Hand building a slab mug with texture tutorial

Ceramic Art Studio
35 followers
Jul 22, 2025
Hello, my name is Rana from Curly's Clay Creation and since I've been asked by many people to do a
slow version of my slab mugs, this is what I'm doing. So this is my first tutorial so bear with
me if I miss anything. I will talk you through a couple hints and secrets and if you have any
questions, comment them and if you like the video, share it. Thank you.
So I already rolled out my clay and I've compressed it.
I use baking silicone sheets for patterns. I actually have drawers and drawers of different
forms of patterns. Have it be doilies, silicone, things I find at thrift stores,
at flea markets. So all I do is look for any form of texture nowadays. So
this is the one I'm using today, the one that I posted yesterday. I believe I bought this one
on Amazon. So what I do is I place it down on the clay firmly so that it doesn't move when I roll it.
I usually impress the corner pieces for the bottoms even if they're a little narrower.
I usually use cooking spray on my cookie cutters to avoid sticking
the bottoms. Make sure it's bright enough for you. All right. Luckily the mat that I use is
pretty much the same measurement as the mugs that I usually do. I make my own templates using
folder dividers because they are see-through and I can sort of see the pattern. If I want to cut
the sides of the mug and I need to center it with the pattern, I'd be able to see it. So
these are perfect. And I'm going to be making this size today which corresponds with the cookie
cutter that I just cut the bottoms with. So since these are perfect, I don't have to measure
later. Now this comes handy so I can cut the edges. And when cutting the edges, make sure you
slant your knife in the same directions on both sides so it has a clean seam once you start
building. So as you see, I'm angling the knife down to the right and cutting on one end.
And keep the knife angled in the same direction and cut the opposite end.
And do the same to the other one. So I like to get other things done and let these sit for a
minute just to sort of stiffen up a tiny bit to be easier to work with. So while I wait for that,
I score my bottoms. A lot of people thought my mugs that I posted yesterday were bottomless
because it was so fast. But I swear they have bottoms. So I score the bottoms.
And while I'm waiting, I might as well make my handles. And I'll show you my trick to doing
handles. I like to keep my table moist when I do this so that my handles don't crack from dryness.
Rolling out coils.
So
I've been doing this a minute so I know typically how thick I want my coil. So every mug is different.
Okay, so what I do is I bring back my mat and I lay my coil across it.
And I ever so gently just roll it with a rolling pin to flatten it out a bit.
And that way I have pattern on my handles. I know the video is not too bright so
better luck next time I guess. And with this size mug I usually cut a six and a half inch
handle which works out good for them. So I'll cut the ends off and go six and a half inches.
And what I do is usually cut a slant on the top part of the handle and then cut the slant
on the bottom part of the handle and fake shape it. There you go. Just to save time,
I'm going to go ahead and score these for later. Okay, the ends that you cut slanted,
go ahead and score. I'll score this one too. And apply a little bit of slip. Some people use
water. Some people use watery slip. I just put a tiny bit of slip on the edge of that.
I'm really handling this gently. Although it seems like I'm going a little rough,
it's pretty gentle. And I make sure the seams are aligned and give it a tiny bit
of pressure to seal it. As you can see, there you go. Not much of a mess. Not much of a smudge.
And the inside is where I'm going to be, let's see, smoothing out the seam. To smooth out the
seam, usually I like a little bit more water. So I just spray the inside slightly and I use my rib.
Now my seam is hidden. No more seam. There you go. That's where the seam is.
And if you want to work quick, you can just go ahead and score the top as you finish.
smooth the seam at the bottom just barely, which is fine if it comes out a little bit messy because
I still clean up my mugs once they're leather hard. Easier to handle when they're a little
leather hard. So there's the base of the mug and the walls. And I usually attach the handles right
at the seam to sort of avoid too much attention to the seam. And go ahead and score. And you can
wait until this is leather hard. I've never really had a problem attaching everything immediately.
I keep an eye on them. I adjust them as they dry. And since my handles are already scored,
all I do is hold the inside of the mug as I press firmly, softly but firmly,
to attach the handles. Attach the top one first and I make sure I support it from the back.
And then attach the bottom. And then typically to hold the round shape I use a red solo cup.
So I literally just gently align that. And it's good because it sort of narrows so
it'll fit perfectly any mug you make. So I just align it and I let it sit to dry shortly.
And there you go. A finished mug. Handles can be adjusted to how you like.
They usually hold their shape pretty good. There you go. And there you have it. A slab built mug.
