⏱ • Timecodes: 0:00 - Introduction and discussing the importance of preparing clay, (wedging) 0:50 - What shape to make the wedged up balls of clay 1:23 - How to sit at the wheel properly 1:41 - Positioning of left arm, the 'anchor' 2:02 - How to slam the clay down effectively 4:21 - How to position left arm and push upper body weight onto the clay 5:10 - Water/slip usage 5:36 - Using little finger to seal the base of the clay 6:00 - Introducing vertical pressure 8:01 - The centred shape I'm after 8:26 - Scraping the ball of clay if it feels gritty 9:02 - Discussing the speed of the wheel 9:53 - How to position hands as to not grind your skin 10:32 - Pinching fingers and focusing on stability 11:18 - Using the leftover 'skim' of clay to help stick down the balls of clay 11:37 - Coning the clay 13:50 - How to remove your hands from the clay as not to introduce a wobble 15:20 - The importance of centring
Centering the clay is the cornerstone of throwing on the wheel. It's the process that must be done
before any pot can be formed and the aim of this video is to go over that process in exacting
detail alongside discussing many of the tips and tricks I've learned over the years. It begins of
course with clay but more specifically it's the wedging of clay which is important for throwing
but I've already made a much more in-depth video about that which I'll leave a link to on screen
Simply put, this is the process of kneading clay into its one even texture throughout and void of
any air pockets that might lie within and these irregularities will only make the centering and
throwing process more difficult which makes it a step you don't want to skip as learning to center
can be difficult enough already as a beginner. The first thing we'll discuss is the shape of
the lumps of clay used to throw with. You want them to be regular, ideally with a rounded base
so when thrown against the wheel it doesn't trap air beneath it and with either conical
tapering walls that lead up to the top or perhaps more easily for a beginner you should pat a well
wedged lump of clay into a ball shape like so. What you don't want to use is an irregular shape
like this as although you can center lumps like that as a beginner it'll be far more difficult
so make sure the lumps of clay you're using are well wedged and regular in shape and now the
First thing you want to consider is how you sit at the wheel. You don't want to be too far away
from the tray or the metal wheel head. Instead you want to scoot your legs forward so they're
around it and so your head, when leant over a little bit, is more or less directly over the
top of the lump of clay. I then take my left arm and I shove my elbow into my torso and then I just
lean my upper body weight forward slightly onto that arm to stabilize it. What you don't want
is both of your elbows up in the air like this as you're trying to center as they aren't braced
against anything so instead I tuck my elbows into my waist and I lean my upper body weight forwards
onto them. The first thing we need to discuss though is attaching the clay down to the wheel
head. Like we spoke about earlier it helps to have an even round shape that's thrown against the
wheel. This way no air can be trapped beneath the clay when it's slammed down and you can see just
by placing it roughly in the middle how centered it was. Compare that to this irregular lump which
even when placed in the center spins and wobbles on the central axis and you'll see when I try to
center a piece like this how difficult it can be to center as those undulations slap into your hand
as the lump spins around and for a beginner this can be quite difficult to control so don't use
lumps of clay like this and instead patch your balls of clay into spheres like so or at least
into a shape with a rounded base and a conical top. Now the obvious first step is to throw the clay
as accurately into the middle as you possibly can and to slam it down firmly this way it sticks
onto the metal and one thing I do is use the rings that most wheel heads have in order to tell if the
lump of clay is in the middle because as you spin the wheel you'll notice that the lump of clay will
probably have a larger gap on one side as compared to the other and all you need to do to remedy this
is to push the clay away from where it's closest to the line until the gap between the clay and
the line is more or less the same all the way around. At this point you can even pat the lump of
clay into shape a bit to get it as centered as possible before you begin to add water to it
and begin the process properly. Initially attaching it very firmly is crucial though and what you don't
want to do is slam it down onto a surface that's already quite wet as the lump of clay just won't
stick to it properly so ideally you want a dry wheel head and a dry lump of clay otherwise this
is what happens when you begin to center. The lump will just fling itself off but there is a remedy to
this. The first step is to clean the wheel head. I sponge away the excess clay and then I dry the metal
off with a towel and then take the lump of clay and I scrape away all the wet slip on the bottom
of it and then I slam this drier tackier area onto the metal. There is an exception to this rule and
that's when you're throwing on a slightly porous surface in this instance such as when I'm throwing
on MDF wood it helps the piece of clay stick if I dampen the surface. So to begin I tuck my arm into
my waist and I'm also resting my forearm onto the plastic wheel tray. I then position my forearm so
it lines up perfectly with the lump of clay and I want the ball of my thumb and the base of my palm
to be pushing in a straight line that intersects the middle of the lump of clay. It's not off to
the left like this nor is it too far to the right. Instead you want it so everything lines up.
So now after all of that let's really get started. Slam the clay firmly onto the metal wheel head
and push it roughly in the center and you can already see that the piece is quite centered
although there's a lot more that needs to be done before it can be thrown into a pot.
So I begin by bracing my left arm into my torso and onto the wheel tray and I lean my upper body
weight onto that arm and I lean all of that onto the lump of clay and I'll use this moment to talk
the importance of water throughout this process. The clay needs to remain lubricated the entire
time be it with slip or water and if you ever feel your hands beginning to stick to the lump of clay
or if you feel any friction it's time to add more water which I typically do just with a cupped hand
or I sometimes just keep a sponge handy which I can dip into the water in the wheel tray,
soak it up and squeeze it out onto the clay. As my left hand's palm pushes in I take the little
finger of that hand and I squeeze it around the base firmly. This creates a seal against the metal
wheel head and another barrier to ensure that it's stuck down securely. It also neatens the clay
around the base and simply stops it from spreading out onto the metal wheel head. So far I've only
been applying horizontal pressure to the piece of clay which means the lump will become ever more
conical so I need to introduce another hand which applies some vertical pressure and I do this by
using the side of my right hand to push down on the piece of clay to contain it. I push down directly
over the middle of the piece of clay matching the pressure my left arm is applying and I corral the
piece of clay into a disc shape like so and this part is really important applying both an even
pressure from the side and the top as if the pressure exerted with my left hand is too great
the lump of clay will cone up and if I push down too firmly with my right hand I'll squash the
piece of clay down into a pancake so it's an even amount of pressure from both the side and the top
which is what we're after and I sometimes take the slip from the wheel head itself like so to
lubricate the lump. Those are the hand positions I use but there are others for instance you can apply
pressure from both sides and then use your thumbs to apply downward pressure but personally I find
this a little bit uncomfortable and I feel as if I have a lot more downward control when I use the
side of my right hand in order to push down and as I center I try to squeeze the lump of clay with
all of my digits of my left hand as if I'm gripping a ball tightly and as all those fingers are
squeezing and I'm leaning in with my left arm my right hand pushes down from on top. It's worth
knowing that probably every potter out there centers a little bit differently we all follow
a similar set of rules but ultimately our hands are all different sizes and shapes and that affects
how we hold them and use them for this process so don't be surprised when you see potters doing
this process but with their hands in different positions they'll still essentially be following
the same principles just in slightly different positions. One thing that's important is to not
let the clay control your movements for instance I place my forearm down so securely that the clay
has to conform to the shape I've given it. If the clay is wobbling you don't want to let your hand
simply follow the wobbling piece of clay instead you need to position your arm and your hand so
securely that the soft wet clay has no other place to go other than the area you've designated
for it and the shape you see here is a good starting point it has a flat top and only very
slightly curved sides that meet the wheel head flush. You don't want a piece of clay which has
too much of an indentation at the bottom as now the center of gravity is slightly higher and you
might have a harder time opening it up later on. You also don't want a shape that bulges up in the
middle unnecessarily so as that means you have to push down further and perhaps unnecessarily so
when creating the hollow and forming the base of the pot. If you happen to be using a clay which
contains quite a lot of grog, one that's quite coarse, if you feel like the surface is starting
to feel like sandpaper it's best to scrape away the outermost layer and then proceed with centering
as normal. It's also worth knowing that if you are feeling this you're probably taking too much time
to center your clay. It isn't a process that's worth rushing at the beginning but you also don't
want to spend 10 minutes doing this every time you make a pot otherwise you'll never make anything
and ideally this is a process that you should be able to complete in about 10 to 40 seconds but
this does depend of course on the size of clay and larger lumps can take much longer. Another thing we
should discuss is the speed at which the wheel is spun. You don't want to do this process really
slowly because once again it'll just mean it takes longer and say when you are throwing dozens of
bowls and mugs you really want to minimize the amount of time you spend centering the clay so
in fact I never really do there's virtually no need to ever put your foot down all the way
but I do spin the wheel quickly fast enough that however I push my fingers and hands into the lump
of clay it affects the entire piece practically instantly which means you want it to be rotating
many times every second. If you spin the wheel too slowly it means you need to linger with each
movement you place on the lump of clay to ensure that it remains the same on the entire piece of
and don't go at a medium pace instead push it just that bit further. Another thing I often see
beginners do is they push this part of their hand too firmly against the metal of the wheel
to a degree that the metal can almost wear away the skin and it can become quite painful to center.
You never want to push these fingers directly down onto the metal wheel head and you'll know
if you're pushing too hard against the metal if you can see this metal residue coming off on your
hand instead you want to just glide above the metal ideally with a thin skim of slip between
the two which will naturally accumulate as you center the clay and you'll hear when you're
pushing so if you feel the friction on your hand and hear the grinding noise just lift your hand
up a millimeter or so so it's above the spinning metal. Another thing I do to ensure that the clay
is centered is I watch my fingertips instead of the clay itself if the clay is off center
my fingertips will wobble along with the clay and if I notice that I squeeze my fingertips inward
against the clay and I really focus on them not wobbling whatsoever they're firmly tense and if
they're unwavering then the clay underneath them should be quite centered so if you watch that
again and I'll purposefully knock the lump off center I lean the palm and the ball of my thumb
of my left hand into the block of clay pushing forwards and then I tense those wobbling digits
so they're completely still and then I take my right hand and bring it down on top and compress.
Sometimes in between pots you'll have this skim of dry clay left I often see people remove it
in between throwing new pots which is something you shouldn't do as as long as it's dry it'll
help the clay stick down much more firmly than it would otherwise like velcro. Once firmly attached
I can begin to center as normal but this time I'm going to introduce a new element which we
call coning this is when the lump of clay is coned up and down between the palms of my hands
this is almost like wedging the clay put on the wheel and with each cone up and each cone down
you'll feel the clay becoming more orderly beneath your hands this is because the particles which
make up the clay the platelets gradually become more aligned the analogy I use is to think of
clay like a bag of rice before it's been wedged all the grains are facing in all kinds of directions
they're completely mixed and there's no order but as the clay is coned down it causes the
platelets to collapse onto one another and align facing the same direction and in turn this makes
the lump of clay more plastic more easily throwable so I cone the clay up carefully and
then when it comes to pushing it back down I make sure I lean it over slightly as I apply downward
pressure so I tend to push the cone both forwards and down in the same motion and this causes the
clay to bulge towards the base of the lump which keeps it quite manageable and easy to work if on
the other hand you cone the piece of clay up and then just push it directly down the bulge of clay
will begin to accumulate directly in your hands which makes this process quite difficult to
control like you'll see here the point of coning is that even sometimes really thoroughly wedged
clay the lump might spin with some kind of irregularity within it but after you've coned
it up three or four times the lump of clay will begin to feel wonderfully smooth and you should
have an easier time opening up the lump and pulling up the walls of clay which will be the
topic of my next very in-depth video like this one so I lean the clay over to one side and as you
can see the bulge begins to build up towards the base so that's coning it's not necessary for every
single pot you make but it's worth learning and it's worth practicing and it can sometimes make
all the difference for instance when I'm throwing larger masses of clay or pots that are perhaps a
bit more complicated than a mug or a bowl I'll always make sure to cone the clay up and down
a number of times this next tip is perhaps a bit more subtle in nature and it has to do with how
you place your hands onto the lump of clay and how you remove them first thing you want to think
about is you only ever want to make contact with the clay when it's spinning and the same goes for
when you release your hands you never want to stop the wheel and then release your hands nor do you
want to place your hands onto a stationary lump and then begin spinning it in actuality what you
want is for the lump of clay to always be spinning when you touch it and remove your hands from it
think of it like turning wood on a lathe you'd never place the gouge onto the stationary piece
of wood and then start up the machine that rotates it and when you're turning wood on the
lathe you always want the piece to be spinning before you try to do anything to it and the same
goes for clay another thing to think about is how you release your hands from the lump of clay
ideally you want to release them very gently like so as if you release your hands too abruptly
like this you'll notice if you look carefully very slight wobble in the lump of clay and if
you do this just before you make the hole to form the base the pot could become slightly off-centered
even when you thought you centered it perfectly placing your hands onto the lump of clay isn't
so important as you can immediately center them and hold them still but when you release your
hands you want to do it very gently just to detach any connection they might have and with
enough practice it just looks like you're removing your hands normally being able to center well is
vital for learning to throw on the wheel it's the first step in the process of throwing a pot if
done improperly it makes the entire process of throwing pots more difficult and at the start
when you're learning to throw centering can feel really difficult i certainly remember what it was
like but after you've thrown a hundred a thousand and ten thousand pots it really does become second
nature more often than not the reason you might have difficulties centering a lump would be due
to the fact that the clay is too firm or far too soft for it to even be centered in the first place
my final bit of advice would be not to get too hung up on getting it perfect straight away
center the clay roughly pull up the walls roughly and try and get some finished pieces off as seeing
the process through to the end and making some pots even if they're wobbly and chunky and a bit
heavy it's those first pots that plant the seed and draw people into this craft everything after
that it's just a matter of practice and soon you'll forget that you ever even struggled with
centering. Thanks for watching and I hope you found this useful.