DIY Wind Turbine Science Project

Terrific Physics
39 followers
In this video, I'll show you how to make a wind turbine that you can use for a science project
using some easily available materials. See the link in the video description
for written instructions and a complete materials list.
Adult supervision is required for the first few steps.
Start by cutting the neck off the top of a 1 liter plastic bottle.
This will form your wind turbine's tower or foundation.
Next, use scissors to cut two pieces out of the sides at the top of the bottle as shown here.
This will allow you to attach a second smaller bottle as the nacelle,
the horizontal piece at the top of the tower that connects to the turbine blades.
Fill the tower base with marbles, rocks, or other heavy objects to add weight.
This will help prevent the tower from falling over when the wind blows on it.
Next, you need to drill one hole in the cap and one hole in the bottom of the smaller bottle.
Later, a drinking straw needs to be able to rotate freely in these holes,
so the holes should be a slightly larger diameter than the straws you will use.
A quarter inch drill bit is usually a good place to start.
If you have trouble getting a hole started, you can use a smaller drill bit or a drill
bit with a sharper point to drill a pilot hole and then resume drilling with the quarter inch drill bit.
Now it's time to prepare a set of blades for your wind turbine.
We'll show you how to make a single basic set in this video, but things like blades,
size, and shape are variables that you can change and test for a science project.
Start by measuring and cutting out two 8 by 10 centimeter rectangles of paper as shown here.
Then, without creasing them, fold each piece of paper in half and tape together the two longer
edges. This should form a teardrop shape when viewed from the side.
Now you'll start building the rotor for your wind turbine.
Pinch the end of one straw and firmly press it into the end of another straw.
This is a good point to check and make sure that the straws fit and can spin freely in the holes
that you drilled in the smaller plastic bottle earlier. If needed, use a bigger drill bit to
Take your two connected straws and mark a line 10 centimeters from each end.
Place a thin strip of glue going from one end of the straw up to the line.
Take one of your blades and hang it from the straw with the rounded edge facing up.
You need to wait for the glue to dry, so if you don't want to hold the straw the entire time,
you can place it on an elevated object and weigh it down or tape it there so the straw doesn't fall.
Repeat the process on the other side to attach the second blade.
While you're waiting for the glue to dry, take a paper clip and bend it so it is as straight as
possible. Then, using needle nose pliers if necessary, bend it into a T-shape as shown here.
Take your T-shaped paper clip and firmly tape it to the center of your double straw like this.
Take another straw, which will form one half of your wind turbine's axle.
Slide it over the paper clip and then firmly tape it to the double straw.
Now you need to curve your blades. Take one of the blades, wrap it tightly around the straw,
and hold it in place for one minute. After that, let it uncurl. Then, curl the other blade in the
opposite direction. Again, hold it in place for one minute and then let it uncurl. Take another
straw, which will form the other half of your axle. Cut a tiny slit in one end of the straw.
Straighten one end of a paper clip and place it into the straw so the paper clip can hang down
slightly into the slit. This will help hold the paper clip in place when the axle rotates. Then,
firmly tape the paper clip to the straw. Cut a piece of string that is slightly longer than
your tower is tall. Tie one end to the paper clip that's taped to the straw. Tie the other
end to another paper clip. Bend the end of that paper clip out slightly so you can use it as a
hook to hang weights. Now you have all the parts ready to assemble your wind turbine. Take the
straw with the paper clip attached, fold and pinch the other end, and hold it for one minute.
You want it to retain the pinched shape when you let go. Place the smaller bottle horizontally
into the top of the larger bottle. Take the two halves of your axle and thread them through the
holes at each end of the bottle. Carefully press the pinched end of one straw into the open end of
the other straw. Press firmly so the straws connect, but don't press too hard and bend them.
Spin the rotor by hand to make sure the entire assembly can spin freely.
If needed, you can tape the two bottles together to prevent them from wobbling.
Now you're ready to test your wind turbine. Try aiming a small tabletop fan at it and turning the
fan on to its lowest speed. If the turbine doesn't spin at all, you can try moving the fan closer
or using a higher speed. To reset the string, simply turn the fan off and unwind the axle by
hand. For a science project, you can hang weights like washers or other paper clips on the hook and
experiment to find out how much weight your wind turbine can lift at different fan speeds.
If you've taken a physics class, you can even calculate the power output of your wind turbine
by measuring the amount of time it takes to lift the weight. You can also experiment with different
blade designs, like blades that are different shapes or different sizes, and compare their
performance at a constant fan speed. Remember, you can find complete written instructions for
this project linked in the video description. To browse over a thousand other science projects
and find one that matches your personal interests, visit us online at www.sciencebuddies.org.
