In The Creation Room at Mary Fox Pottery: Crawl Glaze Flower Bowls

Ceramic Art Studio
35 followers
1 Video ViewยทOct 4, 2025
Alrighty, so hello. Some of you have been asking whether I would do some videos showing how I glaze
my pieces and honestly that always just sort of seemed a little bit problematic for a few
different reasons. However, I have thought it over and I thought well the easiest piece for me to
really cover a whole bunch of bases as far as glazing and the crawl glazes would be the flower
series which are these. There's quite a few different styles that I do with this but today
I'm going to throw this form. With this video I'm going to take you through all the different steps
in its process till we end up with a bowl somewhat like this with the layered up crawl glazes. After
you've practiced a few times doing this technique then you can start to branch out with your glazing.
For instance, this bowl here is done with a crawl glaze over top of a shiny glaze. Now
this is a terra sigillata and when you're putting a crawl glaze over top of a terra sigillata that's
just been low fired it's a much easier application because there's a lot, you know, the absorbency is
easy. It's sucking up the glaze whereas when you're putting it on top of a glaze surface it's a bit
more of a challenge. So I'm not going to be showing you this. This is sort of something for you to
work up to but lots of different possibilities. This bowl here is another one from my flower
series and this has a base drop of the black terra sigillata which you see here. This is a
recipe I got online. It's basically cedar height red arts clay and then some oxides mixed in and
it's a very common black slip so you can you can find the recipe easily. So this slip is brushed
on this piece and then the crawl glaze has been applied, the purple one, and it's been fired and
then the white crawl glaze was poured in the interior here and sprayed lightly on the outer
edge and then fired again. So that's how that one was done. I won't go over how this was done because
I'm going to actually demonstrate that but how about we go and throw a bowl to start.
I've got six and a half pallets of clay here. I'll just get it centered and off we go.
Keep it centered. Now with the flower bowl I always leave a little bit of more depth at the bottom for
the center part of the bowl because it's going to be a slight curve like this.
It will all be revealed. Let me see how much room am I leaving down there. Okay got it that thick.
That's plenty. So now I'm just going to pull it apart a little bit. I left the extra thickness
there because once I pull this up we're going to make that nice little dish be the petal part of
the flower. So we need a little extra depth. So now I'm going to start pulling up and out. Now
one thing I find problematic when I get to the glazing stage of this form is if there are any
throwing rings they really show if you're making a pattern on the bowl. So I'm really mindful of
all the way along taking out the rings as much as I can. So now I'm going for my second pull.
Now that's pretty good. Nice and thick. So now I'm going to tear my rim. So whip it whip it good.
You usually end up doing this a couple of times depending. That's good enough for our first start.
Okay now I'm going to go back and do another pull. Now you can see I really had to grab the clay there
so there's those pesky rings which I didn't actually mean to get quite as pronounced but
be that as it may. Sometimes do this while you're trying to take those rings out.
If you just give yourself a little bit of support on the outside while you're pressing
and basically carving the clay away. I find that often once I get to this stage just very
calmly slowly going down from the top will help work those rings out. It's almost like you're
pressing a little clay into it but you have to be really cautious because if you're too thin at this
point you know what's going to happen. You're going to collapse your bowl. The best thing is not to have
too many throwing rings to start with but clearly I did not succeed at that point. So there we go.
So now I've got the basic shape without too too many rings. Take those out a bit more. Now I want
to make the center part of the flower and because we have that extra clay at the bottom it's really
quite easy to make a nice little dish there. Then go back bring this down a little bit. Let's tidy
that up and there's the center part. All done. Okay let's see what the thickness is now. It'll be
interesting to see how much we ended up going down. I don't think we went down that much.
Oh my lord no. There's still lots of clay there. Okay so I still have almost as much clay as when
I started but that's okay because we can trim that out nicely. You want to have extra anyhow
for the foot so you can give the piece a nice lift. I'm going to go for my final pull. I'm looking
at my torn edge and at this point in time if I want to do more to it this would be when I'm doing
it but it's actually looking pretty good. So even an old perfectionist like me is actually
relatively happy with that. I'm going to keep my fingers as flat as I can on the inside so I don't
make more rings and my focus is going to be on flaring it out as much as possible.
Notice I don't have the wheel going at the speed of light. I'm just curving up a little bit there
to get my rim the way I want it. It's looking better. I'm feeling pretty happy with that.
This is a raku clay body so it can take a lot of abuse and this is actually a Seattle Potter
Supplies raku clay body. I also use Laguna Industrial Raku which is a really nice clay
body to work with as well either or and often I like to mix a little bit of WSO in for plasticity
about 20% but that's because I have a pug mill and I can do all those things. I'm going to take
the rings out again say this is clay is starting to feel like it's going to slump on me at this
point I could stop because you know don't want to lose the bowl and come back when it's put the back
on the wheel when it's firmed up a bit and deal with the rings then when it's sort of leather hard
but I'm pretty sure I can get away with it so I'm going to do the best I can to
take those rings out move to a slightly smaller rib my hand on the outside there for support
I'm going to do one more from the top. Know when to call a halt it's time to stop before I
make a boo-boo. Let's seal up the clay okay so don't forget if you're feeling a little panicky
at this point just stop and do this when it's set up a little bit because you know you don't
actually need to do it now you can wait and prep for trimming cut line now I'm going to cut it
through so there's step one the bowl the bowl is made now I'm going to show you how we trim these
I threw this yesterday a little bit uh smaller bowl probably only about five pounds wet
and I have a nice piece of foam I'm just going to put on that to protect that torn rim
beauty and there's that bit that I cut through so it doesn't leave as much
that's pretty good so you remember that we've got a little bit extra thickness here so don't
be too concerned about going through it because you've got a nice heavy bottom so you can trim a
I always think that the bottom of the vessel is
really an important part that it sometimes gets a little overlooked
and really a nicely turned foot is what is kind of the pedestal that your
your vessel is standing on and always remember to bevel your edge
really helps with the bottoms the foot not getting chipped over time as people
you know don't lift it straight up the bowl kind of rock it there I think we've got a really nice
curve it looks good to me now seal up the the torn surface
Michael Sherrill's beautiful mud tools they know I'm always waxing on about these tools but really
they are just lovely I have just have to go over this a few extra times because
that Raku clay is really gritty so I've got a few little tears there trying to seal up
okay all done for this stage just one important detail left
the all-important signature there we go
so now this is going to dry and then when it's bone dry
is when I apply the terrace edge which I'm going to show you now
I've already put one layer of the terrace edge on here because sometimes I find if I put on
enough all at the first go of this terrace edge to make it black enough if I'm not careful and
if it's a little thin up here I can get some cracks so I just do a initial layer
and then let it sit one thing I've discovered about the terrace edge is that it's very
unforgiving for fingerprints when you go to pick this up afterwards like when you've got the slip
on there already sometimes your fingerprints can show so what I'm going to do is I'm going to leave
putting the final layer of this till after I've done the outside I'm just going to
gently turn it over on top of a chuck so now I'm putting the sigillata on and when you're
working with sigillata at first it's quite a learning curve there's all sorts of things that
can go wrong you can have the sigillata a bit too thin you can have it a little bit too thick
you find you haven't brushed it on enough and the clay color is showing through so really
careful observations observation rather patience with yourself and just know that
it's a learning curve and I have been doing this for like how long and I'm still making
mistakes with sigillata now this is fairly thick so I think I'm probably only going to need
about four layers I'm not seeing the clay shining through so I think I'm good enough
I have this bottle of water and I'm always using it to rinse my brush out in so there's a bit of
the brown sidge in there and I just I want a little bit of a little bit more water in my last
coat so I've rinsed my brush out so I know my brush is holding a bit more water now and I'm
giving it one more one more coat so it's just a little bit thinner and it's going to make it nicer
to polish you can be really deceptive with this slip you think you've got enough and then it comes
out of the kiln and you you're like oh god I can see the clay coming through and that really
nothing chokes my oats more than that I'm like oh god beginner's mistake age 63 still making
beginner's mistakes I'm not that great at self-forgiveness for my beginner's mistakes
so there we go now quick like bunny you get a little swiffer wait until that's that's dry
this is how you get that nicely burnished surface so you notice I'm I'm waiting until I can see that
that dampness is gone because otherwise it'll just end up grabbing on the on this okay so now I've
buffed the outside so this is this is pretty much done you could let this sit for a little bit
because the clay is a little bit damp and you want that to to dry out more notice how I'm not
touching that surface okay so I'm just careful down every time you're making a mistake and you're
feeling bad about yourself just remember me saying that I have learned the hard way over and
over again because I seem to make mistakes more than once so now it's all done and it's ready
to go in the kiln I'm going to put it on a on a bat so I can carry it to the kiln room on that
and then when I go to put it in the kiln I'm once again going to use these
in there so next time you see this I'll have taken it out of the kiln and we'll be putting the first
layer of glaze on it
all righty so we're back to the flower bowls they've come out of the kiln with their first
layer of the black slip on and I was just going to do one glaze combo for you and then I realized
that if I did two with two different combinations of crawl glazes I could better illustrate how the
crawl glazes react to the oxides that you put in them so I'm doing two so this one I'm going
to put my green crawl all these recipes and more information on how to use and fire them is in my
my life as a potter so you can you know all the extra tips are in there but in the meantime I'm
putting the green crawl with six percent copper oxide in as the first layer so I'm going to put
a thick layer for the flower center then once I've done that I've got my glaze in a handy little icing
thing you can get these at kitchen stores so I have the glaze in there and then I'm going to do the
first layer of the patterns so now the trick is how much glaze to put in the center because
you don't want to have to scoop it out so it's a bit of a bit of a guessing game
glazing is a lot like cooking it's uh instinct so I can already see that there's a good chance
that I was going to say that I don't have quite enough but oh my god look at that
and the more you work with these glazes you kind of get a sense for how thick to go
the beautiful thing about uh doing these on a bowl form they're not going to flake off onto
your kiln shelf because obviously when you're doing them on an upright form and that crawl
starts to shrink it can pop off it can pop off when it's drying it can pop off in the kiln
uh basically they're they're temperamental um kind of like me sometimes I write about that in
the book not me being temperamental about the glazes okay so now that's setting up nicely
now usually I do this over the sink in the studio but that wouldn't make as pretty a shot for you
so I'm going to do it here okay so there's sweep number one turn it around and I'm going to have
to practice self-forgiveness because of course when I'm on camera I never do as well as when
I'm just winging it by myself whoops okay so now that's the first layer now you can see how I've
got it thicker in some spots but I know from experience that going over and getting it a
back and I'm going to do another scoot through and I'm trying to follow the lines that I already
put there there we go okay last one whoops okay so now we've got all sorts of different
thicknesses happening I'm going to put just another little bit extra glaze right in the middle there
and I'm going to just coax that I'm going to try coax that around a little bit
there we go just so we get a little bit of variety because you know everything looks completely
centered and everything in nature but it isn't necessarily so I think I like that so now this
is just going to dry and then it's going to go back in the kiln for another firing I bisque fired
it to 06 my next firing is going to be 06 as well keeping it low and then when it comes out
and we put the next layer of glaze on it that final firing will be 05 okay so that's the green glaze
now I'm going to show you the purple blue glaze next because it has cobalt in it as a colorant
and it shrinks very differently all right so this is my uh blue slash purple crawl glaze like I say
it's this is like glazing is you go on your instincts and this is a new batch of glaze and
I can already tell I've got a little bit more water than I'd like in here so it's a little
runnier um which means it's going to shrink differently so I am going to um pour the glaze
and then probably go over it a couple times and try and get it
thicker so there's my yeah you can see how see how much quicker that one is going around
even it's just that first little pour there compared to the green crawl which was just
that much thicker so we already know we're gonna need to put a bit more in here all righty
oops it's not a very assertive pour now I'm just gonna let that set for one sec okay
I think I can get away with turning it now you can see the difference having too much
water in the glaze um is making to my pour so um well in a way this is good because it shows you
a I'm not perfect well I think you all know that already um but it also uh gives you clues as to
what to watch for okay let's do the next one oh geez there went a little splat okay
so we're definitely going to go over this a few times because we already know it's not thick enough
and uh it's not looking that exciting to me so I'm gonna go to town and just give it a lot more glaze
now you can see how because the glaze is running it's runnier it's it's moving into the flower
center so that's not going to be the end of the world because we're going to put another
glaze over top of this um but it does change how the the end product is like I'm saying now it's
not going to be my finest hour but I've said that before and then looked at a pot after it's come
out and gone oh my god you're fabulous so when this happens I generally let them run and then
I'll put a little dab in the middle join the runs up there so see how I just kind of coaxed it
I coaxed it all in and I'm gonna let that sit for a couple of minutes and then I
I might put a little bit more on but I think for um today to teach you that's probably enough
the next time you see me these are going to be out of the kiln ready for the next layer of glaze
so here we are back again uh both the bowls have gone through the the firing process
uh to oh six I did two to show you how the oxides react differently and I'm really glad I did
because this bowl turned out so nicely that I really don't want to put another layer of
glaze on it I think it's finished uh so this is the copper uh roughly about six percent
copper carbonate in my basic white crawl glaze of the recipes in my book uh but without the
so basically the crawl glaze base with six percent copper notice how the cobalt carbonate
has responded really differently first off this would have been a bit thicker than than this
but I never get the copper beating up it's always flatter platelets uh whereas when you put the
cobalt's more of a flux uh so I presume that's why I'm a scientist believe it or not uh so I
don't actually know but I'm presuming that that's why the cobalt beads up like that very very
different hey same base glaze very different textural reaction so we're going to leave that
as it is because we're very happy with it now this one I'm going to put some white crawl here
let it thicken up a bit and then I'll do the the splash once again over the top this is always a
bit of a guess as to how much glaze to put in there because obviously you don't really want
to be pouring it out so I'm going to want it fairly thick like that I can always add a bit
and then I just gently
gently
those big bumps are oi meaning that it's just not uh flowing as smoothly as it could
call these fox side effects I want to go up to that line but I don't want to go over
I think this one's going to turn out really quite quite cool good so now I'm gonna
do the squirt squirt squirt and you have to wait a second because you don't want it to just
run all over the place I did not get a very nice sweep there not quite sure what was happening
well let's hope for better this time it's always a little odd when you're demonstrating
all right so then you see how it's already drying and and setting up there you want to
let it set a little bit and then I'm going to give it another layer so right now trying
to smoothly go over where I've already been emphasis on trying this is a fairly uh fairly
deep bowl it's not as shallow which does make it a little bit more challenging
so now we're all done it's going to go in the kiln fire it for its final time hopefully it
looks magnificent and not um un-magnificent okay uh bye for now oh wow okay so this turned out
pretty cool uh I can see that I went pretty thick on the white crawl here because it's
separated a lot and you can see these gaps in between uh looking at this now I'm thinking I
might be tempted to do one more firing on this uh and put the purple crawl in here not quite as
thick and then what'll happen is it'll go into these black crevices and be a brighter purple
sort of poking out through that and then you'll have this these tones as well so I think that
might make it just a little bit more dynamic uh so I'm pretty sure I'm going to do that uh these
turned out quite nicely as you see everything worked the great thing about these glazes is if
you go a little too thick oh well not the end of the world go a little too thin that's a bit more
of an issue um but you just play and that's how you learn so this is the end of the video I hope
you've enjoyed it and if you want to learn more about me and the glaze recipes and more techniques
they're all in my book uh my life as a potter which is a fundraiser for my legacy project so
I hope you buy it and pot on oh and explore and experiment okay bye
