Mistreated 1904 Gilbert Antique Mantel Clock (Restoration)

Historical Horizons
11 followers
#restorationvideos #patina #asmr
Next up on the bench is a mistreated 1904 8-day Gilbert “Congo” antique clock. This clock has many issues and requires an extensive overhaul. Watch my step-by-step process of how I give this clock a second chance.
Next on the bench is a Gilbert Mantle clock from 1904.
And this clock's got quite a few problems.
So stick around and watch how I give this clock a second chance.
So I took a risk and I bought this clock from eBay,
knowing full well that I probably won't get what I think I'm going to get.
On the bottom of the clock there's a label that says Congo,
which is the model for this particular clock.
Let's go ahead and get it opened up.
And right off the bat we have our first problem.
The glass door is extremely loose and doesn't open or close properly.
And this is the key that came with the clock.
And the time and strike side do wind correctly,
but it's not a double-ended key so I can't adjust the beat rate.
So I'll have to find a new key.
So the back of the case has some really interesting bits of information.
There are a couple stickers that say EA Hammond watches and some other things.
But this metal cover plate says bought February 1904.
And scribbled in pencil, when the light hits it just right,
you can see that it says February 1904.
And in the corner it says number 7556724.
But later on in the video I'll get more into the historical context
and significance of some of these markings.
So let's go ahead and get the bob put in and see if this clock ticks.
And it ticks, so that's good.
But I can't help but notice how filthy that movement looks.
Let's see if it chimes at the 30 minute mark.
Yep, so that's good.
And let's see if it chimes and how it sounds at the hour mark.
So that sounded a little harsh to me.
And that leather tip looks like it's seen better days.
So I'll have to take a look at that.
Let's go ahead and get the hands and dial off.
So like I mentioned earlier, I bought this clock from eBay.
And the seller put in a listing description.
And I quote,
The movement was cleaned and oiled.
The clock comes complete with the pendulum and key.
And the case and dial are all original and in good condition.
I don't accept returns.
Well we know most of that was completely false.
Probably except for the part where he doesn't accept returns.
We could tell that the movement wasn't cleaned at all.
It had a really dark film all over it.
And it came with the wrong key.
And the glass door was extremely loose.
So let's take a look at what's going on with this door and why it's loose.
So it looks like it was soldered at one point.
And the solder joints have completely broken.
So I'll have to take a look at that later and see if I can get that fixed.
So I can tell right away that this clock was worked on back in 1976.
And I know this because Lowell B. Moore from Fairfax, Virginia etched it into the movement.
And I thought it would be really cool if I could try to find this person
and have a conversation about clocks or this particular clock.
So I did some digging online and I found one person by that name in Fairfax, Virginia.
So I tried calling and texting and unfortunately he never responded for whatever reason.
There could be many reasons why.
But let's go ahead and get this movement out of the case.
So one thing I'd like to mention is I recently purchased some assembly posts
which help keep the movement raised up off the desk as I'm working on it.
And I was able to get these because of your guys' support.
So I really do appreciate it.
Oh, what do we have here?
That's right.
I want to take a moment to thank Surfshark for sponsoring this video.
Surfshark VPN effectively hides your online activity by encrypting your internet traffic.
Not only this, if snoopers or hackers try to look,
it'll appear as if you're located somewhere else entirely.
Even on the other side of the world if you want.
By using Surfshark VPN or Virtual Private Network,
you establish a secure virtual tunnel between your device and the internet via a VPN server.
This tunnel is then used to transfer all of your internet traffic.
This helps keep your online activity private,
block ads, trackers, malware, and protects all your devices at the same time.
Reducing price discrimination is another great benefit of using a VPN.
Some websites use your location and cookies to tailor their prices.
With Surfshark VPN, you can avoid these marketing practices
and save some money when shopping online.
With the money you could save, your Surfshark membership could easily pay for itself.
Surfshark also creates other privacy and security products
that protect your personal information online,
defend your devices against viruses and malicious software,
and guarantee the security of your emails, credit cards, and other sensitive data.
Visit surfshark.com slash watchoverhaul to get an exclusive deal.
Four extra months free.
With a 30-day money-back guarantee and 24-7 customer service,
there is no risk giving Surfshark a try.
All right, so let's get back at it.
So another thing I got is a new microscope.
So let's take a closer look at this movement and see how things are looking.
And here's a closer look at Mr. Moore.
All right, let's keep moving around the movement and check out some of these pivot holes.
And you might notice some scratch marks surrounding some of these holes.
And this one's actually got some punch marks as well.
And sometimes when people are working on rebushing a clock,
they'll make a mark next to the hole in the direction of the wear.
And this helps with drilling the new holes to insert the bushings.
And I'm not a huge fan of marking up the movement like this.
So if I were to do this, I would probably use a marker and then erase it after I'm done.
So from what I can tell, it looks like most of these pivot holes on this movement
have already been rebushed.
And I couldn't find any that looked like they needed to be rebushed again.
I mean, they don't look necessarily pretty when you're zoomed in like this.
But they don't look worn out to me.
They're dirty, but they don't look worn out.
So one of the most important steps before disassembling a movement
is letting down the mainsprings.
And if you forget to do this, you're probably going to get yourself hurt
and damage the movement in the process.
So what I like to do is surround each mainspring with a couple zip ties.
And then use a let down tool to unwind the mainsprings.
So before I can unwind the mainspring, I have to move the click spring out of the way.
And what I'll do is I'll start to wind the mainspring a little bit.
And that'll move the click out of the way.
And then I can unwind the mainspring.
And when you wind a clock and you hear that clicking sound,
what you're hearing is that click pressing up against the ratchet wheel on the main wheel.
So before I move on, I want to measure these arbors
so I can try to find the correct double end key online.
And I'm going to measure in a few spots because these are tapered.
And sometimes the measurements are different depending on which direction you're facing.
So it looks like these are about 3.8, 3.9, something around there.
This is in millimeters.
And I'm going to measure the beat adjuster here at the top.
This comes to 1.79 in that direction.
And about 1.9 to 1.95 millimeters in the other direction.
So I looked online and I found a key that I think will work.
It's 1.95 millimeters on the small side and 4.25 millimeters on the bigger side.
So I'll get that ordered and wait for that to come in.
All right, so now it's time for the fun part and sometimes pretty stressful part,
which is completely disassembling the movement.
And I ran into my first problem right away,
which is the suspension spring is pinched and stuck in the beat regulator and I can't get it out.
So I'm just going to have to leave that in there.
So what I'm going to do is just spread open the crutch a little bit
and pop out the suspension spring rod.
And there we go.
And I'll just pinch that back so it doesn't catch on anything.
And let's keep moving forward.
So there are four nuts holding these plates together.
And I noticed there's one in particular that's smaller than the rest of them.
But this nut that I'm removing right here is the same size as the nuts used on the plates.
So what I think happened is when someone reassembled this movement last time,
they accidentally used the bell nut on the plates and used a plate nut on the bell,
which isn't a huge deal.
But I'll fix that when I go to reassemble everything.
Man, I just can't get over how dirty this movement is.
I mean, look how black and dark some of these parts are.
It's my guess that someone probably sprayed something like WD-40 on the movement,
which is something you definitely don't want to do
because it does things like this and it gums up the wheels and the pivot holes.
I don't know.
What do you guys think?
Do you think someone sprayed WD-40 on this movement?
So when I separate the plates, I try to do that very carefully
so I don't make a huge mess of everything and wheels go flying everywhere.
I did drop the escape wheel, but I'll put that back just for reference.
And then I'll just work my way through the movement,
removing and inspecting each part.
And you might be wondering how I remember where everything goes
when I go to reassemble everything.
Well, what I do if I run into problems
is I'll reference the video that you're watching right now
and I'll know exactly where I took something off and where it should go back.
So another big thing that helps me with knowing how to reassemble a clock movement
is actually taking the time to figure out the anatomy of a clock
and the relationship between all the wheels and levers and things like that.
And over time, I'm finding that I'm starting to recognize particular wheels.
Like I can look at a particular wheel and go,
oh, that's the fourth wheel and that typically goes here.
And this is the escape wheel and that typically goes there.
And so that's what I've found has been the biggest help for me.
So the last thing to remove is this beat regulator assembly.
And I actually found some really cool patent information
about this assembly that I'll share with you guys later on in the video.
And this is what a completely disassembled 1904 Gilbert clock looks like, which is pretty cool.
So before we move on to actually cleaning the movement,
I want to go back a little bit to these stickers that are on the back of the case.
So I want to share with you what I found out about E.A. Hammond.
So I did a little digging and I landed on the Mechanic Falls website
and I noticed there's a Mechanic Falls Historical Society.
So I reached out to this community to help point me in the right direction.
And I want to give a huge thanks to Erics and Belinda
for pointing me to this paper from 1913.
So I'm going to zoom in a bit here and we're going to find out
a little bit more information about E.A. Hammond.
So it looks like in 1913, he accepted a new position at a bakery in Auburn, Maine.
But when he first got to Mechanic Falls, he was the owner of a barber shop
and a jewelry repairing shop.
But he sold it out because he was having some health issues.
So from reading this article, it looks like E.A. Hammond was very active
in the community.
But I wanted to dig a little bit more and see what else I could find out.
So I went back to the website and I found this document titled
The Mechanic Falls Register of 1904.
And I thought this was interesting because someone wrote on the case
that the clock was bought in 1904.
So I searched this document for Hammond and I got a couple hits.
The first one says that he was a jeweler.
And the second one says he was a barber, which matches the article we just saw.
So it's my guess that this clock probably originated from his shop.
All right, so let's get back at it.
So this is a mainspring winder that I made.
And a link should be popping up right about now
to a video that shows how I made this mainspring winder.
So before I start cleaning everything,
I need to get these mainsprings separated from the main wheels
and get the mainsprings cleaned and lubricated.
And you always want to remember to wear a face shield and a leather glove
when you're dealing with these mainsprings
because they can be a little unpredictable sometimes
and you don't want to get yourself hurt.
So before I actually start to unwind the mainspring,
I have to wind it up a bit to relieve some of the pressure off those zip ties.
And then I can get these cut off and then unwind the mainspring.
So it looks like this spring is pretty set,
which is typical for some of these antique clocks.
And this can happen if the spring is in a compressed state for a long period of time
and it will lose some of its ability to expand.
So this is an eight day clock.
So this means that the clock might not run for a full eight days
because it just simply can't provide the power that it needs to run that long.
So now I need to separate the mainspring from the main wheel.
And there's a pin on the side of the arbor that's inserted into a hole
on the end of the mainspring.
And the trick is to get that pin to pop out of that hole.
So what I'm doing is rotating the arbor as if I'm unwinding the mainspring
and hopefully the pin just pops right out.
And in this case, it did.
So if you look here, there's a hole on the end of the mainspring
and the pin that's on the side of the arbor goes into that hole.
So now it's time to clean and lubricate the mainspring.
So I'm going to get it mounted into the vise and use some steel wool and WD-40
to clean all the dirt and grime off the mainspring.
And typically you don't want to get WD-40 anywhere near a clock.
But in this case, I'm just using it as a cleaning agent.
And I'm going to wipe it all off before I lubricate the mainspring.
All right, so now it's time to lubricate the mainspring.
And what I like to use is this Keystone mainspring lubricant.
So I do want to point out that you can buy new mainsprings if they're set like this.
But this is just going to be my own personal clock.
And I like to keep them as original as possible.
So I'm not that worried about it.
But if you had a paying customer, you'd probably want to have a conversation with them
and ask them if they'd like to keep the spring original
or go ahead and replace it with a new spring.
All right, so this spring looks pretty good.
Now I just need to do the same thing to the other spring.
So with this spring, I am having some issues with popping that pin out of that hole.
So what I'm going to do is use a flathead screwdriver
just to pry that innermost pin out of the spring.
And then I'll try to rotate the arbor like I'm unwinding the spring
like I did on the other one.
And hopefully the pin pops out of that hole.
And there we go.
It just popped out.
Looks like this spring is pretty dirty.
So in my last video, I used Crystal Simple Green in my ultrasonic cleaner
and I had an issue with some of the parts turning blue or purple.
So this time, I'm using Deox007, which I bought from Time Savers.
And this solution is also highly recommended for cleaning clogged parts.
The bottle says to use a 7 to 1 ratio with water.
So 1 gallon of Deox007 can make a total of 8 gallons of cleaning solution.
I also decided to reduce the temperature and cleaning time.
So hopefully this fixes the problem that I had last time.
Wow, look how nice these came out.
So now I'm just going to use some mineral spirits
and clean off any leftover cleaning residue
and dry everything off with a heat gun.
So I want to take a moment to give a special thanks to these folks
for clicking that thanks button that sits just beneath the video.
It's because of your support that I'm able to purchase new tools,
accessories, and clocks for this channel.
You know, I reinvest 100% of the money I make on this channel back into the channel
so I can continue to make the best videos that I can for you guys.
So thanks again and I really do appreciate it.
But if you're looking for more ways to support the channel,
I enabled channel memberships so you can now become an official member of the channel.
As a member, you can get member shoutouts, early access to new videos,
photos and status updates, and more.
There are three levels to choose from and each level builds on the next.
The first level is called On The Verge,
the second is Hands On,
and the third is The Works.
I hope you're as entertained with the play on words as I am.
To learn more, go to youtube.com slash watchoverhaul slash join.
I just realized that I'm missing one of the smaller screws and this is where I found it hiding.
I've had this happen before and I remembered that this toothbrush
gets pretty hungry sometimes and likes to eat some of these smaller parts.
So
okay, so we're finally done cleaning the movement.
So now it's time to reattach the main springs to the main wheels.
And the trick is to get that pin on the side of the arbor to go back into the hole
in the innermost coil.
And then I'll rotate the arbor like I'm winding the spring
and hopefully that pin catches in that hole.
And it looks like that's working just fine.
So now it's time to wind the main spring back up.
So now that the zip ties are in place, I can unwind the main spring just a bit
and let the zip ties hold the main spring in place.
And I didn't unwind it enough and the zip ties weren't as tight as they should be
around the spring and that's why it jumped there at the end.
So now I'm going to get the other main spring reattached and secured to the main wheel.
And then I'm going to show you some before and after shots of what the movement looked like
before cleaning and after cleaning.
And the results are pretty amazing.
Just look at some of these before and after shots.
I'm just really impressed with how well this cleaning solution actually worked.
And I'm thrilled that none of the brass turned blue or purple like it did in my last video.
So before I can reassemble the movement, I need to figure out what's going on with this hammer.
And I was messing with it off camera and I accidentally broke off the leather tip.
And I was planning on replacing it anyway, but I definitely have to replace it now.
So I have this leather cord laying around from the last time I had to fix a hammer
and it should be the correct diameter.
But first, I have to remove this old leather from the hammer.
And this process took me a long time to do.
Nearly 30 minutes or so I would say.
But don't worry, you don't have to sit through 30 minutes of me fumbling with this.
I did speed it up quite a bit for the video.
So you should only have to watch about a minute of it.
But what I found worked the best is just using this razor blade and picking at it until it all came out.
All right, looks like we're getting close here.
Looks like just one more piece to get out and that should be it.
Now I'm just going to cut a piece of this leather cord.
And I'm going to cut it a little longer than what I actually need.
And then I'll cut it down to size after I get it installed.
But first, I'm going to try to soften and taper one end of this cord
so it goes into the hammer just a little bit easier.
And I'm just going to try to use one or two drops of CA glue in the hammer
just to make sure that the leather tip doesn't fall out.
So that went in pretty good.
So now I'm going to try to see if I can pull it out and hopefully it stays in place.
The goal is just to make sure that it doesn't just fall out.
But I'm sure if I pulled on it really hard, it would come right out.
So now I'm going to cut it down to size based off of how I remember how long the tip was.
But after looking at this, I think it's still just a little bit too long.
And I went back and looked at some reference pictures and videos
and it is just a little bit too long.
So I'm going to cut it down just a little bit more and see how that looks.
All right, I think it looks pretty good now and hopefully it'll sound a lot better.
But first it's time to get the movement reassembled.
So one of the techniques that I still need to learn how to do is polishing the pivots.
This is something that I still haven't figured out the best way to go about
but it is something I plan on figuring out at some point.
So one of the last things I like to do before I finish a clock
is make sure that the beat rate is dialed in just right
to where it's not beating too fast or too slow.
And this beat rate, or the beats per minute,
can be calculated by looking at the wheels and the path from the center wheel to the escape wheel.
And I count the teeth and the pinions on these wheels
and I do a simple calculation to figure out
what the theoretical beats per minute should be for the clock,
which comes out to 152.82.
So this number will give me a target to shoot for.
If I'm higher than this number then the clock is beating too fast
and if I'm lower than this number then the clock is beating too slow.
All right, so now it's time to put the plates back together
and this is where things can get pretty frustrating and time consuming
because you've got to get all the pivots back into their pivot holes.
So what I like to do is start in a particular corner
and try to get the pivots back into their pivot holes
and when I do I'll loosely screw down the nut so the plates don't separate
and then I just work my way around the movement
trying to get all the other pivots back into their holes.
And I recently purchased a new tool that I'm using for the first time right now
which is a pivot locator.
In the past I've tried to just shove my fingers inside the movement
to move the pivots around to get them to go back into their hole
but using this pivot locator helps out quite a bit
because I can get it in places where I can't get my fingers.
I also want to mention that if you're interested in working on clocks like I do
or you're new to it and you get to this part and something doesn't seem right
try not to force anything and just take a step back
and look at it from a different angle
and try to find if there's something binding up or not sitting correctly
and chances are you'll see what's going wrong
and you can move it around just a little bit and move on from there.
All right, so I finally got the movement reassembled
but to make sure I did it correctly
I really want to check out the strike side of the movement
because if I did that wrong then there's a high chance
that when the movement starts striking
it's not going to stop until the spring is fully unwound.
So there's a couple things I want to check and we'll get into that now.
So I just want to explain a couple things before I test this out.
Right here is the warning pin and right up here is the locking lever
and so when everything's working correctly
the locking lever should fall into the path of the warning pin
and should stop the clock from striking.
I also want to point out that the count lever that I'm moving with my thumb right there
should be in a deep notch
and the maintenance lever should be in the bottom of the maintenance cam notch
when the locking lever falls into the path of the warning pin.
So all of these factors have to be synced up
and if they're not then most likely the clock won't stop striking.
So let's try this out and see what happens.
So if I assemble the movement correctly
then the count lever should stop in a deep notch on the count wheel
and it looks like it's not stopping.
You can see that it dips down into the notch but then pops back out.
So something's not right.
So the problem is that the warning pin is too far away from the locking lever
and I figured this was going to be a problem when I saw this earlier
but I wanted to show you guys how to fix this.
So what I do is I'll loosen the nut just a little bit
and pop out only the warning wheel.
Once I get the wheel popped out I'll rotate the wheels
so that the warning pin is a lot closer to the locking lever
and then pop it back into place.
And I also want to point out that you don't want to do this
unless you have your mainsprings restrained in some way or fashion
because if you don't you'll probably get yourself hurt or break the movement.
All right so let's test this out again and see if it stops striking correctly
and if it works the count lever should stop in one of those deep notches on the count wheel.
And it looks like it's working.
And the reason it's working is because the warning pin is hitting the locking lever.
As you can see right there it stops the strike train from moving.
All right let's keep pushing forward.
There's still a few more things to reattach to the movement
and this next thing is what's called a clock regulator.
And this helps with speeding up or slowing down the beat rate for the clock
and it does this by raising or lowering the pendulum.
Something else that's interesting about this is there's a date of April 28, 1896 stamped on it
and I figured that's probably a patent date.
So I did some digging online and I actually found the patent for this exact mechanism
by Woodruff and McCabe with the Gilbert Clock Company.
And I thought this was super interesting so I wanted to share this with you guys.
So as you can see as I rotate the shaft the pendulum will actually raise and lower.
And look what finally came in.
A nice new shiny key.
Hopefully I bought the right size so let's give it a try and see if it works.
And now the clock regulator and that works too so we're good to go.
So now it's time to cut off the zip ties because we don't need those anymore.
So I'm going to go ahead and cut off the zip ties and then I'm going to go ahead and
wind up the springs a little bit and get those cut off.
So now I'm going to do one more test of the striking mechanism with it running at normal
speed.
And you can see that the hammer is striking so that's good.
And hopefully it stops in one of those deep notches.
And it does.
How about that?
All right so now it's time to oil the movement.
And by the way here's a better shot of this new microscope I got.
It has a lot of cool features on it.
One of which is autofocus which really comes in handy.
But I just have it plugged into my laptop to record video and audio and it works pretty
good.
So when I flip the movement over I realize the bell is blocking some of the pivots.
So I actually had to remove that again so I can get those oiled.
And now I'm just going to put a little bit of oil on the verge.
All right so now it's time to finally address this loose door.
But first I need to get everything clean with the exception of the dial.
I don't really want to touch that or mess that up.
So I'm going to take that off and get that out of the way.
But I'm going to clean the bezel and the glass and then try to address this loose hinge.
Hey look a bubble.
By the way I'm going to properly clean this glass with Windex here in a little bit.
So I'm going to attempt to fix the door by soldering the hinge back in place.
And there seems to be plenty of solder already there.
So I'm hoping I can just reuse what's already there.
But if that doesn't work then I'll just add a little bit more solder.
And I've only soldered things in the past when building circuits or repairing electronics.
So this is the first time I'm soldering something like this.
So what I'm going to do is add a little flux so the solder flows nicely and then hopefully
I can get the hinge secured again.
So let's give it a try.
Okay it doesn't look pretty but let's see if it works.
And the door isn't loose anymore.
How about that?
So I'm just going to smooth things out just a little bit more and call it good enough.
So I'm trying to tweak the hinge pretty hard here and it's not moving at all.
So I think we got this fixed.
So the last thing I'm going to do with this is clean the glass.
And I'm just using some generic glass cleaner.
And then we'll move on to cleaning the clock case.
So the case looks pretty good considering that it's from 1904.
So all I'm going to do is use some warm soapy water and clean the outside of the case.
So I just want to point out that the finish on this case could use a little bit more
tension than what I'm giving it.
But I couldn't quite figure out the best way to make it look better than what it currently does.
And I didn't want to risk making it look worse.
So I'm just going to wipe it down and try to get all the dust and dirt off of it.
But if you know the proper way to handle the finish that's on this case,
please let me know and I'll look into it.
Now that the case is cleaned back up, I'm going to go ahead and get the movement back in
and the dial and hands back on.
So I looked at where the count lever was on the count wheel
and it should be set at three o'clock right now.
So here in a minute I'll give it a test and hopefully
the next time it chimes on the hour mark it strikes four times.
So now I'm going to wind up the strike and the time side of the movement just a little bit.
And then we can get the bob put back on and see if the clock's ticking okay.
And then we can finally check out how that new leather tip sounds.
The clock seems pretty happy already but let's give it its bob back and see how it sounds.
It sounds pretty good at the 30 minute mark.
Let's see how it sounds on the hour.
Well, I think that sounded a lot better than how it used to sound.
What do you think?
So I use this app that listens to the bpm or beats per minute
which shows in the lower left hand corner.
And the number we're looking for is 152.82 to be exact.
It was showing around 153 so it's running a little bit too fast right now.
So now I'm going to rotate this to the left which should lower the pendulum
and then make the clock run a little bit slower.
So let's see what that adjustment did.
And it's still running a little bit too fast so I need to lower the pendulum a little bit more.
And let's see what that did.
152.85.
I think that's pretty close to 152.82 so we're going to call that good.
So I just want to take a moment to let you know that I really do appreciate you
taking time out of your day to watch this video.
It really does mean a lot to me.
And if you're looking for ways to support the channel
you could always simply like and subscribe and that always helps.
But if you're looking for more ways you could always click that thanks button
that sits just beneath the video or you could take a look at becoming a channel member.
Thanks again and take care.
