BMW (جنزير الصدر)BMW Petrol Timing Chain سلسلة التوقيت #KasemAutoservice #bmw #timing #chain

KasemAutoservice
15 followers
سلسلة توقيت البنزين من BMW (جنزير الصدر)
BMW Petrol Timing Chain
NB ; In a video we explain in detail the timing chain
ملحوظة ؛ في مقطع فيديو نشرح بالتفصيل سلسلة التوقيت
#KasemAutoservice #bmw #timing #chain
Peace be upon you. How are you guys?
We have a 4-cylinder petrol engine.
We are going to install the brake calipers.
Of course, these are the calipers that passed through the brake calipers.
This is where the vanos and the calipers are located.
All the new parts are present.
I will install them step by step.
The installation method.
I don't have a mechanic here.
Follow us.
Let's see how to install the brake calipers.
This is the air compressor.
First, we have to remove the crank.
Like this piece.
We have to remove the crank.
This is the bracket.
It is installed like this.
This is the second bracket that has to be removed.
Turn it a little bit, Abou Tayeb.
A little bit.
No, a little more.
That's it.
Now, the crank is closed.
That's it.
Now, we are done with the crank.
The second step is to remove the centric meter.
We have to remove the centric meter.
After we closed the crank, we will remove the centric meter.
Of course, this is installed here.
That's it.
Hold it a little bit, Abou Tayeb.
Hold it like this.
A little bit.
So that we can see both.
A little bit.
This is installed here.
Ok.
No, sorry.
On the contrary.
I will install it here.
A little bit.
Ok.
A little bit.
Now, we closed the centric meter.
Now, we tighten the screws.
We tighten the two screws.
Here, we closed the crank.
A little bit.
Here, we closed the crank.
We closed the centric meter.
Now, we will install the chain and remove the vanos.
This piece removes the vanos.
Now, I will explain to you how to do it.
I will remove this piece.
Ok.
I will remove this piece.
Ok.
Now, we closed the centric meter.
Now, it is 100%.
We closed the crank.
We will go to the other side.
We will install the chain and remove the vanos.
Now, we will install the chain.
I will show you.
Look at the screws.
I will install the screws.
Now, we will remove the vanos.
We will remove the vanos and remove the screws.
Now, we have removed the screws.
Here, we will install the chain.
I will install the chain.
I will go to this side.
Ok.
I will install the screw.
Here, I have another screw.
Now, I will install the chain.
After, I will install the nut.
I will lock it.
I will close the crank.
I will install the nut.
I will install the rim.
I want to install it here.
I will install the center and remove the Vanos.
I'll show you how to do it.
Now, after installing the cow,
I'll install this new bull.
This is the new bull.
Now, I'll install
this bull here.
I'll remove these two
and then I'll install the bull.
Do you understand?
Of course, it's important to note
that we installed a bull here
and a bull here.
This bull must be tightened
by the watch.
Now, I'll tighten it by the watch
to make it work properly.
This bull is very important.
Even the agency recommends
that this bull must be tightened by the watch.
But the rest is normal.
Of course, this one and this one
must be tightened by the watch.
As you can see,
this bull must be tightened by the watch.
I'll install two bulls here.
Now, I'll tighten them by the watch.
I'll install two bulls by the watch.
I'll install them by the watch.
I'll install them.
I'll tighten the second bull.
Now, I'll check
if there are any problems.
I'll check if the bull is fine.
I'll install this bull here.
Of course, this bull
must be installed
by the watch.
Now, I'll tighten the second bull.
Now, I'll tighten these two bulls.
I'll tighten these two bulls
by the watch.
But there is one problem.
The agency recommends
to tighten the bulls by the watch.
I know how much I have to tighten them.
But I'll send you a paper
so that you know how to do it.
It's written in all languages.
In German.
Here, in Arabic.
It's written
on the paper
that the angle of the bull
must be 20 degrees.
The angle of rotation must be
180 degrees.
Now, I'll tighten them
as it's written here.
But before I tighten them,
I must install the bull.
This is the bull.
I must install the bull
before I tighten them.
If I didn't install the bull
and tightened them,
all the measurements would be wrong.
This is the bull.
I must install the bull
before I tighten them.
If I didn't install the bull
and tightened them,
all the measurements would be wrong.
I must install the bull
before I tighten them.
After I install the bull,
I must check the balance.
Of course, I must give you
I give you these notes
because all these things
happened to people
and I regret them a lot.
This is the bull's angle
but it must be in Aluminum state.
See the bull has Aluminum in stern.
I must install the bull
before I tighten them
because Aluminum keeps rotating.
Aluminum keeps rotating
except it's meet.
It's in chesshhhh
If I didn't tighten them,
all the measurements would be wrong.
That's why
I must install the bull
during the hour.
Aluminum is not like milk, milk keeps on tightening and it closes, this one doesn't close, it keeps on tightening because aluminum keeps on eating and it gets fat.
Now we put 90, now we put 90 and we tighten, everything is in order.
This is the second step, then we put the hand on the lever and we continue at 180 degrees.
Now we tighten the last one.
Now we are done with everything, we are going to put all the braces.
We turn it around 2 or 3 times, then we put all the braces, everything has to be in order.
Let's put the braces.
Now we have to turn it around 2 or 3 times, then we put all the braces, everything has to be in order.
We have to put the hand on the lever.
Now we put the hand on the lever, everything has to be in order.
Now we are done with the engine, we are going to put all the parts together, put it in the car and start it.
I will show you how it works.
