Throwing / Making a clay Pottery Cookie Jar & Lid on the Wheel

Ceramic Art Studio
35 followers
1 Video View·Sep 4, 2025
Hi folks, I'm just going to make a bit of a biscuit jar, a sort of storage type jar with quite a narrow top hopefully, with a lid on.
So, we'll give it a go.
I've got, what, about four pounds of clay here.
Quite soft as well, so it might not be the best for this sort of stuff.
So I'll just centre it.
So it's going to be a dead simple flat lid.
Because it's going to be a small lid, it doesn't need to be a curved one for any strength.
I'm going to leave it quite thick at the top, so I can put like a ledge in for the lid to sit on and I also want to keep it quite narrow all the time at the top.
I'll squeeze it in because it's going to be quite narrow at the base too.
I'll just collar it in again.
I'll just do one knuckle lift.
It might actually go out of shot.
I don't know where my camera is, I can't really see it.
I want to keep it quite narrow and thick at the top.
I'll slide it down.
So I may as well form the gallery now before it gets too thin.
Hopefully you can see.
I'm going to just use that finger and with that thumb just to sort of hold it there, I'm just going to push down and make a ledge like so.
So that's the ledge for the lid to sit in.
So now I'm just going to, from the inside out, just shake the pot.
Just open my fingers up and squeeze it outwards.
To put a bit of strength in what I'm going to do, I'm just going to put a little ledge in there with my finger, a bit like that.
I don't know why it is but when you put a little ledge in, it just tends to stop the top from flaring out any more than it needs to.
I don't know why it does that but it seems to work.
So I'll just make a bit of a nicer shape, just get a bit of a shoulder on it, a higher shoulder.
Push the gallery down.
So that's the pot made.
Pop it out.
It's not the best shape actually, it's a bit squat.
I've not got a very nice shape really.
So I'll just make a dead quick lid now.
Like I said, because the top's not very wide, there's no need to make a curved lid.
There's no strength needed.
So with the same old lid, I'll just flatten it out, centre it flat.
I'm going to make this lid a lot wider than it needs to be because I can trim it down tomorrow to make it fit.
So as usual, just push in and downwards and the knob should pop up like so.
And I'm just going to stretch it out by forcing it out like that to get it half an inch wider than I need it to make it.
Now with this one, I want to make a little pagoda shaped knob on it.
So what I'll do, push down away from the middle, which means a little nipple will pop up like so.
A little pointy thing.
Just gives it a bit of a different shape and a flat knob.
Like I say, I'll just trim this to size tomorrow to get it to fit.
So that's the knob with that sort of shape.
So the lid with that shape knob on.
And then tomorrow, I'll trim the lid to fit and it'll go on there like so.
Right folks, I'm just going to turn this jar now.
Trim it, whatever you want to call it.
So I'm just going to use my turning tools like that to get some of the throwing lines off.
I don't know whether you can hear that weather, it's absolutely blowing a gale and throwing it down outside.
I'm just going to do a bit of a chattering design on this one.
So I'll have to let it dry a touch so the cobalt slip will dry.
In the meantime, I'll just try and trim this lid to size.
I've let this dry out a bit too much actually.
It doesn't have to be that big.
It should be the right size.
A touch more off.
I don't know whether a bit of colour is off.
Like I say, I didn't let it dry a bit too much.
But we'll see.
That's hard.
No, it's alright.
That's just enough.
I'll just get this pot back.
See if it fits.
And it fits perfectly.
So I'll just do a bit of a chattering design on this.
It's not quite dry enough but we'll see.
A bit of proper chattering too.
So just basically let it bounce about on the clay.
Takes random chunks out.
And that's the design you end up with.
So that's about it.
Here's my jar finished.
With a lid.
I've just put a stamp on.
Like I say, I'm not very excited.
A bit of a cookie jar, biscuit jar, storage jar with a lid.
Done.
