How to Build a Small Patio Pond (300L) with DIY Filter | Perfect for Goldfish!

Nature Fish Tank
87 followers
18 Video Views·Nov 14, 2025
In today's video I'm going to be attempting to spruce up this part of my garden in between my
kitchen door and patio door. I'm going to be using a number of bits from the garden. I've got some
off cuts from a pond I built earlier on in the year. These are sleepers, off cuts of sleepers.
This is a 200 litre water container I've had for many years sitting in the garage.
This is a half whisky barrel plastic. It takes about 100 litres which I'm going to use as a
filter. I've got a few plants lying around the place so what I'm going to do is with these
materials I'm going to see what I can put together and try and make a water feature to make it look
a bit better. So the off cut sleepers are going to be arranged in such a way that they support
both the 280 litre container and the 100 litre half whisky barrel container with a bit of gap
in either side. The idea of using the sleepers is they look quite nice on the floor and not only
that they do give a little bit of insulation against the cold floor. Once the containers
were in place I got the long level out and checked everything to make sure it was all good.
Then came the plants I had available to me so I spent a bit of time messing around with these
and putting them in various positions to try and make the pond look a bit more natural and
bring a bit of greenery to it. Once I was happy with the positions of the plants it was time to
get some water into these containers. Now the water was going to be coming from the existing
fancy goldfish pond I built earlier on in the year and as I'm going to be moving some of those fancy
goldfish over you know the idea is to use the water from this existing pond. I'm also going
to be transferring some of the filter media so it helps against you know new pond syndrome.
I've done this a number of times in the past and it really does help when starting up a new tank.
Obviously you need an existing pond to begin with but as minimal shock to the fish because
you're essentially transferring the same water and filter material just over to a separate container.
I'm going to be using a 900 litre an hour pump and a 400 watt heater because I mean
this is a 280 litre container. The whisky barrel is 100 litres. You're probably looking at 350 litres
of water in total once the filter material is in there. Having it containing fancy goldfish and
being outside it is going to have to be heated. I'm hoping the 400 watt heater is enough if not
I may up it. It depends I'll keep an eye on it as we go along. So here I am placing the 900 litre
an hour pump in the opposite corner to where the overflow is on the filter. The pump actually has
suckers on the bottom because it's quite a small pump so I'm going to push that to the bottom of
the container then hide the hose around the back and then that hose is then going to go into the
filter. With that in position I'm now going to put some sand into the bottom of the container.
In the past I've tended to use pea-sized gravel but this time around I think I'm going to go with
the sand and when you're looking at the fish from above I think the goldfish stand out a little
better due to the colour of the sand compared to all the multitude of colours with pea-sized gravel.
Simply poured it into the container and tried to get an even spread. I did end up taking the pump
and the heater out to get the sand out of it and replacing them. While letting that settle I was
going to move on to the filter. I have the 100 litre half whiskey barrel. I've got an overflow
and a flush valve. I've got two bags of alpha grog and some Scottish pebbles. This is a hell of a lot
of filtration for a pond this size. I mean the filter is roughly a third the volume of the
actual container. It does mean we can have a few more fish in there though so I'm going to get started
on drilling the hole for the bottom flush valve. You just need to match the hole saw to the size
of the bottom valve you're installing. When drilling the hole place something underneath
the container or you know hoover up afterwards because the plastic can be a danger to wildlife.
Once the hole's drilled try and smooth off the edges as best you can. Insert the valve and screw
it on. Once you've assembled the whole valve line it up and then use a pair of grips and tighten it
up properly. Flush valve is essential because by flushing it once a week you know and then doing a
water change to replace the water you flushed out. You know you're keeping your pond and your
filter very healthy and clean. I would happily use this size filter on any pond up to about 1,500 litres
stocked with goldfish. The only thing you might have to change is the size of the pump and the overflow
to correspond with that size pump. On this container there's a bit of an overhang of plastic
so I'm just cutting out a little section here so I can get the overflow on correctly. You can use
any type of plastic container to build this filter it's just whatever you fancy really and whatever
fits in with your setup. Again when drilling just size the hole saw slightly bigger than the
tank connector you're using. Once the hole's drilled smooth the edges and tighten up the nut
and give it a few turns with the grips. Once the flush valve
and the overflow have been installed it's time to move the container back next to the pond
line it up fill it up with water and test it. You need to make sure everything's running smoothly
and there's no leaks first before you put any stones or alpha grogging or whatever you're
putting in because it's a pain you know if you find issues you've got to get it all out again.
As the water was rising here I noticed a few bits of floating plastic so I fished them out because
obviously I don't want the fish eating them. The size of the outflow here is a little bit on the
smaller side for 900 litres an hour so I'm probably I've got a flow reducer so I will
reduce that slightly to probably about 700 litres an hour it should be fine. I cut slits in the pond
hose position it around the outside of the container and have the end of it in the middle
and position the cobbles not crushing the hose and then covering the clean valve as well. This
gives an even spread of water if you when you position the hose around the outside and position
the rocks carefully when the added weight of the outflow goes in the top it won't crush
the flexible hose. I'm going to evenly distribute some of this filter material I've taken out of
the fancy goldfish pond existing filter. I'm not even sure what this stuff is called I mean it's
an existing filter it's the very first filter actually I bought years ago but I mean I've
just kept it and gradually put it in other DIY filters that I've built. As it already contains
beneficial bacteria on the surface area you know it gives it a new filter boost. I did make holes
in the bottom of these alpha glog bags open the top and you know pour quite a few litres of pond
water through them to try and get most of the dirt out but I don't think you're ever really going to
get all of it out. So that's the two bags of alpha glog in an evenly spread and I have got this
plant here that I'm just going to sit there on the top it's a bit late in the year now you know
we're in the September but as soon as the springtime comes around you know that will kick back into
life. The pump's been turned back on and this is slowly filling up now as you can see with the
dirt from the alpha glog and the sand as well I mean this is this is looking pretty filthy at
the minute but given time this will all filter out. Once it clears up I'll flush that bottom drain
and then top the water back up again and it'll be ready to go and clean. This is how it was looking
the following day it's cleared up a little bit I did put some plants in there from the fancy
goldfish pond they help a little bit with the filtering as well. I've adjusted the flow rate
slightly as well but that water level on the filter is still sitting quite high so I think
there's a possibility I may have to increase the size of the outflow. It's been 48 hours now and
as you can see that's really cleared that water up that's approaching crystal clear now I would
say so the filter's done its job there. The next thing I'm going to do is clad the pond with this
wood I'm going to cut it down and stick it around the sides with some CT1. I'm hoping it makes it
look a little bit better. I was simply putting two blobs of the CT1 on there and then lining it up
and sticking it onto the side of the container. I simply stuck six at a time stood back
had a little look and made sure they were all lined up straight and moved on to the next section.
After around four or five days I opened up the cleaning valve got some of the water out then
replaced it and tested the water and it was all looking good so I introduced a couple of goldfish
to keep the beneficial bacteria ticking over obviously they need the ammonia to stay alive.
With the wood added to the side of the container that was pretty much it now
over the next two weeks I slowly added a few more fish and here we are it's nearing the end of
October and it's looking quite nice I mean we have a bit of space on the sleepers there at the
front so as soon as spring comes around I'll get it planted a little bit better and I think it
will look really nice. I'll leave you with some short videos of the fish and some close-ups
they're enjoying their new home and I hope you've enjoyed the video.
