3 Steps To Pulling Out A Dent On A Car

Auto Retech
2 followers
Today I'm going to be sharing with you the three steps that I use to repair this damage.
Now this large dent was caused probably by somebody backing into the fender,
side swiping the vehicle slightly with maybe a bumper or their car and that's what causes
severe damage like this. So let's inspect the damage that we're going to be working with.
When we first look at this it looks like just a large dent 10 to 14 inches in overall size
but this damage is very complex and there are multiple areas that we're going to be working
with. Now when this was damaged it was hit or probably scraped from the side. It not only
pushed it in but pushed the metal up in this top area on the right hand side and this is what caused
this large crown that we're going to have to hammer down. Now just below that there also is the normal
body line through this vehicle and here we're going to have to try and restructure that damage.
And then just at the bottom here whatever scraped up against the vehicle caused this little probably
three to five inch crease and we're going to be working with that also. So the three steps used
to repair large damage like this with paint and step removal are one we use a cold glue to quickly
pull out as much damage as possible. Two is we go behind the dent inside the fender and push out
the damage from inside. And three is we actually have to work on the crown to actually push those
back down into the dent and push the panel back in to smooth out those areas. The first thing I'm
going to be starting here to pull out a lot of this damage is the process of using a cold glue.
This is just a little bit faster method than having to use hot glue on this. And this process
is used with a slide hammer and a very tacky glue and I'm just placing it right where I need to just
pull up the bulk of the damage. And you can see here it's working pretty well but it's not going
to get all the damage out. All right so I'm going to speed up the process here. After I've got most
of the damage out I'm trying to just pull out as much as I can but with this cold glue it's not
going to over pull it. It only is going to get it to the point where I need to continue to work on
it with pushing and I definitely need to work on this crown work. If you're enjoying the video so
far be sure to hit that like button and subscribe for more paint and steering repair videos.
All right now that the cold glue has done its job and pulled out a lot of the damage
here we are left with just a few more areas. We've got this lower crease down in the bottom that
we're still going to have to work with. The bulk of the damage here there's still quite a bit of
low spots and the major crown but the glue pulling was able to pull out a lot of that body line.
So if you're in Minnesota and you're looking for a paintless dent repair shop for that large dent
or even that small little door ding in your vehicle and you want professional high quality
repairs I'd be happy to take care of that for you here at Accel Dent Removal. Give me a call
for a free inspection 763-780-4000 or just jump over to my website at AccelDentRemoval.com.
I've got more contact information and location information there.
All right to start pushing out the large damage here I want to start with a large tip and I have
Dentcraft tip here and this is also a large rubber cap and the reason I like this here is it attaches
right to the tip of this tool. It also has some movement and flexibility in it so when I'm pushing
from the inside it'll push flat and not push on the edge of the tool. So I'm going to attach this
here to my Dentcraft rod. I've got an extension on here along with the tip and we'll see here
this allows me when I'm pushing on it here to just push flat and move a lot of metal and then I've got
the moose knuckle tool here. This is a great tool to apply leverage without having to push against
the tire. So with this method I'm just trying to bring up any of the low spots. It's not going to
do any finishing work but it's just going to give some structure to the panel and that's just going
to help it hold in place for later on when we do some of the crown work and in order for the crown
work to work well and actually push that metal back down into the low spots I need that tension
and that support from this part of the process. So now that I've worked on this area for a little bit
I want to switch over and work down on this lower crease. Now I'm not going to completely finish
this part of the repair until a little bit later but what I want to start with is just a soft tool
and I've got another tip here with just some testa tape on it and I'm going to use this behind there
just to lightly bring up the dent. It doesn't do any finish work but it's going to work from the
right side of the crease here just the lower part and I'm going to work over towards the left side
just lightly bringing out the deeper part of the dent and just doing it softly. If I was to use a
sharper tip tool it probably would make a lot of poke marks in here so with this process I'm just
lightly bringing this up. So we need to start working with the crowns here pushing that metal
down but also back into the low spots and the reason being is because when we pushed behind here
we weren't getting any progress and that's because this major crown here is holding a lot of the
metal. It starts from the edge and all the way up to the top so we need to work this back down and
what I've got here first is a rubber ball and it works great on my hammer here and I'm just going
to hammer this down a little bit. There's a lot of tension in this crown so it's taking quite a bit
work but I just want to gently bring it down. I don't want to hammer it too hard. Now after that
I want to switch over to this crown tool. I've got a little bit of testa tape on here just so I'm not
hitting metal on metal. This process I'm able to just bring down a lot of that crown. Like I said
it's holding a lot of tension and it's taking quite a bit of work to smooth it down and I can
do it with the hammer this way also can be more precise and lay it against the panel and hit it
with another hammer and that allows it to just have a little bit more force to bring it down
and we can even see in here how well this is working. I'll also be using my knockdown with a
rubber cap on it and this is just helping be a little bit more precise and knock down right where
I need to. So now that I've got most of the major crown work done there's still a little bit more
left to do but I now want to get in and push behind this metal. I want to structure that body
line. I want to bring up all those low spots and this process is going to take quite a bit of time
to get this smoothed out. I'm going to have to go back and forth with pushing, knocking down,
using the knockdown and the hammers and the variety of tip different tips with the pushing
from behind to get the bulk damage out with softer tips and then also switch to sharper
smaller tips to fine-tune and bring back the detail in the panel. So now you've seen the
three-step process we use to remove large damage like this with paintless dent removal. First we
use the glue pulling or the cold glue pulling method to take out the bulk of the damage. Two
we got our PDR tools behind the fender and push the damage out from the inside. This takes some
finesse work and it works to smooth out the panel and then three we use the knockdowns and hammers
and blending to push down that large crown and also push that damage back into the dent where
it goes and this also blends out that outside of the panel to make it look great.
