Keep Cows Out Of Hay Ring ~ SAVE MONEY

Family farm
230 followers
#FamilyFarm, #FarmLife, #SustainableFarming, #OrganicFarm, #FarmFresh, #HomesteadLife, #RuralLiving, #FarmFamily, #SmallFarm, #CountryLife, #BackyardFarm, #FarmToTable, #FarmAnimals, #SelfSufficientLiving, #FamilyHomestead
I think we may have solved the problem.
We tried to, we were trying to keep the cows
out of the hay ring.
They get in there, they do their business in there,
they ruin the hay, so you get down about 25%
and it's just all wet and yucky and poopy
and you name it, it's in there, they sleep in it.
We tried these here, we tried putting wood up,
if you can see right there,
and we've tried zip tying these on,
we have tried wiring them on, and as you can see,
there's one here, they rip them right out.
They'll just keep hitting them with their head
until they knock them off.
Cows are pretty smart, so we think that we found
the solution through our Farmers Co-op Century
that makes these rings, and these rings are awesome,
by the way, really great.
But, if you have calves or smaller cows,
you can see how large this opening is,
and look what they did over here.
We just put this bale in two days ago,
and this is what they've done to it
because they're trying to work from one side,
so later today or tonight, they'll be sleeping right here,
in here, there's Marigold, very interested in our tools.
We found what they call Bark It.
This is the Bark It right here.
They sell you 12 of these,
and all the nuts, bolts, and washers to put them on.
All you have to do is bolt these on the inside like this,
so there'll be two, there'll be two on each side like this.
We have to measure this out.
We're gonna measure them equally
so there's equal size holes.
So, I don't think that they'll be getting through that hole.
We got this fairly low cost at our Farmers Co-op,
they do sell them at Tractor Supply.
We got it for about half the cost,
so check with your Farmers Co-op if you're gonna buy this.
So, we're measuring this out, about 48 inches.
So, we measured these out, these are about 48 inches.
So, you divide that by three, I know that sounds weird.
I always have trouble figuring this out,
but you're gonna actually have three holes,
two bars is gonna make one, two, three openings.
So, you need to know what size each opening's gonna be.
So, you'd take 48, divide it by three.
So, we're gonna put a bar at 16 inches, 16 inches,
and it should leave about a 16 inch slot in the middle.
We're gonna measure 16 inches from each bar right here,
and Marigold's eating, so my measurements
are gonna change as we go here, I guess.
This is how I'm gonna line up my bottom.
I'm just gonna put the top one on, like this,
and we're just gonna line up the bottom.
One down, 11 to go.
We had to figure this out a little bit,
because you drill a straight hole through these,
it doesn't work, so we had to open up our holes
a little bit to get it to fit.
So, I think as we get going on this,
it'll probably get easier and easier as we go around.
One thing that I see that would make it a whole lot easier
is if you had a drill bit that could go through
both pipes at the same time,
because that's what's happening with ours.
I don't have a drill bit long enough
to go through both of them, so we're running into a problem
where we can't get the bottom on,
because the bolt doesn't go through all the way,
so we have to open up the holes on the bottom.
It's finished.
Turned out really good.
These were actually pretty tough
to try and line up the holes.
My recommendation, again, if you can get a drill bit
that will go through both of these,
it'll really help you out.
I could only go through one
and partially through another one,
but what I did find out is if you have
a regular-sized drill bit, do the bottom first.
Do the hole first, take your bar off,
finish your hole, bolt it on,
drill your hole up here, and then you can look down through
and see where to drill your last hole.
Thanks, y'all, for watching.
Make sure you subscribe for more videos like this.
Share it out with your friends, like it,
comment, and let us know how you like our new A-ring.
Bye-bye.
