur on the edge than elsewhere,
from too much stretching.
The best remedy is trimming the edge to below the crack,
but if you can't spare the metal, you must repair it with a hard solder.
Cracks or holes within the piece, which occur very rarely,
must be soldered also.
Here the piece has been through seven courses of raising.
Don't forget how much you can bend a copper piece by hand when it is annealed.
Minor asymmetries can often be fixed that way.
Copper is a very forgiving metal,
and will allow you lots of leeway in backtracking and undoing errors.
This piece has now been raised to its final form,
and is ready for the next process, planishing.
Planishing is a process of truing up the form,
removing the raising marks, and smoothing the metal.
By raising, you compress the metal,
but in planishing, you will place your piece directly onto the steel stake,
not at an angle to it,
and thus when you hammer, you will be spreading the metal slightly
as you pinch it between the two steel surfaces.
As in raising, you need to anneal and pickle the piece
after each complete course of planishing,
and to pencil in the concentric circles on the surface with your compass.
You can probably planish on the same stake or stakes you used for raising,
but now you will switch to a planishing hammer,
or the peen end of a ball peen hammer.
It is particularly important in planishing
that the stake and hammer face be clean and smooth.
Likewise, the piece should be kept clean.
Planishing is generally done in concentric circles,
from center to rim, as is raising,
but it is useful to do a pre-planishing course called bouging,
in which you planish lightly and with more widely spaced blows
back and forth across the concentric circles
to true up the form a little
before you begin the real systematic planishing
around the concentric circles.
Planishing blows should be light
so as not to stretch the metal too much.
Use very regular overlapping blows.
If the lighting is good,
you will be able to see each facet you make.
The sound is also very important for correct planishing.
Proper planishing produces a mellow sound,
which you will learn to recognize,
and planishing on an improperly supported piece
sounds hollow or tinny.
It is a very slow process,
and you may have to anneal the piece
and re-planish many times before your surface is perfect,
if the raising marks are deep.
This piece only took two courses
because it was raised cleanly.
The final round of a course of planishing
requires the same care as it did in a course of raising.
Care must be taken to prevent
excess stretching and splaying out of the edge.
One way to deal with it
is to planish from the inside
with the piece supported on a clean, flat anvil.
In any case,
the hammer blows should be very light.
Each course is followed
by hammering the edge to thicken it
if that is the kind of finished edge you want.
If you don't need to solder
any additional elements onto your piece,
it is good not to anneal it
after the final planishing,
since it has been work-hardened at that point
and is very sturdy.
Once the surface is well planished,
your piece might be completed,
and at this point
the lesson on basic angle raising is finished.
However,
you might hardly have begun your piece
depending on where you want to go with it.
For example,
here is what became of the piece
you just saw in process in the slides.
I inverted it
and cut a hole in the bottom,
which then became the top,
trimmed and sanded the original top,
now the bottom,
to make it flat
and soldered a base onto it.
The entire surface was then filed
with a large bastard cut file,
and a spout was constructed for it
and soldered onto the top.
Later,
it will be further modified,
patinaed,
and will be one element in a still life.
Other possible modifications
to a raised and planished piece
are shown in the following slides,
adding rims and or bases.
Adding handles.
The dark ones are forged iron,
the light ones forged white bronze.
Adding a spout.
You can raise a symmetrical form,
fill it with a special kind of pitch for support,
and hammer it into an asymmetrical form,
as I did with this tall copper bottle.
You can alter the shape on different stakes
once the piece has been raised symmetrically.
In this case,
the alterations would be made
between raising and planishing.
Pieces can be cut up and reassembled,
etched, patinaed,
and modified in numerous other ways.
As a beginner,
you will have to experiment
with hammers, stakes, and techniques,
as there are many ways that work.
Just remember that logic and accuracy
are at least as important as strength,
and you will be able to figure out
your own methods.
Even if you never do any more hollowware,
having experienced the process once
will make you very aware
of the way metal can be moved,
and you will be able to apply the same principles
to any other metalwork you do.
