Review of the Ryobi R18GN18 Nail Gun

Amazing Tools
4 followers
Even if a power tool speeds up the work should you really invest in it? Today I review the DIY Ryobi second fix nail gun to try to answer that question.
#machine #tools #Powertools
Today I'm going to be reviewing the Ryobi One Plus 18V 18 gauge brad nailer and asking that
question that we all have which is, do you really need one? This is the Ryobi R18 GN18
brad nailer which means it fires these really small thin brad nails for like finishing work.
18 gauge now 18 gauge is about 1.2 millimeters in width and you have to remember 18 gauge is
actually smaller than 16 gauge. It's all round the wrong way and it's all old-fashioned. All you have
to remember is 1.2 millimeters and it fires these in lengths of anywhere between 15 millimeters
and two inches which is plenty at both ends of the spectrum. I've never really felt the need
to use anything smaller or anything bigger. So let's have a look at the gun itself. Now these
cordless nail guns irrespective of make are all generally set up in the same way. There's the
dangerous end with the tip at the bottom and just above it you end up with the magazine that opens
with a bit of a clip. Now when you feed these sort of nails in they always go tip at the bottom
irrespective of what length they are. You always put them at the bottom and just move them forward
then it just closes with a bit of a click. Let me just take those out because I'll be fiddling
around with the tip now. So it can't fire unless that tip is depressed and don't worry I haven't
got a battery in it at the moment so it's not going to do anything anyway. So the tip needs to
be depressed and the gun needs to be turned on which I'll tell you about in a minute. Now I've
used this quite a lot over the last two or three weeks and I've not had any jams but if you do get
a jam this front plate just pulls forward and that opens that whole tip mechanism. If you do get
anything in there that's now jammed you can take all that out as long as you've taken the battery
off first of course and that just goes back in there and then clips back into place. There's two
things that you can adjust on this nail gun. The first one is the depth that the nail fires into
and I'll demonstrate that in a minute and I've used this quite a lot and I would say
it's pretty accurate and really easy to adjust finely. The other thing that you can adjust
is on the back here is a pressure setting. Now this is a little bit confusing because in the
instructions it will tell you that this increases and decreases the pressure in the gun however
to be honest with you it's not made any difference to me at all so generally I've just kept it on
the sort of mid setting. The other thing that it's got which is handy is a belt clip which I've used
a few times and it's got a light on the front and that light also tells you whether the machine
is on or off. So let's pop a battery in and I'll show you how to turn it on. Now there's two ways
of actually turning it on. The first way is to depress the head so if I just push the head then
you can see that light comes on. The other way of turning it on is that there's a second button here
not the main trigger but there's a second button that you use with your middle finger that also
turns it on. Now I thought originally that that might be a bump fire button but it's not. This
nail gun cannot bump fire it's only single shot only so that button in there also turns it on so
if I just press that you can see the light come on and it's ready for action and that is about
everything I need to tell you about the function of this gun. It just turns off automatically after
30 seconds so there's no specific on and off button and really there's nothing else to talk
about other than let's shoot a few nails and I'll show you how it performs. This nailer bear without
any batteries is currently retailing on Amazon for £160. You can also buy it in B&Q for a little bit
more or on the Ryobi website itself for a lot more. It's over £200 on the Ryobi website so
if you're interested in buying one of these definitely go to Amazon. I'll put an Amazon link
in the description below. The one thing I found it doesn't do is it doesn't leave a mark other than
for the nail because it's got this little rubberized tip here that actually protects the
wood and now if that wears out or you do lose it what's the little nice feature is that they've
actually supplied you with a second one that sits on the back there. One thing I do like about this
is the way that you can actually put it down and it doesn't fall over. What you can't do is
actually balance it on the battery. It's a little bit front heavy to sit on the battery. The other
thing the magazine has got is it's got a couple of slots here that tells you when you're starting
to run low on nails so I've only got a few left in here. Let's see if I can demonstrate what I mean.
You can start seeing that yellow section come through that window there and that tells you
you're about to run out of nails. Okay which I have. Once you're down to only a couple of nails
it won't let you fire any more until you put some more in. Like all of these cool disnailers this
version is reasonably heavy at just under two and a half kilograms and that's without the battery so
it does make it quite a heavy machine when you're using it for a prolonged period. So that's a little
bit of a negative point because it is quite bulky and quite heavy. I'm not saying it's any worse than
the other ones on the market but to lug something this around like this all day is quite chunky.
The only thing I can compare it with is my shop air nailer which is obviously run off of a
compressor. Now the great thing about this is how light it is. There's hardly anything to it
and it's so it must be maybe a quarter of the weight and it just works really well. I mean this
is cheap other than the fact that you do need a compressor. However I suppose one of the drawbacks
is this. Now obviously if you're working in a workshop and you can set this up and you're just
working in one place I would say that this is more convenient. It's lighter you just put it on the
bench and it's there when you want it. However that is I suppose the plus side of a gun like this
that it is so portable and you don't need any cables or wires or hoses or whatever. You can
just take it where you want which leads me on to what I've been doing with it for the last few
weeks. So let's have a look at some real world work rather than just shooting nails into the
workbench. Straight out the box I started making some boxes and some hangers for my French cleat
system which it performed okay on. I was changing nails nearly every few shots depending on the
thickness of the ply and the timber that I was using. So actually changing nails I think is
really really quick and just works really quite nicely. According to Ryobi this will shoot 1,950
millimeter long brad nails on a full charge of 5 amp hour battery which wouldn't surprise me at
all because I've not run out of battery while I've been using this at all and I've shot quite a few
hundred. Using it on the workbench like this it would have been just as easy to use my lightweight
air nailer. So this isn't really the environment where this nailer excels. What I have been using
this nailer on mostly is my walk-in wardrobe project and this is where it really excels. The
whole idea of not having a cable or a hose and being able to take it into any room in the house
and just use it at a moment's notice is what this nailer is really designed for. Just fixing things
like architrave or door stops is far more accurate with a nailer than by hand because you can
position the piece perfectly and then let the nail gun do the work rather than then trying to get a
nail and a hammer into it. This not only speeds up the operation but it actually means that you end up
with a better quality job and as this four amp hour battery just shoots literally thousands of nails
it's not like I'm thinking that I even need to take another battery with me. In an environment
like this as long as you've got a pocket full of nails then you're pretty much set for the whole
day and I think that's where this nailer excels and comes into its own compared to something that
obviously comes with a cable. It's so versatile when you get into tight spaces and you're moving
around and you're doing work around the house but actually you forget that it's over two and a
half kilograms in weight and you just use it. This is great to use in a workshop but this hose and
obviously the compressor that's on the other end really stops you using it around the house so this
is workshop only and that's where I think really this nailer comes in. It's great for your second
fix items so all your architraves and skirtings and your door stops and your bits and pieces.
To have this in your toolbox for those items I think is well I found it really useful and I must
say I've really appreciated having this over the last few weeks and it has sped up all those sort
of second fix items I've been trying to finish on the project upstairs which brings me on to
the question that I posed right at the beginning of this video which is should you go and invest
in your own cordless brad nailer? I would say as long as you've got more than let's say a door to
fix and you can afford it absolutely go and invest in one of these you'll use it far more
than you think it'll really speed up your work and you'll find that you'll get higher quality
and you'll get trimmed to fix better because you can actually hold it while this does the work
rather than trying to use a hammer and nail. Whether you should invest in the Ryobi or not
well all I can say is this has done everything that I've wanted it to do for me recently and it's
worked really well without any sort of hiccups so I would say this is quite a good machine however
you're going to need to wait until I do some comparisons from this on other budget machines
coming very soon. So I hope you enjoyed this video and it's helped you make your mind up
whether you should invest in a bit of a nail gun. I will see you next time.
