Resetting a Diamond Ring in 4 Steps

Handmade Jewelry
2 followers
2 Video Views·Nov 30, 2025
In this video, I'm resetting a diamond ring in 4 steps.
This ring is made of half-sanded diamonds.
If you look closely, some facets are sanded, others are not.
This is actually very interesting, because this way you can see the raw form of the diamond
and compare it with the less shiny, sanded facets.
This ring is currently US size 5.
The owner of this ring wants to change it to size 7.75.
I could have cut somewhere on the ring and soldered a small piece of wire to increase the size,
but I don't want to have too many soldering points on this smooth ring, because it could be weakened.
So I decided to take out the diamond and make a brand new ring for it.
In this way, the ring consists of a massive wire and there is only one connection.
First I have to take out the diamond, to remove a diamond in a basel version from its version.
I cut the vessel wall from the side.
I have to make a cut around the vessel, so that I can lift the wall and take out the diamond.
That's why I consider casting vessels to be one of the safest casting methods,
because in order to get the diamond out, you have to completely destroy the material around it.
In order to lift the material around the diamond,
my saw blade has to cut through the metal and reach the diamond behind it.
When the teeth of my saw blade reach the diamond, I know that they have cut through.
My saw blade made in Switzerland is made of high-quality steel.
But every time I'm done cutting a vessel wall like this one,
I have to exchange the saw blade for a brand new one.
Because as soon as the teeth reach the diamond, they are sanded off by the hardest natural substance in the world.
While the cut almost goes through the wall, I push the vessel up.
The fact that my nails are pretty hard helps me a lot.
This way I can concentrate better.
I see that the diamond is moving.
Maybe I should have cut a little further.
Doesn't matter, I got it out.
From this angle I can see some shiny polished facets and some that are unpolished.
About half of the surface is actually polished and the other half is in a rough state.
This is the wire that I just cut through.
My wire is made of 100% recycled material.
After making the bar, I first roll it out on my rolling pin and then bring it to the required size with a puller.
After cutting to the desired length, I start bending.
There are actually many ways to bend my wire into a ring.
What I'm doing here is just one of them.
I first bend it with a semicircular pliers.
Later I use the workbench to bend it so that both ends of the wire meet.
Finally, I make a few small adjustments so that they meet nicely in front of the soldering iron to connect them permanently.
I use hot glue to fill the gap.
My soldering station is located in front of a window facing south and it is a sunny afternoon when I do this.
It is too bright, so I put a small melting iron next to the ring to shield the sun's radiation a little.
So I can see better.
This is what the wire looks like right after soldering.
To make it perfectly round, I stretch it with a ring stretcher.
After the first stretching, I brought my ring to size 5.5.
Whenever I feel that the ring is no longer stretching, it must be analyzed to remove its inner tensions and facilitate the processing.
When the ring is ready, I make a shaft that surrounds the diamond.
Before I solder a base, I plan the section of the shaft with a flat file.
This small circle has a diameter of about 5 mm.
The fact that I have small hands gives me an advantage when holding small objects like this one.
When filing, the metal always sticks to the file first and it is easier to process when the edge has become smoother.
To check whether the underside of this shaft is flat, I can put it on a flat surface like this one.
If there is no light shining through between the shaft and the surface, I know that it is ready to be soldered.
Before I attach the shaft, I have previously melted some EC solder on the surface.
You see, as soon as the solder melts again, the wall sinks to the lower piece.
This is what it looks like after the flux residues and burrs have been removed.
Next, I cut off the excess material with my 22-year-old jewelry saw from the edge.
If you have seen my previous video, you know that I have been using this saw frame since the first day in 2003.
This is definitely one of the best tools for jewelry making that I have ever bought.
When removing the excess material with the saw, I try to cut as close as possible to the wall, but I do not aim for a flush cut.
When most of the material is removed at the edge, I use a flat file to make the floor flush with the wall of the vessel.
The metal edge is actually pretty sharp.
But I think, after all these years, the skin on my fingertips has gotten pretty thick.
The cut next to the nail on my middle finger is not from the jewelry production.
It was caused by a screwdriver, as you saw when you saw my last photo.
This is what the vessel shell looks like at the end.
This is a borax comb.
I put water in the shell and then grind it to get a thin liquid paste.
With the ring held with the crosslock tweezers, I solder it with a light solder to the back of the vessel.
Basically, I only use two types of solder, light and hard.
In fact, I don't have a medium-heavy solder in my studio.
This is what the ring looks like after it has been cleaned.
It is ready to pick up the diamond that I released earlier.
The vessel tool that I use here, I made myself in 2003, when I started making jewelry.
I show in my other videos, how to make such a vessel tool, together with other types of vessel tools.
If you are interested, you are welcome to take a look at it.
I have listed the links in the description below.
This is what the ring looks like after it has been polished.
In my previous videos on my channel, I have shown how I polish such rings, so I will not repeat it here again.
This ring is 7.75 inches in size, just as its owner wanted.
This is what the finished ring looks like next to the vessel.
It originally came from a completely destroyed brass bowl compared to a functioning one.
I hope you find this video helpful and I'll see you next time.
