In this video you will learn how I installed my Water Change System which allows me to perform water changes in my aquariums the fastest way possible! Plus you get a look at ARKA's brand new myAQUA 3800 Rerverse Osmosis Filter.
Buckets on Wheels Video: • Aquarium Water Change Station on Wheels!
I think I found the most simple way and also the fastest way to change water inside my aquariums
here in my aquascaping studio. So guys in today's video I'm going to show you exactly how I built
the system, which components I'm using and the routine how I change water fastest way possible
in my studio aquarium. Let's get started. To install the MyAqua 3800 I used a little hack.
I marked the holes at the back of the unit on masking tape.
This way it was much easier to find the right location to drill holes in the wall.
Next up I installed the Multifilter 4000. This behemoth contains 4000 ml of high quality resin
and will absorb whatever is left in the water. You see, in Germany we have relatively high silicate
in the tap water and this way I can get TDS zero, absolutely pure water. I have been using
the Multifilter before in my home nano gallery attached to the water change cart. But now it
finally will have its own place on the wall. I quickly mounted the power brick from the MyAqua
in between and moved on to the automatic water hose roll-up box from Gardena. Trust me when I say
you didn't know you need one until you see how comfortable it is.
With the hose box on the wall it was time to prepare the 300 liter water bucket. I knew I
was going to automate the refill but just in case it's always nice to have an overflow.
I drilled a hole and attached the tap that came with it right at the top of the bucket and connected
it with a super soft tubing from Chihiros to the sink. I know the tubing is way too long at this
moment, I will shorten it later. To monitor the quality of my reverse osmosis water I installed
an inline TDS meter. This way I can immediately see when it's time to replace the resin inside
the Multifilter. While the water was running and I have to admit the MyAqua 3800 is producing
a lot of water really fast. 2.6 liters per minute. I began assembling the Gardena pump.
This pump is probably overkill but it has a built-in auto switch. It detects when the tap
is closed and goes in standby mode. Once the tap is open it turns on automatically.
I decided to flush the pump before using it with our water and you can see how much power it has.
After everything was connected I flushed the Gardena tubing too.
This way I can be sure it's really clean and ready for use.
So guys now that you have seen how I installed all of this let me talk briefly about the Arca
MyAqua 3800 and why I love the system so much. First things first I mean just look at it it's
beautiful it's maybe the nicest RO system on the market. The pricing is very competitive both the
1900 and the 3800 producing blazing fast a lot of water very very quickly but the number one
argument why I love the system so much is how easy it is to maintain it you know to do the service
to swap out the cartridges and I think the best way to tell you is to actually show you. So let me
take out all the three cartridges plus the membrane and put it back in and we're going to
measure the time. Okay so first of all I have to close the water.
Water is closed then pull the power cable.
Power is out now I have to remove the pressure from the system.
Done now I'm ready to go basically take out first filter, second filter, third one
plus the membrane completely disassembled. Now I would get new cartridges new RO membrane
and then put everything back in again. Let's do that pretend I just swapped them out.
The membrane goes in first
then the C2 which is second like a final stage carbon filtration then we have
the first stage carbon filtration and the mechanical pre-filter.
Done what was that a minute or so I don't know you see it on the clock so fast loving it guys
the same thing with the I don't know classic RO system like some of my clients still have
that takes me an hour sometimes two hours and then the stuff is leaking. Yes this goes super
fast to swap out these cartridges but also they are a little bit more expensive than the regular
ones but Arca got you covered with this tool you can unscrew the bottom and then take out what's
on the inside so this ones are sold separately you can get both the combination pre-assembled
or just this one which is much cheaper you know invest those 10 seconds yourself and swap out
the cartridge inside this body screw it back together nothing compared with other systems
and now let's get to the routine where I show you how I actually change water
using all of this in one of my aquariums.
So guys there's one part missing in my setup and it's like a switch or toggle something that
refills the bucket automatically for this I see two options one would be a mechanical floating
switch you know like in the toilet where you know the water closes the refill but that also means
as soon as I take out just a tiny little bit or maybe there is some movement the you know the
RO system is triggered every so often I might not want that the other alternative is something from
which is an electronic switch actually two switches one at the top one at the bottom
so when the water level drops down as soon as it gets to the bottom switch
then it triggers the refill so let's say maybe at 50 the refill begins and then the top switch
says okay now the barrel is full no need more water and then it turns off turns it off with
the solenoid let me know which one you think I'm going to install and if you have any questions
about this whole setup let me know in the comments below thanks for watching and I'll see you in the
next one bye