Rebuilding my Crashed Ferrari 812 Superfast - Part 6

Automobile Identity
371 followers
#automobile #autos #cars #4wheels #luxurycar #sportcar #highspeedcar #testdrive #toyota #tesla #porsche #hyundai #rollsroyce #royall #suvs
Well finally, finally, finally,
upstairs here in the spare bedroom,
we have the full carbon fiber body kit
from Mr. Duke Dynamics.
This, of course, is for the crashed Ferrari 812 Superfast.
And in today's video,
we're actually test fitting this on the car.
You can see the full carbon fiber hood,
full carbon fiber rear bumper, front fenders,
all the other nonsense.
Ladies and gentlemen, welcome back to the channel
and welcome back to the vlog.
Well this is a long time in the making.
Finally, I've had this body kit for what?
Six months, seven months?
Now this is the Duke Dynamics 812 Comp Wide Body Kit.
It might be the first kit of its kind in the world,
I'm not entirely sure,
but this thing is gonna be extra wide.
Well I just counted and we got 23 pieces in total.
This kit is gonna be so crazy when it's on the car.
So the front fenders are for replacement fenders,
whereas the rear fenders are actually molded onto the car.
Now as far as where we're gonna begin,
I think the driver's side makes the most sense.
The damaged side is on the passenger side,
and the passenger side is perfect,
but just for prosperity's sake,
I think we're gonna start with the front driver fender.
Now weirdly enough, this piece is not raw carbon fiber.
Every single other piece on the kit is,
except for the driver front fender
and the passenger front fender.
Why that is, I have, well, I don't have any idea.
Now it really shouldn't matter
because I am planning on painting the entire car.
What color I'm gonna paint it,
I haven't figured out quite yet,
but we gotta go with something subtle.
I always do subtle, right?
This side skirt should kind of sort of just clip in like so.
Obviously I can't do this while holding the camera.
Oh, the door should just kind of sort of, look at that.
What?
Well, it looks like overall,
the fitment on the side skirt is pretty good.
Now I put a bolt here and a bolt here.
I'm not gonna fasten down the entire thing
just because I wanna fit all the other pieces,
and sometimes you gotta make minor adjustments.
With the skirt on, just that alone looks sick.
Now, before we do anything too crazy,
I wanna protect this door
because the last thing we wanna do is cause more damage.
Now, you'll notice that this wide body kit
is actually significantly wider
than a factory A12 Superfast,
so we're gonna have to get new wheels eventually,
which also means we gotta measure new wheels
basically today or tomorrow.
Honestly, the fitment right now, I am thoroughly impressed.
This is going too well.
Well, I'm gonna pull the A12 back into the garage,
lift it on the BendPak Lift
to finish up the front end of the car,
but I felt like this was too cool of an opportunity.
That is so crazy with the front fender on the car.
It is coming to life.
You can see we probably have, what,
an extra maybe two inches, give or take?
Well, the passenger fender didn't go on
nearly as easy as the driver fender,
which kinda makes sense.
When the car was in the accident,
it hit it on the passenger side,
and so there's a couple little things
that are sort of messed up,
mainly the passenger door.
You can see this section that is dented in.
You can see the gapping right there.
I gotta get this door repaired.
I'm really hoping I can repair it
then I don't have to replace it
because Ferrari parts are very, very, very, very expensive,
and so far, I mean, this thing's not fitted
to perfection quite yet
because we're just test fitting all the rest of the kit,
but overall, she looking primed.
So it looks like we have one, two, three, four,
five, six, seven, eight, nine pieces
just for the front bumper.
At least that's what I think.
Don't judge me if I am wrong.
There's no instructions whatsoever.
I think we're gonna start with this front piece right here,
but before we get to that,
today's video's been sponsored by Vessi.
If you've been watching my channel for a while,
you know that I love Vessis.
I've been wearing my Vessis for, I think,
maybe five years now.
Now, Vessi has shoe options for everybody.
You got your women's sneakers,
you got your men's sneakers,
your high tops, your low tops,
and there are so many more options
on Vessi.com slash Stradman,
but what I love about these Vessi weekend sneakers,
they are so versatile.
I can wear these every single day,
no matter the occasion, no matter the weather forecast.
I can wear these to work.
I can wear them to church on Sunday.
I can wear them when I'm walking Oscar
or when I'm working on a crashed Ferrari 812.
And the thing I love about the Vessi sneakers,
more so than any other thing,
they are waterproof.
Over the course of the last five years,
how many cars have I washed wearing my Vessi sneakers
and my feet have stayed dry and warm?
With Vessi's waterproof technology,
it means you no longer have to plan around the forecast.
You can easily slip them on and off
and they're comfortable every single day.
And the durability,
these Vessis will last you years and years and years to come.
Your feet will thank you.
Now I love my Vessis and I know you guys will as well.
Vessis are waterproof, they're comfortable,
they're stylish, they're ready for real life adventure.
Pick up a pair at Vessi.com slash Stradman
and you're gonna instantly get 15% off your first purchase.
Check out the link below
or simply visit Vessi.com slash Stradman.
This bumper is out of control.
It looks so crazy cool.
It's so crazy.
What a process it was to get to this point.
We had to pull the motor, we had to repair the frame,
we had to put the motor back in,
drive around the neighborhood, et cetera, et cetera, et cetera
and now in half an afternoon, the car is like coming to life.
Now yes, yes, yes, I realize the bumper's held on
by three bolts that are not even tightly fastened down
but my oh my, that view in the rear view mirror,
yes sir, the Duke Dynamics Widebody 812 Superfast.
Now this piece somehow, maybe kinda sorta like,
we're just gonna put it there for now.
Whoa, whoa, whoa, whoa.
It's so crazy when you have a vision
and then you see that vision start to come to life,
drop her to the ground, let the suspension settle.
Yeah, that's right baby, that's right.
This thing is just coming to life.
We gotta go get the hood as well.
Wow, this car is gonna be transformed.
Well the last piece for the front end
and certainly not the smallest piece,
we got the full carbon hood.
Now how I'm gonna get this on the car,
I haven't quite sorted out but you guys watch, be amazed.
Selfie is here to save the day.
Oh and Floof, I hear Oscar.
Oscar, come on, carbon.
Okay, you guys gotta see this.
The final piece of the puzzle.
Oh my goodness.
The fitment looks like garbage, okay,
and I understand that but, but.
The classic hope and pray is clips are always,
that's not a bad start.
I can't figure out how to get this rear bumper off
so we're pulling the taillight.
Upon further review, we're gonna pull out
the other taillight.
And that is one rear bumper basically removed.
This has gotta be one of the more special things
that I've seen in my time working on cars.
This makes no sense whatsoever.
So I got the rear bumper right here,
I've disconnected it off the car.
Now I gotta unclip all the different wiring harnesses.
Well this main harness here, you'd think,
there'd be a connection point here,
maybe a connection point there.
There's not.
The only way to actually get this bumper out of here,
I have to disconnect every single point
on this wiring harness.
I already did the driver's side,
now I gotta do the whole passenger side.
All the parking sensors, the license plate lights,
et cetera, et cetera, they all gotta be disconnected
so that I can get this wiring harness off this bumper.
We gotta disconnect every single one of these.
It's not like it's that hard, it's just why?
What would be 10 minutes worth of work
is now gonna turn into 20, 30 minutes of work.
Assuming I can get this off, come on, nope.
Today, there we go.
This entire passenger side has been pretty much removed.
We got a couple more connections in here.
Now you're probably gonna say in the comments like,
oh, well the connection point must be up here.
You can see the grommet through there
and if you feed that through,
you can actually see there's heat shielding right there
that would also have to be removed.
That seems like more work.
If you're a Ferrari technician and I'm doing something wrong,
please let me know in the comments below
because this doesn't make any sense whatsoever.
We just got a couple more connections.
I gotta remove these nuts here as well.
And many, many, many clips later,
we got just this one last connection.
Should be able to squeeze, bada boom, bada bing.
This entire wiring harness has been fully disconnected.
Yeah?
Yeah, okay, we good.
This has gotta be one of the more ridiculous rear bumpers
that I have ever removed,
but ladies and gentlemen, it is 100% fully removed.
It's so crazy to see the difference
between these two bumpers.
Obviously, we got the raw carbon Duke Dynamics.
This thing weighs maybe like, I don't know,
two pounds, three pounds, give or take.
Whereas obviously the OEM one weighs a lot more,
but it also has all the other nonsense attached to it.
It's got the backup camera,
it's got the license plate lights,
it's got the Catalino,
you got the exhaust tips right there.
That is a cool bumper.
So I gotta transfer everything from this rear bumper
to this rear bumper.
Now removing the taillights on the driver's side
was not a big deal because we now gotta remove them
on the passenger side.
And taillight four of four clip off like so.
I don't know the full order of operations,
but this piece goes in
and then this piece kinda sits like yay.
Now like the front bumper with the rear bumper,
I'm not gonna add everything on quite yet.
I just wanna see if it'll clip in place
and then we can go from there.
The silly wiring harness, once again,
is gonna be the death of me.
I gotta figure out a place to kind of,
we're gonna drop it out the bottom for now.
Now sometimes it's really easy to get ahead of yourself.
It's fun to put the bumpers on.
I gotta protect the paint though.
This is take number two.
Out.
Okay, oh, yes.
Kind of like, should clip in right there.
Now I'm struggling with the rear bumper ever so slightly.
You can see this side is not clipped in,
whereas this side is clipped in.
If I was to clip in that side,
this side would become unclipped
and that's because there's a rear crash bar
that is protruding ever so slightly.
We gotta trim the smallest little angle off that crash bar
so we can clip in both sides.
So the rear crash bar right here,
I gotta trim just the tiniest little corner there
and the tiniest little corner there.
We got our safety glasses and we have the angle grinder.
Well, easy enough, cut number one and cut number two.
Now I would paint those black right now,
but first I wanna fit on the rear bumper,
make sure it fits, and then after I confirm
that it does fit, we'll pull the rear bumper
and then paint and paint.
Now it seems like the cut worked on this side
and on this side this should clip, yes sir.
Now next up we have this piece,
which is our exhaust surround
and it kinda goes in like so.
A bunch of the holes have already been pre-drilled,
you can see the three right there,
so we gotta install some M5 rivnuts.
And easy enough, M5 rivnut right there and right there.
I honestly could not even imagine doing body kits
without rivnuts.
It is a beautiful, beautiful technology.
Now the last piece is the center section of the diffuser.
It almost looks like a rain light goes there.
So this piece kinda sets in, it looks like,
like that, maybe?
I think that completes the entire rear bumper assembly.
It's a little bit difficult to show.
So we have the center section of the diffuser
as well as both exhaust surrounds.
Working on the back half of this car
is a little bit awkward
because it's a little bit tighter on space.
Now the last couple pieces are gonna go
and the last couple pieces, as I mentioned,
gotta be panel bonded onto the car,
but it also does clip in here on that rear three quarter.
That's pretty much it right there, look at that.
That's it.
It's so funny because the A12 looks so cool,
but at the same time, it looks like a piece of junk.
You got blue painter's tape everywhere,
you got microfibers just so the carbon fiber
doesn't scratch, and then you got fender gap nation,
but my oh my, this car, when it is done,
it is gonna be so wide, it is gonna be so aggressive.
The A12 from Duke Dynamics.
The view of this car from every single angle
is just ridiculous.
I also realize I'm missing the center section,
which I actually put right in here.
Now this piece also has to be panel bonded onto the car,
so there's really no way to mount it in place right now,
but it kinda sorta clips, kinda like that.
Oh my goodness, girth nation.
Welcome back to the channel, welcome back to the vlog.
And I just realized we're missing one last piece.
So this apron piece kinda sits right there,
and this piece will stay exposed carbon fiber,
everything else will be painted,
but this will stay carbon fiber.
Oh yes, yup.
This project is so overwhelming
because there is still so many items to do,
and the order of operations has gotta be precise.
I have to order wheels ASAP,
because custom wheels usually take three months,
give or take,
and you can see how significantly wider this rear is
than a factory A12 Superfast.
So we gotta measure ASAP,
but I gotta get these rear fenders
panel bonded onto the car,
and then I gotta get it molded on
so you can't see the line whatsoever.
Now I've never done that before,
and would I like to try that?
Absolutely, and on a lot of cars I would,
but on this car, I feel like I need a professional
to actually mold the fenders on.
And of course it goes without saying,
the interior, yes, yes, yes,
I hear you guys loud and clear.
The dashboard, like I said,
seven to 10 business days,
I said that yesterday,
so six to nine business days,
we're gonna have the dashboard,
and we can complete the entire interior.
Now I wanna paint this car,
I wanna do another custom interior,
and I'm trying to figure out exactly what spec to do.
It's gotta be subtle, like I said earlier,
it's gotta be subtle.
I always do subtle specs,
so I gotta figure that as well,
and then I gotta fit all this front end,
I gotta get all these gaps absolutely perfect,
because right now, obviously you can see,
I mean that's not acceptable,
that's not acceptable,
and this is definitely not acceptable.
Now crazy enough, the original spec of this car
did not have Ferrari shields right here,
so I gotta order two,
one for the driver,
one for the passenger side.
This front end, I gotta get like a custom grill made,
I gotta install all the parking sensors as well,
I gotta get an emblem right here,
which I should be able to pull off the old bumper,
so there's a lot of tiny little details.
I gotta fix the passenger mirror,
I gotta fix the passenger window,
I gotta fix the door,
I forgot about the door.
Well there you guys have it,
the first test fitment
of the Duke Dynamics Widebody 812 Comp.
This car, when it is finished,
is gonna be one of the coolest cars I have ever done.
Now it's a long process to get to the finish line,
but this was a huge step in the process.
This car, that view, yes sir.
We have a lot of fun videos in the pipeline.
We got massive updates on the basement,
on the back cave garage,
contractors were here all last week,
they were here today,
they're gonna be here tomorrow.
That video's coming very, very, very soon,
and then we have another fun video coming
that's a little bit nostalgic.
More on that later, but on that bombshell,
today's video is over.
