Carved bed 2 part, wood carving

Eternal Sculptures
211 followers
2 Video Views·Aug 18, 2025
Hello everyone, I continue to work on the bed.
In today's video, I will be engaged in carving this central element of this thread.
As you can see, this is a more saturated thread, and the result is beautiful.
On the left, I have already cleaned the hard-to-reach places where I could not get in with a cutter.
I haven't touched the right yet, but I will remove it during the carving process.
I start with the central curls, I go through the line with a corner,
then I cut it with a chisel along the radius, and there is a cut in the direction of the curl.
In the same way, this element is made, and this element is also a cut, a cut.
Friends, I'm starting to work, and I wish you a pleasant viewing.
I finished with the central element.
As you can see, here I took off the chamfer a little, rounded it, also made the top cone lower.
If you look at this element, it turns out to be semicircular, and I bent it down more to the edges.
Now I want to do this with two curls, I will tell you now in height how it should turn out.
This is the top point, I will not go down, but if I go down by a millimeter, maybe one and a half,
but here I will go down stronger, somewhere I will cut 4 mm down.
And here it is even stronger, gradually, so as to go up to this level.
I want to tell you how I got these two curls.
I cut the straight chisel, as you saw, at a slight angle towards the exit of the outer part,
but I also took off the chamfer in a circle, it turned out not a curve, but almost a curve.
It looks quite interesting and beautiful.
Here I made a chamfer, the chamfer turned out to be in the form of this cutter.
So, I switch to these two chains with a brush, which is at the bottom.
Here I separate and lower them down, the closer to this element, the lower.
And on the chamfers, the chamfer will go here and here, but these long ones too.
Here, here and here, the chamfer.
And on the outer part, I will round them.
I'm going to cut along the radius of this curl now.
I have already picked up two chisels.
First, it will go more semicircular, such, first to the middle,
but then from the middle to the end it will turn out to be a more rectangular cutter.
Then I'm going to gradually bend down from here,
so that where they touch, all this chain with this curl,
it turned out to be about 3-2.5 mm in height.
Let me remind you, the depth of the milling is 7 mm.
After that, I will begin to separate all these leaves and curls from each other.
And not only did I separate these leaves from each other and from the curl, but I did almost everything.
I only have one element left.
This vegetation, by the way, is done according to the same principle as this.
Chisel, chisel, here is a chisel, and this part I will lower a little down.
Then I'll take care of this curl, I'll separate it here,
and from this moment I'll start lowering it down.
The closer to the curl, the lower.
Here I will make a chisel.
And by the way, this curl was done according to the same principle as this central one.
There is only a small difference.
From this moment on, I will round.
Yes, at this moment it will be as if semi-rounded, and then it will be rounded.
I'm going to finish this sheet, which is between these two curls.
I'll take the camera in my hand and show you how this thread looks at this stage of work.
In general, it turns out pretty well.
Such an interesting bed will come out.
The side elements are completely ready.
Only this central thread remains.
It is made deeper and looks more voluminous.
These curls will still need to be cut on the sides, and these leaves on top.
I will do this in the next video.
And that's all, friends.
Who liked it, put likes, subscribe to the channel.
Good luck to everyone, see you.
