How to Replace Prius Rear Struts/Shocks - Gen 2 (2004-09)

Autos hacks
81 followers
2 Video Views·Aug 9, 2025
Thanks for coming back for more Pi, everyone.
Today I'm going to show you how to replace the rear struts on a Gen 2 Prius.
Or the shocks, depending on which model you have.
I decided to get the full assembly versions, that way I wouldn't have to compress the spring
and put them on the new ones.
This way I can just swap them out easy.
So let's get to it.
The top of the struts is hidden below the trim in the back of the car, so we're going
to have to remove a lot of it to get access.
I'm using a 10mm socket here.
Once you lift up the battery trim cover, take note if any clips broke or got stuck down
in the battery cover.
I'm using panel removers that I got from Harbor Freight.
It's a good idea to have extra Toyota trim connectors on hand in case you break or lose
any.
And remove the auxiliary battery cover, same on the other side.
This compartment has a 10mm plastic nut holding it down.
Just get that in there, and the whole thing comes out.
Go off the way of stripping.
Next thing is to loosen this panel here by the door.
Now we can begin removing the side trim panels that are covering the struts with a 10mm socket.
There we go.
Now there are four panel connectors to be removed.
That one broke, so I'll have to replace it.
The second two are at the rear.
And the fourth is up next to the seat.
Careful when moving this panel around though, because there's not much slack to the light
bulb.
Now on the right side, there's a vent that goes to the battery, but it's only held in
with a couple of panel connectors.
Now if you want, you can remove this metal plate to get a little more access to the strut.
But there's seven bolts to be removed, and two of them were even covered up by the seat,
so I had to take that off as well.
There we go.
There's the strut.
You'll still need an extension to get access to these nuts, but it won't need to be as
long now.
Now that we have easy access to the strut, it's time to jack up the car.
Let's pop on the parking brake.
Now some people recommend jacking up the axle before moving the strut, but I found this
to be counterproductive, because I ended up having to push the axle down to take the
strut off.
Now note that there is one 14mm bolt that you'll need to remove from the bottom here.
But from the top, you'll need to remove the two other smaller nuts.
This time they're 12mm.
With that metal plate gone, I was able to break this nut with just one basic extension.
On the other side, I left the metal plate on, but I was able to access them with two
extensions.
And remember, don't try to remove the third larger nut like I did.
It is welded to the frame of the car.
The penetrating oil I sprayed on helped a lot too.
Using a 19mm socket and some penetrating oil, I was able to get the last nut off the strut.
There we go.
There's a little washer.
Oh, it's like stuck on the axle.
If you want to support anything with a jack, I'd recommend it would be the new strut while
you screw it in.
I found it was a much better idea to support the new strut rather than the axle of the
car.
Don't fully tighten these nuts just yet.
Wait until you have the bottom of the strut connected first.
Now that those bolts are in like this, push it away, pull the axle down, and push it in
there.
I also put a little anti-seize on both sides of the washer.
Don't fully tighten this nut either.
Wait until the car is fully down first.
A wrench.
Again, this last bolt is 14mm.
Once all the bolts and nuts are in place, tighten them down to 59 foot-pounds.
On my torque wrench, that is just over 700 inches per pound.
Alright, pop pop.
Putting anti-seize on the drum brake is a good idea too.
It's tough to get underneath the lowered car, but when you do, you can finally tighten the
nut to 59 foot-pounds.
That's what I like to hear.
Once you have both sides done, you can start putting the inside of the car back together.
There.
Okay, good enough.
Then, make sure there's still tap connectors down here.
Jeez!
So that about sums it up.
I hope that this video was helpful for you guys, and I'll be making other tutorials as
my Prius needs repairs as it ages, so yeah, thanks for watching!
