In this AMAZING RESTORATION video I exceeded all my expectations on how good this would look when it was finished. This is my favourite restoration so far and I love it.
NOTE: Please be advised that the links provided are affiliate links and I may get a small commission from qualified purchases. This is at absolutely at no extra cost to you! Always be sure to read all manufacturers instructions and use appropriate safety equipment when using any of these products, and do so at your own risk.
Hi everyone and welcome back. In this video we are going to be taking this 1930s
writing bureau by a company called Gentique which is a guy called Geoffrey Jenkins
and apparently this guy used to be quite a world-famous toy maker before he started
designing and manufacturing furniture and he's quite famous for a failed invention of a water
powered hydraulic toothbrush just what everybody needs. Yeah apparently that didn't do too well it
was super expensive to buy and super expensive to make so he focused on his furniture. You will see
a lot of Gentique furniture this like I say this is from the 1930s and it's a writing bureau but
he's probably more famous in the 50s and 60s for his mid-century modern sideboards.
So this is a piece of furniture for a customer this was her mother's furniture and it was loved
by her at one point but unfortunately it spent probably the last decade in my customer's garage
being used as a tool chest so she really wanted to get this restored and I said I would be able to
help. So stay tuned and you will be absolutely amazed by the result at the end of this video.
The finish on this was totally failing as you can see here I think it's shellac but I've never
actually been able to remove a top coat before with my shop vac so unfortunately this didn't
work for all of the piece just on the sides for some reason. You can just about make out
the manufacturer's mark stamped in the back here so I'm just trying to darken it up so you can see.
As always I like to start each job by giving the piece a thorough clean. I guess it's not
really needed in this case because I am going to strip the finish but
it's just it's just part of my process and I like to start with a clean piece.
So the first job is to remove the handles from the drawers and straightforward just screws at
the back so remove them and just remove the handle ready to restore later. I've done quite a few of
writing bureaus now and it's so much easier to just take it to bits really so I always remove
the drop down desk front so I can get to the hinges and then there are the pigeon holes inside
which you need to get at by removing the back of the unit which you'll see in a second.
You could see me there just trying to see how the pigeon holes inside were actually fixed
to the unit so to get a better look I'm going to take the back off.
As you could see there there were some screws that are removed but unfortunately it's also
nailed in which which is a pain really. I'm just banging it from the other side just to try and
push the nails out a bit just so I can get the pliers on them. Unfortunately not all the nails
did that and this took quite a while to get off but I got there in the end and
you know didn't create too much damage. The pigeon holes were just simply nailed
into the side of the unit so they were fairly easy to take out once I got the back off.
As you can see there I started to remove the existing finish with the scraper and my sander
but I soon dropped that idea because I had to do these details anyway with the paint stripper just
because you know it's just almost impossible to get with a sander. Paint stripper in, a little
a little soft wire brush just to get into the details and remove that. This actually worked
really well this stripper so that informed my decision going forward. I put the scraper to one
side and I then decided to strip the entire piece which took me a long time, was very messy
but probably would have took a lot longer with the scraper and the sander.
Hopefully from that you can see why I chose to go down the route of using stripper. It is a messy
job and you know it doesn't take five minutes it takes a long time because you have to put it on,
wait for it, neutralize it, put it back on again if you if you've not pulled up any of the top coat
and then neutralize again so it's not quick but it's probably less time consuming than just
sanding the finish off. The top coat on this was was so thick and so dark it actually hid the
the beautiful wood grain in this in this old piece of furniture and I think it would be
refinished over and over again over the years so it definitely needed stripping back down to the
this has been used as a tool chest so the drawers were in a bit of a sorry state
they definitely needed attention and they got completely sanded and refinished.
Despite the state this was in there was only really one drawer that had the veneer damaged on it
I wanted to try and patch that so I had some I had some veneer some edge band walnut veneer
and I was just trying to see if that was a good match. I also had some oak veneer
and I've got a big box of old veneer off cut so I was just trying to find something that was
suitable. After trying quite a few veneers I decided that the the oak would be the best once
it was stained so all I'm doing here is I'm just neatening up the damage just by cutting it nice
and straight and then it's just a case of cutting the appropriate size piece of new veneer and
sticking that in. Just make sure that the cut you do is nice and clean and free from any adhesive
all the dust that you possibly can I do that with my vat just to blow the dust off and then wipe it
over with mineral spirits and then it's ready for stain. I'm using my Morel's alcohol-based
penetrating stain and again this is another two-tone piece this is the the walnut colour
and the majority of the Bureau is going to be in this colour but you'll see shortly it will have
got a dovetail joint then I am either going to paint it or I'm going to stain it. I just really
like how it adds that little bit of detail to it. I'm just pointing out here some of the sort of
overlap of the the walnut stain onto the area that I'm going to do in a different colour
and it's okay that's why I did the centre parts first so I could just sand back those solid
bits. The next colour stain I'm using is the ebony again it's a Morel's alcohol-based penetrating
were solid oak and they had a lovely rebated section in the middle so I just removed the old
finish, give them a sand, just clean them up and then I did the two-tone design on the handles
just to pick out the two-tone design of the Bureau. The plan for these hinges was to strip off the old
finish, clean them up and then spray paint them but you'll see in a second once I've removed that
old finish and cleaned them up they were absolutely beautiful and they stayed like that with no spray
paint on them at all. The top coat I'm using is a water-based poly by a company called Polyvine.
I'm just spraying that on, it's my sort of go-to top coat if I'm using a water-based poly.
It just goes on really nice and I get a really nice smooth finish. So usual procedure I spray
with light coats, wait for it to dry and then knock it back with a brown paper bag just to
take off any dust nibs and then it gets another two coats with a rub down in between each coat.
All the drawers were pretty dried out so they all got a treatment of the Howard's
Feed and Wax just to nourish them and protect them. The little drawer, the little pen drawer
from inside the unit had a bad ink stain on it and I couldn't get rid of it so I decided to cover it
with some nice green felt. Not only did it cover the stain it just made it look so much better as
well. It looked like it was always meant to be there. Just the last few details now and I'm using
some black Rub and Buff just to add some black to some of the details of the unit and that's pretty
much it. All I need to do then is add the handles and we're done. So I'd just like to say a massive
thank you if you've stayed this far and if you feel like I've earned it please subscribe, like
and share the video. It really helps out the channel if you like it and hopefully you enjoy the final reveal.