In this video I’ll show you how to make a planted aquarium for a Betta fish! I’ll take you through the entire step by step process & give you plenty of tips and tricks along the way. I hope you enjoy the video and find it useful!
In this video I'll show you how to make a thriving planted aquarium for one of the
most beautiful creatures in the aquarium hobby. Obviously I'm talking about a Siamese fighting
fish more commonly known as a betta fish. Let's waste no time and get straight into the build.
I'll be using this rimless glass aquarium and I'll put all the measurements up on screen now.
The first thing that I want to do is make an adjustment to the glass tank.
I'm going to use a sheet of acrylic to create a separate compartment where the filtration will
take place. This will not only result in better filtration but it will also mean I can hide
equipment like the heater from the main part of the tank. I've taken some measurements of
the internal dimensions of the tank and now I'm cutting the acrylic down so it fits inside.
Ignore the grey colour as that's just the protective coating that I can peel off later.
Now it's time to attach the piece that will separate the filter media from the filter.
I'm using some sandpaper to scratch up the acrylic where I'm going to attach the barrier.
This will help the glue hold much better. With a line of super glue in place I can now carefully
place on the barrier. One thing to note is that they're going to be locked together in just a
second or two so make sure you take your time to get it in the right place before attaching it.
At the bottom I'm attaching this small piece of egg crate which will allow the water to
freely pass through whilst holding back the filter media. As I'm sure you can see I've
drilled out a square on the left which is where the water will flow in and the hole on the right
is where the water will be pushed back out by the pump. I've removed the protective coating
from the acrylic so it can now be installed inside the aquarium. I'm applying a bead of
silicone along the back and bottom before pressing it in place inside the tank. I'll use some more
silicone to seal up the edges before leaving it to dry for 24 hours. It's the next day and I think
it's turned out really well. Before moving on let me quickly explain how it works and why it's
beneficial. The water will overflow from the main part of the tank through this square and into this
first section. This is where all the mechanical and biological filtration will be and as you can
see there's a lot of space for it. The water will then flow through the egg crate at the bottom
into this section where a pump will push it back into the tank. Other equipment like a heater can
also be placed in this second section. This means that no equipment will be visible inside the tank
and I think that looks much more natural than having something like a filter or heater blocking
the view. Now let's move on to the lighting. The light for this build was kindly sent to me by
Chihiros. This is their C2 RGB LED light. There's a bracket that mounts it on the side of the tank
and that makes it super easy to raise or lower depending on your preference. The light intensity
and timer can all be controlled through an app which is always super handy. This tank's going to
sit on my desk where it's visible from the front and side angles so I need to take that into
account for the hardscape. I found this stunning piece of driftwood in my local fish shop and I
think it has the potential to look really good inside this scape. Just like always I'm taking
some time to experiment with multiple different layouts but this is slightly more difficult than
normal as I need to make it look good from not one but two sides. Some of the branches are pushing
right up on the glass so I'm breaking them off to give it a better fit. I quite like how it sits
here but it definitely needs to be elevated so let's add some substrate. For this aquarium I'm
going to use Tropica Aquasoil. I'm using my hand to slope the substrate up to the back right corner
as this is going to help create some depth. With that done I can place the driftwood back inside
and add even more detail with some rocks. These are serious stones. I think their light colour
will contrast the dark wood and substrate really well. I'm trying not to overdo it with the stones
as I want to leave plenty of room for the plants. I'm pouring in some more aquasoil towards the back
to build some more height followed by a few more stones to add some more detail. I'm really happy
with how the hardscape's looking so far but there's a few things that need to be done before I can
start planting. Once I fill the tank up with water the wood is definitely going to float which would
destroy all the hard work that I've put into it. An easy solution to this is to use the super glue
and tissue method to lock the wood to the rocks. All I'm doing is wedging in some tissue between
the serious stone and wood and then soaking it in some liquid type super glue. It dries really
quickly and it's 100% shrimp and fish safe. It's even strong enough to be pulled out as one entire
piece but I do like to add a few more contact points just to make sure that it holds up for
the long term. As this aquarium is for a better fish it's going to need a lid so these branches
at the top need to be trimmed down. I think the easiest way to do this is going to be completely
removing the hardscape and then using some pliers to break down the branches. By using pliers instead
of something like a saw it will create a more natural break instead of a clean cut. After a bit
of work all the branches are sitting just below the top of the tank which will allow a lid to sit
nicely on top. I'm adding some more aqua soil in the back to build some more height followed by
adding a few more serious stones for some more detail. I love how this hardscape's turned out
and I think it looks great from not only the front but also the side as well. Before adding any plants
I'm going to give the entire tank a really good spray down. I want a carpeting plant that stretches
all the way from the foreground in the front to the foreground in the side. I think a great plant
for this would be Monte Carlo. It's super easy to grow and will form a dense carpet in no time at
all. I've split a couple pots up into lots of smaller chunks and they can now be planted inside
the aquarium. I like to use the tweezers to plant them nice and deep inside the aqua soil as this
stops them from floating up once the tank's filled up. To add some nice variety to the small round
leaves of the Monte Carlo I'm going to plant in some of this Crypt Parva. It's leaves stay extremely
small and I think it'll add some nice detail at the base of the hardscape throughout the tank.
Sticking with crypts I've got another species that I think will look great inside this aquarium.
I've never used this one before so I'm excited to see how it looks after it starts to establish.
I've split it into two chunks planting the larger one on the right with a smaller one in this gap
behind the cereal stone. I'm going to go ahead and plant a few more species of crypts in the
Now let's move on to planting the background as it's looking quite empty.
This here is a species of Rotala that has some really nice fine detailed leaves. I've never
used this plant before so I'm not completely sure how it's going to grow so I guess I'll just have
to wait and find out. The stems should grow right to the surface of the water and get more colourful
as they do so. I'm liking the planting so far but there's definitely a few more species that I want
to add before filling the tank up with water. A light spray down every now and then helps keep
the plants nice and hydrated and stops them from drying out. This is trident fern and I think it
will look really good growing amongst the tall branches of the driftwood. It's an epithite so
I haven't got to plant it in the substrate and I can simply wedge it in gaps between the wood.
Next to go in is some Bucephalandra and Anubias. These are slow growing epithetic plants that
will add some really nice detail to the aquarium. I've cleaned off all the rock wall so they can now
be planted throughout the scape. In some areas there's no gaps that I can wedge them into so
I'm using a small amount of super glue to mount them in place. I'm mainly planting them around
the driftwood as that's where I think they look most natural. I'm really liking the planting so
far but I think it can look even better with a couple additions. I'll quickly show you how to
make these mossy stones that you can freely place throughout the scape. You'll need some small pieces
of rock, it doesn't matter what kind they are as they'll be covered up anyway. Some thread and then
some moss or liverwort that you want to use. I'm using Riccardia which is a species of liverwort.
I'm tying the thread around the rock and then placing some Riccardia on top. I can then wrap
the thread around to lock it down, tie it off and then cut off the excess. These mossy rocks are
really quite simple to make and in my opinion I prefer it to the glue. They're super easy to place
inside and you can even move them or take them out completely if you ever wanted to.
Before I can fill the tank up with water I need to get the filtration sorted.
As I mentioned at the start the water will flow through this first section down through the egg
crate into the second section where it'll be pushed back into the tank. In the first section
I'll start by adding some ceramic rings which will do the bulk of the work in terms of biological
filtration. On top of that I'm adding some filter foam followed by some fine filter floss which will
polish the water and keep it crystal clear. This is the pump that will push the water from the
second chamber back into the aquarium. It's a small USB pump that's even adjustable which is
always handy. I've built this output tube that attaches to the pump with some tubing and push
fittings. The end lines up perfectly with the hole that leads back into the tank. I've then created
this output nozzle from an acrylic drinking straw that goes into the push fitting. I created the
shape by heating it up and using the back of a sharpie to open up the end. I think this output
will work really well as it can easily be removed whenever I need to clean the pump.
Although it probably is a bit overkill I think this filtration system will work really well for
this tank. Now I think it's time to fill the aquarium up with water. The bubble wrap helps
disperse the water and stops it from disrupting the aquasoil which would likely uproot the plants.
The water is nothing special and it's just dechlorinated tap water.
Now that the tank is filled up I can turn on the pump and see how everything works.
Everything's working really well and the bonus of the overflow filtration is that it also skims
the surface and keeps it nice and clean. Before I can leave the tank to grow in I need to set
the light up properly. I'll have it on 50% power to start with and set the timer up so it's on for
six hours a day. I'll slowly increase the intensity week by week until it's close to 100%.
Doing this gradually helps reduce algae at the start. I'll place the CO2 diffuser in the back
part of the tank where the small bubbles can be sucked up by the filter and blown into the tank.
CO2 certainly isn't essential but it will help with the plant growth.
Now that the aquarium's all set up all that's left to do is to leave it to grow in and establish.
After four months of growth this aquarium is completely transformed and I'm really happy with
how it looks. With that said it hasn't been the smoothest journey and there has been a couple
battles with algae. It was mainly growing throughout the Monte Carlo carpet and on the
stems in the background. I'm glad to say it's mostly cleared up but there is a few patches
here and there if you look closely. At the moment the only inhabitants are a few Amano shrimp but I
really can't wait to introduce the betta fish. As you may have noticed I have added a white
background to the tank. I think it makes the green plants pop much better and I think it frames the
aquarium in really well. As for other changes I've added some small black strips to create a grid on
the overflow section to stop any creatures from being sucked in. The filter box is still working
great but I do need to make an addition. I'm adding a heater which will help keep the water
at a stable temperature of 24 degrees. This is a must if you plan on keeping a betta fish.
They're also known for jumping out of aquariums so I'm placing on a lid to ensure this never
happens. Each corner has a small pad of silicone which will help stop the glass from sliding around
on the top of the tank. I'll leave the tank for a day or so to get to the proper temperature before
introducing the betta fish. A few days have passed and the tank is now home to a stunning male
betta fish. I really love his blue coloration and I think it pops out against the green plants
really well. He's certainly not shy and loves to explore the tank and swim amongst the plants.
I'm definitely going to need help with a name so be sure to drop your suggestions in the comments
below. As I mentioned at the start this tank will be sitting on my desk so it's going to be great
to have some company whilst I'm editing videos. Despite the battles with algae I'm really happy
with how this tank's turned out and I think it looks really clean without any equipment visible
inside the tank. Once again be sure to drop your name suggestions in the comments below
and as always thank you for watching.