10 Bizarre Engines That Defied Logic

Engine Enthusiast
24 followers
When you think about American engineering from the 1900s, you probably picture solid, dependable machines. But some engineers threw conventional wisdom right out the window. These weren't just unconventional designs—they completely defied the laws of common sense. From engines that spun themselves silly to powerplants with enough cylinders to make your head spin, let's dive into ten American-made engines that made everyone ask "why?"
==============================
#machine #Equipment #Engine
When you think about American engineering from the 1900s,
you probably picture solid, dependable machines.
But some engineers threw conventional wisdom
right out the window.
From engines that spun themselves silly to power plants
with enough cylinders to make your head spin,
let's dive into 10 American-made engines
that made everyone ask, why?
10, Wright J5 Whirlwind.
The Wright J5.
Whirlwind might not look bizarre at first glance,
but this nine-cylinder radial engine
rewrote the rules for aviation reliability in 1925.
Manufactured by Wright Aeronautical Corporation
in Patterson, New Jersey,
this 787-cubic-inch power plant produced 220 horsepower
at just 1,800 RPM and weighed 510 pounds.
What made the Whirlwind defy logic
was engineer Samuel Heron's
revolutionary cylinder head design.
While other engines required rich fuel mixtures
just to stay cool, the J5 ran lean and efficient
thanks to its advanced fin configuration.
Pilots could fly farther on less fuel,
which seemed impossible at the time.
The engine featured sodium-cooled exhaust valves
and aluminum cylinder heads,
downright futuristic technology for 1925.
Charles Lindbergh bet his life on one of these engines
when he crossed the Atlantic in the spirit of St. Louis
on May 20th to 21st, 1927.
That Wright J5C serial number 7331
ran continuously for 33 1⁄2 hours without missing a beat.
Wright claimed the engine could self-lubricate its valves
for 40 hours straight,
and the overall design was rated for 9,000 hours
of operation, more than a full year of continuous running.
The J5 powered record-setting endurance flights,
transcontinental journeys, and polar expeditions
throughout the late 1920s.
Even after production ended, crop dusters in the 1940s
still preferred the whirlwind over newer designs
because of its incredible torque at low RPM.
Wright Aeronautical won the 1927 Collier Trophy
for this engine, and it's easy to see why.
Nine, Continental R670.
The Continental R670 was a seven-cylinder radial
that became one of America's
most widely used light aircraft engines.
Built by Continental Motors Corporation starting in 1931,
this 668-cubic-inch power plant produced
between 210 and 240 horsepower at 2,200 RPM,
depending on the variant.
At 465 pounds dry weight,
Continental's engineers used a bore of 5.125 inches
and a stroke of 4.625 inches,
a relatively over-square design
that helped the engine breathe better at higher RPM.
The R670 became the heart of the Boeing Stearman PT-17 Kadett
the primary trainer that taught thousands
of American pilots to fly during World War II.
If you learned to fly for the military in the 1940s,
chances are excellent you did it behind a Continental R670.
The engine also powered the Waco UPF-7, Cessna 190,
and Fairchild PT-23.
Continental produced thousands of these engines
and they proved remarkably dependable.
What really made the R670 bizarre
was Continental's decision to redesignate it
as the W670 in the mid-1930s
when they adapted it for ground applications.
The same basic engine that taught pilots to fly
ended up powering various military vehicles,
including light tanks.
The compression ratio ranged from 5.4 to 1 to 6.0
to 1 depending on fuel grade
and the engine featured a Stromberg carburetor.
Today, the Continental R670 remains a testament
to versatile American engineering
that refused to be pigeonholed into a single purpose.
Before we move on to the next one in the list,
I'd like to ask you a small favor.
If you're enjoying this content so far,
please take a second to like this video
and subscribe to the channel.
Over 98% of you watch these videos without subscribing.
Imagine what we could accomplish if everyone subscribed.
It costs you nothing, but it makes a huge difference to us.
Thanks to all of you who do.
Eight, Pratt & Whitney R4360 Wasp Major.
The Pratt & Whitney R4360 Wasp Major
was the ultimate expression of radial engine design
taken to its most illogical extreme.
This behemoth featured 28 cylinders
arranged in four rows of seven,
earning it the nickname corncob
because each row was slightly offset
in a helical pattern to facilitate cooling.
At 4,362.5 cubic inches, that's 71.5 liters,
it remains the largest displacement aviation piston engine
ever mass produced in the United States.
The first prototype ran on April 28th, 1941.
This monster produced up to 4,300 horsepower
with water injection.
The engine measured 96 inches long
and 55 inches in diameter weighing 3,700 pounds.
Each cylinder had a 5.75 inch bore and 6.0 inch stroke
and the entire contraption featured 56 spark plugs,
56 valves and a mechanical supercharger
geared at 6.374 to one ratio.
The propeller reduction gearing ran at 0.375 to one
to keep propeller tips from reaching supersonic speeds.
The engineering challenges were staggering.
Cooling four rows of air-cooled cylinders seemed impossible
but the helical arrangement
and pressure baffles made it work.
The engine required extensive startup
and shutdown procedures, mess up the sequence
and you might damage all 56 spark plugs.
Maintenance crews spent hours just changing plugs
if someone botched an engine start.
The R4360 powered the massive Convair B36 Peacemaker
which used six of these engines
supplemented by four turbo jets.
It also flew in the Boeing B-50 Superfortress
and Douglas C-124 Globemaster.
Between 1944 and 1955, Pratt & Whitney
and Ford Motor Company built 18,697
of these magnificent beasts.
The war ended before it could see combat
but it represented the absolute pinnacle
of American piston engine technology before jets took over.
Seven, Chrysler, a 57 Multibank.
Nothing screams, we'll make it work no matter what.
Quite like the Chrysler, a 57 Multibank.
When America entered World War II in 1941,
Chrysler was asked to develop a tank engine fast.
Their solution, take five Chrysler flathead
inline six engines each, displacing 250.6 cubic inches
and bolt them together around a common crankcase
in a star pattern.
The result was a 30 cylinder, 1,253 cubic inch monster
that produced 370 horsepower at 2,400 RPM.
Each of the five six cylinder banks
featured its own Carter carburetor,
distributor and exhaust system.
The central cast iron crankcase
housed a complex gear arrangement
where each bank's crankshaft drove a gear
that meshed with a central sun gear.
Two engine banks were mounted at the bottom,
angled 7.5 degrees above horizontal.
Two more above them at 27 degrees
and the fifth mounted vertically at the top.
The whole assembly weighed 5,400 pounds dry.
Chrysler's executive engineer, Harry Wilson
and engine designer, Mel Carpentier
used existing tooling from passenger car engines,
meaning spare parts were readily available.
The A57 went into production for the M3A4 Lee tank
in June, 1942, just nine months after initial discussions.
Nearly 8,000 Sherman M4A4 tanks were built with this engine.
The British who received most of these tanks
through lend-lease were initially skeptical.
The engine proved surprisingly reliable
and could continue operating
even with two of its five banks completely disabled.
In February, 1944, Chrysler advertised
that the A57 could still move a tank
with 12 of its 30 cylinders knocked out.
The multi-bank powered many Sherman Fireflies,
the most effective anti-tank version of the Sherman.
Six, Wright R-975 Whirlwind, Continental built.
The Wright R-975 Whirlwind was a nine-cylinder radial
that Continental Motors built under license
becoming one of the most important tank engines
of World War II.
Wright Aeronautical originally designed
this 975 cubic inch power plant for aircraft in the 1920s,
producing between 300 and 450 horsepower.
But in 1939, when the US Army needed an engine
for its M2 medium tanks,
they turned to Continental Motors
to manufacture the R-975 for ground use bizarre
because radial aircraft engines
weren't designed for brutal tank service.
The Continental R-975C1 and R-975C,
four variants produced 350 to 400 horsepower.
The engine featured a five inch bore
and 5.5 inch stroke with a compression ratio of 5.7 to one.
Without propeller blast or forward motion for cooling,
Continental added a large cooling fan
and shroud to the power shaft.
The engine operated under completely different conditions
covered in mud, bouncing over rough terrain,
breathing dusty air instead of clean atmosphere.
Continental built over 53,000 R-975 engines,
dwarfing Wright's production of just 7,000 for aircraft.
The engine powered the M4 Sherman, M4A1 Sherman,
M3 Lee, Canadian Ram Tank, M7 Priest self-propelled gun
and M18 Hellcat tank destroyer.
It became the backbone of allied armored forces
despite being designed for an entirely different purpose.
The R-975 was reliable, but not ideal.
It required high RPM to get tanks moving.
What made this truly bizarre
was watching aircraft engine technology
forced into tank service out of necessity.
Tank crews learned to respect their R-975s.
Knowing the same basic engine
that powered civilian aircraft in the 1930s
was now hauling 40 tons of steel
across European battlefields.
After the war, many M4A4 tanks
had their original engines replaced with Continental R-975s
because spare parts remained plentiful.
Five, Chrysler 4-2220, 11-2220.
The Chrysler 4-2220 represented
American automotive engineers diving headfirst
into aircraft engine design with spectacular results.
Chrysler Corporation received a contract in 1941
to develop a high-performance pursuit aircraft engine
for the Army Air Corps.
Their response was a liquid-cooled inverted V-16
that displaced 2,220 cubic inches
and produced 2,500 horsepower at 2,700 RPM.
The designation changed from 14-2220 to 11-2220 in 1944.
Chrysler's solution to the engine's extreme length
was genuinely innovative.
They essentially designed two back-to-back V-8 sections
separated by a gap that housed the propeller reduction gear.
Power was taken from the middle of the crankshaft
rather than the end, with an extension shaft
running below the crankshaft
to drive the propeller at the front.
This solved torsional loading problems
but made the engine incredibly long, 122 inches
compared to the 77-inch Rolls-Royce Griffin
of similar displacement.
The 4-2-2-2-0 featured hemispherical combustion chambers
with the spark plug centered between two valves per cylinder
Chrysler's first hemi design that would later revolutionize
American automotive performance.
Each cylinder had a 5.8-inch bore and 5.25-inch stroke
and the engine weighed 2,384 pounds.
A single overhead camshaft per bank operated the valves
and a general electric turbocharger
supplemented a mechanical supercharger.
The inverted V configuration positioned the crankshaft
at the top with cylinders angled downward,
allowing better pilot visibility.
The Republic XP-47H Thunderbolt served as the test bed
with the first flight occurring on July 26th, 1945.
The program terminated in November
when a propeller shaft failed,
but by then the war had ended
and jets had rendered complex piston engines obsolete.
The 4-2-2-2-0 never saw production,
but its hemispherical head design lived on
in Chrysler's legendary street and race engines.
Four, Lycoming XR-7755.
The Lycoming XR-7755 remains the largest
piston aircraft engine ever built in the United States.
Lycoming Aircraft Engines of Williamsport, Pennsylvania
began development in 1943 under engineer Clarence Wiegman.
The resulting engine featured 36 cylinders
arranged in nine banks of four,
with each bank at a 40-degree angle to the adjacent bank,
forming a four-row liquid-cooled radial configuration.
At 7,755 cubic inches, 127 liters,
the displacement was staggering.
Each cylinder had a 6.375-inch bore
and 6.75-inch stroke,
displacing 215 cubic inches per cylinder,
more than many four-cylinder car engines.
The engine was designed to produce 5,000 horsepower
at 2,600 RPM for takeoff,
with plans to eventually reach 7,000 horsepower.
Unlike most multi-row radials that used air cooling,
the XR-7755 required liquid cooling
because of its enormous size.
The engine measured 10 feet long and five feet in diameter,
weighing 6,050 pounds dry.
At full power, it consumed 580 gallons
of aviation gasoline per hour.
The engineering innovations were remarkable.
Each cylinder bank had a single overhead camshaft
with two sets of cams, one for full takeoff power
and another for economical cruise.
The pilot could shift the camshaft axially
to select between the two settings,
essentially giving the engine variable valve timing
decades before it became common.
A mechanical supercharger with a 14.4-inch impeller
ran at a six-to-one drive ratio.
The first prototype XR-77553 began testing in 1944
and successfully produced 5,000 horsepower.
When Lycoming tested it at full power
in their Williamsport facility,
local residents complained that windows rattled
and items vibrated off store shelves a half mile away.
Only two complete engines were built
before the project ended in 1946,
with jet engines changing everything.
The sole surviving engine sits at the Smithsonian.
Three, Liberty L-12.
The Liberty L-12 defied logic
not because of its configuration,
but because of how impossibly fast it went
from concept to mass production.
In May 1917, exactly one month
after the United States declared war on Germany,
the Aircraft Production Board
summoned two top engine designers to Washington,
Jesse G. Vincent of Packard Motor Car Company
and Albert J. Hall of Hall-Scott Motor Company.
Their mission was to design an aircraft engine
that would rival anything the Europeans had,
and they needed to do it immediately.
Vincent and Hall checked into the Willard Hotel
on May 29th, 1917, and emerged just five days later
with complete drawings for a 45-degree V-12 engine
displacing 1,649 cubic inches.
The design adopted the single overhead camshaft
and rocker arm valve train from Mercedes engines,
but adapted it for mass production.
The engine had a five-inch bore and seven-inch stroke,
producing 400 horsepower at 1,750 RPM.
At 845 pounds, it achieved around two pounds per horsepower.
By July 1917, Packard's Detroit plant
delivered an eight-cylinder prototype for testing.
In August, the 12-cylinder version was tested and approved.
The War Department immediately placed an order
for 22,500 engines, dividing production
among Buick, Ford, Cadillac, Lincoln, Marmon, and Packard.
More than 20,000 Liberty engines were produced
during 1918 alone.
The speed of development and scale of production
were unprecedented.
The Liberty wasn't perfect.
The 45-degree cylinder angle
caused severe torsional vibration at certain RPM ranges.
Half of the early production engines
couldn't pass the 50-hour acceptance test
due to burnt exhaust valves and accessory gear failures.
Despite these problems, the Liberty L-12
powered the vast majority of American-built DH-4 bombers
during World War I, with over 4,800 aircraft produced.
Over 16,000 Liberty engines were built during World War I,
proving that American manufacturing capability
could produce complex machinery at unprecedented scale.
Two, Adams-Farwell Rotary.
The Adams-Farwell Rotary engine
turned conventional engine design
completely inside out, literally.
Built by the Adams Company of Dubuque, Iowa
starting around 1896, this engine featured
a stationary crankshaft mounted vertically
to the vehicle's frame
while the entire cylinder block rotated around it.
Faye Oliver-Farwell designed the engine
after being inspired by a steam winch
he witnessed in the late 1890s.
The first three-cylinder version
likely powered one of America's
first rubber-tired automobiles in 1899.
The five-cylinder version that followed
produced 50 horsepower using a 5.5-inch bore
and 5.0-inch stroke.
The engine was mounted horizontally
with the crankshaft vertical,
and as the cylinders rotated,
they acted as their own flywheel.
There were no valve springs.
The valves operated by centrifugal force alone.
Each cylinder had its own exhaust pipe
mounted to the side,
and these pipes spun with the engine.
The engine design was remarkably simple and compact.
One operator could disassemble the entire engine
and remove it from the car in one hour,
and you could simply rotate it
to work on whichever cylinder needed attention.
The rotation itself provided cooling
to the cast fins on each cylinder.
The engine featured variable compression control
that allowed compression to be relieved
during starting to ease cranking.
Between 1904 and 1913,
the Adams Company built approximately 52 automobiles
powered by these engines.
The car sold for around $3,500 in the 1900s,
a rich man's vehicle.
The Model 8, a gentleman's speed roadster,
used the five-cylinder engine
and could reach 75 miles per hour.
The only surviving Adams-Farwell automobile,
a 1906 Series 6,
won the Charles A. Chain Trophy
at the 2011 Pebble Beach Concours d'Elegance
for the most advanced technology of its period.
The Adams-Farwell engine also powered early helicopters.
Only three Adams-Farwell engines
are known to survive today.
One, Packard DR-980.
The Packard DR-980 takes the top spot
because it was America's first aircraft diesel engine,
a concept that defied everything engineers
thought they knew about aviation power plants in the 1920s.
Designed by Captain Lionel Wilson,
Packard's chief aeronautical engineer,
in collaboration with Professor Herman Dorner,
this nine-cylinder four-stroke diesel radial engine
displaced 982 cubic inches
and produced 225 horsepower at 1950 RPM.
The goal was to achieve greater safety
and fuel economy by burning heavy oil furnace oil
or distillate fuel instead of volatile gasoline.
The DR-980 first flew privately on September 19th, 1928
in a Stinson Detroiter SM-1DX
at Packard's Proving Grounds in Utica, Michigan.
Each cylinder had a 4.8125-inch bore and 6.0-inch stroke,
and the engine featured direct fuel injection
at 6,000 pounds per square inch,
incredibly high pressure for 1928.
The compression ratio was 16 to one
with maximum combustion pressure
reaching 1,500 pounds per square inch.
Dry weight was 510 pounds,
giving it a power-to-weight ratio
of 2.26 pounds per horsepower.
The first cross-country diesel aircraft flight
in the United States occurred
when Wilson flew from Detroit to Langley Field, Virginia
in 1929, 700 miles in six hours and 40 minutes.
On May 28th, 1931, a Belanca CH-300 fitted with a DR-980
set a world record by staying aloft for 84 hours
and 32 minutes without refueling a record
that stood for 55 years.
The DR-980 achieved another milestone on June 3rd, 1929
when the first two-way air-to-ground
radiophone communication occurred
over Packard's Proving Grounds.
Diesel engines have no spark plugs or ignition wiring,
so electromagnetic static was greatly reduced,
allowing voice communication.
Despite these accomplishments,
the DR-980 was ultimately a commercial failure.
Diesel exhaust fumes were unpleasant,
and the engine produced considerable vibration.
Approximately 100 engines were built between 1928 and 1930.
The model DR-980 won the prestigious Collier Trophy in 1931.
Production ceased when Captain Wilson died
in an aviation accident in April, 1930.
These 10 engines proved that American engineers
have never been afraid to try the impossible.
From crankshafts that stayed put while everything else spun
to power plants with enough cylinders to need an accountant,
our predecessors built machines
that made people scratch their heads
and ask how they ever worked.
The beautiful thing is they did work often brilliantly.
That's the American way.
See a problem, ignore conventional wisdom,
and build something so bizarre it just might succeed.
If you enjoyed this journey through mechanical mayhem,
hit that subscribe button.
Trust me, there's plenty more where this came from.
Until next time, keep that wrench handy.
