雷克斯講航空歷史 霍克飛機公司(Hawker Aircraft)的早期系列飛機發展簡史
王者风范
22粉絲
208 次觀看·2025年10月30日
今天我們要來看看
Hawker航空公司最早的航空母艦
這是新系列的第一部
會探討最先進的航空設計
對於大多數的航空廠商而言
由於這些早期的航空例子
經常有很簡短或複雜的歷史
我認為是最適合在一個更長的短片中
而不是探討五或六個非常短的
Hawker
這家公司出生於不確定和惡劣的時代
直到第一次世界大戰結束
在這段期間
政府對於航空的政策
尤其是軍事航空
幾乎是不存在的
Sopwith
這家公司最大的名字之一
曾經試圖擴大和生產航空
為商業和軍事使用
然而他們在這個新領域的行動
最後失敗
他們必須回歸
製造汽車和摩托車
這家公司為此努力了一段時間
直到1920年
剩餘的軍事利益財政公司
發起了對於Sopwith的訴求
他們無法預期的付出
這家公司被放進了接收艇
最後被消滅
但從Sopwith航空公司的垃圾中
出現了一家新公司叫HG Hawker Engineering
這家新公司是由
pioneering Australian aviator Harry Hawker
who was also Sopwith's chief test pilot
and Thomas Sopwith himself
Hawker Engineering advertised itself
as a company that manufactured bicycles
internal combustion engines
cars, motorbikes and aircraft
but considering the names of its founding directors
it took little imagination for anyone to guess
where their ambitions lay
it therefore came as no surprise
when contracts were immediately accepted by Hawker
to recondition large numbers of war surplus aircraft
this was a valuable source of early financial stability
but Sopwith and Hawker were keen to design
and build their own aircraft as well
unfortunately
Hawker would never live to see this happen
on the 12th of July 1921
while piloting a Newport Goshawk
he suffered a fatal hemorrhage
as a result of spinal tuberculosis
Hawker was dead before his plane hit the ground
but his name would be immortalised
by the fledgling business he'd helped start
and Hawker Engineering's first aircraft
was just around the corner
By the time of Hawker's death
the design office was already filling with draftsmen
and while the government continued
with its short-sighted policy
of making do with surplus planes
the faint rustlings of specification papers
could be heard in Whitehall
as the true inadequacies of the RAF's equipment
became apparent to those who were farsighted
This soon resulted in the specification
that led to the Hawker Dyker
Though not the first plane designed
at the new company
it was the first to be built
but unfortunately it was not a success
Specification 7-22 outlined the general requirements
for an aircraft that could provide
gunnery spotting, reconnaissance
and unit liaison duties
This specification was a modified version
of one that had already been issued
but it had received universal complaints
from manufacturers
for having contradictory requirements
And this may have contributed
to all of the aircraft designs being submitted
being, well, rubbish
The design, tended by Hawker design staff
under newly appointed chief designer
Captain B. Thompson
was accepted
and construction began on a number of prototypes
The Dyker was of all-wood construction
though it was unusual for the time
in being a monoplane
as the British bias towards biplane designs
was still considered substantial
The parasol monoplane wing
was swept back
and braced by a pair of struts
on each side that connected to the fuselage
The wing itself was relatively thin
and the trailing edge above the cockpit
was cut away
to provide the pilot and observer
with a good view in all directions
The undercarriage was another unusual feature
It had a very wide track
There was no axle connecting the wheels
and the wheels themselves
were of a small diameter
Only one Dyker was completed
and that was only after
numerous alterations had been made
to the basic configuration of the aircraft
and it was flown a number of times
at Brooklands
during the summer of 1923
Initially, it was fitted
with an Armstrong Siddeley Jaguar engine
but this was swapped out
for a 430 horsepower Bristol Jupiter IV
before its first flight
In terms of armament
it was to have one Vickers gun
on the nose cowling
and provision was made
for a rear-facing Lewis gun
However, both of these were removed
owing to weight restrictions
Apart from the gun fitted on the nose
Vickers also produced
a large number of the equipment and parts
that were used on the Dyker
The wind-driven generator was Vickers
as was the undercarriage
flight stick, rudder controls
rear gun mount and tail skid
Had they been even more involved
it may have been cheaper for Hawker
to simply hand the airframe over to Vickers
After its initial flights
the plane went to Martlesham Heath
for official evaluations in late 1923
But after just 18 hours of flight time
it was clear that the Dyker
was not suitable as a military aircraft
Apart from displaying
severe aileron flutter
which resulted in the frightful tendency
for the wing to part company
with the rear cabane struts
the aircraft was directionally unstable
throughout its entire speed range
and it was subsequently rejected
The Dyker was then delivered
to the Royal Aircraft Establishment at Farnborough
for further evaluation
But no record seems to exist of these results
and the aircraft was likely scrapped
at the end of 1924
As a result of its poor performance
the other prototypes were not completed
and the only other model
that had begun construction
was reportedly taken out of the shed
and buried in a corner at Brooklands
Next up is the
Hawker Woodcock
This was designed to meet
specification 25-22
which called for a single seat
knights fighter
Initially the work of a team once led
by Captain Thompson
the first prototype Woodcock
bore many signs of its Sopwith heritage
featuring two bay wings
and being powered by an Armstrong Siddeley Jaguar
In March 1923
it made its maiden flight
in the hands of test pilot
F.P. Raynham
But it proved to not only be disappointing
but dangerous to fly
Aside from displaying an alarming amount
of wing flutter, even for those days
its rudder proved to be almost
entirely ineffective
And for this reason
spin recovery tests were never permitted
with the first model
When it arrived at Martlesham Heath
for service evaluation
it was rejected on account of its poor maneuverability
However, it did receive praise
for its reasonable field of view
and being simple to maintain
At this point, Captain Thompson
was replaced as chief designer by W.G. Carter
who would go on to be the lead designer
of the Gloster Meteor
and he immediately began to redesign
the Woodcock, replacing the Jaguar
engine with a Bristol Jupiter IV
and incorporating single bay wings
This new prototype
dubbed the Woodcock Mark II
was built with these new features
and flown for the first time
in August of 1923
It immediately showed itself to be an improvement
on the first model
The wing flutter, though still present
on some occasion, was considerably reduced
And positive directional control
was now achievable throughout
most of the speed range
Unfortunately, the Jupiter IV engine
presented an issue
with the exposed valve gear
being particularly vulnerable to icing up
It was also a problem that was experienced
to some extent by some other
uncoiled radial engines
As a result of this, the prototype
appeared at the 1924 Hendon display
with a series of individual
cylinder covers, each equipped
with manually operated shutters
to regulate the airflow
Soon after this, however, minor modifications
were made to the valve gear
and the fitting of an exhaust collecting shroud
in front of the cylinders
reduced the risk of icing and the cylinder covers
were removed
Following this, further
assessment of the Woodcock was conducted
towards the end of 1924
And after the tail surfaces
had yet again been improved, the RAF
deemed it acceptable for service
and placed a contract for the production
of ten aircraft
The first six of these, not fitted
initially with night-flying equipment
were issued to Martelstrom Heath
for further tests, and some then
served with No. 17 Fighter Squadron
after this
However, it was No. 3
Squadron at Uphaven that received
the first of the production Woodcock Mark IIs
Eight were delivered
in May of 1925
and these replaced their aging collection
of Sopwith Snipes
In total, 61 production models
of the Mark II would be built
most of which went on to serve as night fighters
with No. 3 and No. 17
Squadron
One of the aircraft scheduled for delivery to the RAF
was purchased by Hawker Engineering
as a demonstration aircraft
and entered by Tom Sopwith
in the King's Cup race of July 1925
Flown by another
Hawker test pilot, George Bulman
it was unfortunately
forced down at Luton by bad weather
in the opening stages of the race
and it was badly damaged
Nevertheless, its demonstration
prior to the race gave Hawker
some much-needed public exposure
In service, the aircraft was armed
with two .303 calibre
Vickers machine guns
These were mounted on each side of the fuselage
and were synchronised with the two-blade propeller
In the early days of their service
the Woodcocks suffered
a number of incidents that did little
to endear them to their pilots
The most serious of these issues
resulted from failures of the main wing spars
and there were several cases
of the undercarriage struts collapsing
though this was mostly attributed
to the poor surface of the airfield
they were landing at
W.G. Carter quickly put
the Woodcock through a modification program
and by the end of 1925
the structural weaknesses
of the aircraft had been cured
and the Woodcock became well-liked
as a night fighter
Only two squadrons would operate the Woodcock
flying night patrols over the Midlands
throughout the mid-to-late 1920s
However, with a maximum speed
of 143 miles an hour
and a simple twin-gun arrangement
it presented no significant
advancement over the Sopwith Snipes
it replaced. On the other hand
its acceptance by the RAF
enabled the small Hawker company
to survive in a time of much reduced
manufacturing contracts
After the Hawker Woodcock
came the Hawker Cygnet
which is unique for being the only
light aircraft developed by Hawker
The significance of this aircraft
lay in two things
Its remarkable design characteristics
and its designer
In 1923
Hawker Engineering employed the services
of a young draftsman who had
considerable experience in the design
and construction of wooden aircraft
His name was Sidney Cam
and he would go on to become
one of the most famous and influential
designers in British aviation
In early 1924
those years were still ahead of him
and his first job was to take over
the design of a light aircraft
One that was to compete in the
Light Airplane Competition
held by the Royal Aero Club
This event was backed by the Air Ministry
who provided funding for 3,000 pounds
in prizes
During such times of austerity
when every shilling counted
the competition would receive submissions
from companies great and small
including Hawker
Initially it was Wilfred G. Carter
who was in charge of the design work
for the Cygnet
But he handed the project over to Sidney Cam
reportedly saying that he simply
couldn't get used to thinking in terms of ounces
instead of pounds
Cam, however, could think in terms
of ounces instead of pounds
and when it was entered, the Cygnet
was the lightest aircraft in the contest
coming in at a featherweight
373 pounds
The airframe, weighing no more
than 270 pounds
was of all wood construction
and fabric covered
The fuselage consisted of four spruce lingerons
and braced in the form of a Warren truss
by diagonal cross sections
The wings were built upon
fabric-wrapped box bars
with Warren truss spruce ribs
and though the top center wing section
was attached to the fuselage
by four spruce-fed steel struts
metal fittings were kept to the absolute minimum
to save weight
Two Cygnets were entered into the competition
registered as
GEBMB and
GEBJH
The former was powered
by a 34hp
two-cylinder Anzani engine
and the latter by a 34hp
two-cylinder ABC Scorpion
Both survived the elimination
heats and gained fourth and third
places respectively in the final
The Cygnet registered BMB
won first place in the trials
for best take-off and pull-up
It also won the short landing
competition and
had some poorly timed valve trouble
not got in the way on the final day
would have certainly taken home
the Air Ministry's grand prize
The next year, both Cygnets attended
the 1926 LIM competition
These were now fitted
with the 34hp Bristol Cherub engine
Bullman once again
flew the Cygnet BMG
and BJH was flown by
one Flying Officer Rag
Rag won the LIM open handicap race
with Bullman coming sixth
but it was Bullman who finally won
the principal competition
on the 26th of September
taking home the Daily Mail prize
of 3,000 pounds
with Rag coming second
for a one-two finish
for the Hawker Cygnets
At the end of the 1920s
Bullman's Cygnet was put into storage
and mostly forgotten
However, after the Second World War
it was painstakingly rebuilt by Hawker
Over the years, it attended
numerous meetings, sometimes even
appearing at garden parties
and since the 1970s, it has been
on almost permanent display
with its current home being
the RAF Museum at Cosford
Before the Cygnet had competed
in its first race, development work
had begun on the Hawker Hedgehog
This was designed to
Air Ministry specification 37-22
which called for
a new carrier-based reconnaissance
aircraft to replace the Avro Bison
and the imaginatively
named Blackburn Blackburn
First appearing on the drawing board
as the Hawker T2, the Hedgehog
was designed as a three-seat
single-bay unstaggered biplane
It was of conventional
fabric-covered wooden construction
and designed to operate
the pilot, observer and gunner
in separate tandem cockpits
The pilot sat well forward
under the top wing centre section
but the gunner at the rear was just
clear of the wing trailing edge
of which a section was cut away
to improve their field of view
Powered by a 398-horsepower
Bristol Jupiter IV
the Hedgehog employed
some novel features for its day
These included the use of landing flaps
on both the upper and lower wings
Both wings also featured
so-called drooping ailerons
and the wings could be
folded for easier storage
and for carrier operations
The Hedgehog made its first flight
at Brooklands in February 1924
with FP Raynham at the controls
Upon completing
its initial test flights
it was then sent to Martlesham Heath
for the customary service evaluation
Here several officers flew
the aircraft extensively
and the Hedgehog's handling characteristics
were met with universal approval
Its stalling characteristics
were especially praised
as was its ability to recover
from said stalls
However, by the time
the Hedgehog had completed these trials
the Air Ministry cancelled
the requirement for it
In their eyes, the Hedgehog's performance
though good, did not present
sufficient advancement over the existing
Avro and Blackburn models
neither of which had yet to complete
their first year of service
Nevertheless, the Air Ministry purchased
the sole example of the Hedgehog
and it was returned to Martlesham
as an experimental aircraft
There, further tests
were conducted on the unusual
drooping ailerons during the first half
of 1925
After this, it attended the
RAF display at Hendon
before being converted to a float plane
and tested by the Marine Aircraft
Experimental Establishment
who tested it over the summer
Once converted back to a land plane
it saw some use in deck handling
trials aboard HMS Argus
in September of 1925
The following year
it was fitted with a new 450hp
Jupiter 6 engine
and despite being the only
model, it was redesignated
as the Hedgehog Mark II
After this, its fate becomes
obscure, but it appears
that the aircraft was written off
sometime during or just
after 1927
when it nosed over in a landing incident
The Hawker Hornbill
in a return to avian
nomenclature was
W.G. Carter's answer to Air Ministry's
specification 7-24
This called for a
high-power, single-seat fighter
It was to be powered by the
new, boosted, ungeared
Rolls-Royce Condor 3 engine
It was to have a top speed
of no less than 208 mph
and it was to have a service ceiling
of 29,000 feet
This specification was an attempt
by the Air Ministry to break away
from traditional radial engines
a heretical concept to some of the old guard
and explore the possibility
of acquiring a fighter aircraft
with significantly advanced performance
Recognizing this, Carter
paid particular attention to the
design of the closed cowling of the engine
The result was a small
and exceptionally sleek biplane
for its time. The Hornbill was built
as a single-bay biplane
of mixed wood and metal construction
The engine supports being made of
steel tubes, with the whole
arrangement snugly clad in
duraluminium panelling. For cooling,
the aircraft had two radiators
mounted under the lower wing
and although it was meant to have a
spinner over the propeller, this was
not initially fitted so that a
HUX starter could be used for the engine
The Hornbill took off for the first time
in July of 1925
It was flown by Raynham
on its first flights, however
George Bullman would soon join
as the chief test pilot
After the initial flights, which
resulted in the fitting of a metal
propeller to try and improve performance
the aircraft was taken to Martle
Trimheath for assessment in December
During the course of the evaluations
it was found that, despite
having a very snug cowling
the Hornbill was no
match for the depressing climate of a
British winter, and its engine
suffered repeatedly from the problem of
overcooling. Attempts were
made to combat this, mostly
by covering up most of the outer
segments of the radiators, but
eventually the decision was made to take
the Hornbill back to the workshop for
extensive modifications. All
of the modification work was done under
the supervision of Sidney Cam, who
by now had taken over from Carter
The engine was replaced
with the new Condor 4, which
produced 698 horsepower
and its longer crankcase
required new covering panels
which were raked back and flared
flat across the top of the engine
The two radiators were sensibly replaced
by a single circ radiator
that was mounted between the landing
gear struts, and the tail
fin and rudder were both slightly altered
to increase their area
After these modifications were complete
the Hornbill returned to Brooklands Field
and Bollman completed a series
of performance and handling flights
Though the Hornbill was designed
to carry a Vickers gun, it
was not fitted because the Condor
engine had not been installed with a
synchronization gear, and for these
flights, ballast was used to simulate
the weight of the missing gun
Its low-speed handling surprised
Bollman, who found the aircraft easier
to control at speeds that would induce
a stall for most others
But overall, he was
unimpressed. It had numerous
faults, one of the biggest being
a dramatic loss of engine power
above 16,000 feet
After a brief appearance
at the RAF display at Hendon,
the Hornbill returned to Martlesham Heath
for its full service evaluation
as well as a comparative evaluation
against the Armstrong-Whitworth
Siskin III
Though the Hornbill was considerably
faster than the Siskin at altitudes
below 20,000 feet,
its low ceiling killed
any hopes for it to be considered
as a service aircraft. On top of this
was the litany of complaints
that came from Bollman after his
test flights. The engine was
now overheating, a result
of normal service fuel being
unsuitable for the Condor when flown
at full power. Despite
strengthening, the aircraft tended to break
its stern post upon landing
Directional stability and control
were lacking at higher speeds,
to such an extent that even full rudder
was barely enough to maintain height
in steep turns at speeds above 150
mph. But worst of all,
Bollman said that the cockpit was
so cramped that it was impossible to
reach the cocking handle of the Vickers
machine gun, and that a larger
than average pilot would find it impossible
to safely bail out in an emergency.
To quote Bollman himself,
he said the Hornbill was
too clever by half, and
the designer almost forgot that the
pilot is an important part of the
design. Despite its shortcomings,
the Air Ministry suggested
that the Hornbill be transferred to
the Royal Aircraft Establishment for testing,
as, even though it was
unsuitable as a service plane, it
displayed outstanding handling characteristics
at low speeds, and was still
considered an advanced fighter design.
Next up is the
Hawker Heron. This was
a relatively short-lived, but
important project that evolved
from the development of the Woodcock.
The Heron started life as
the third Woodcock that was to be built,
but Sopwith had obtained
the Air Ministry's permission to complete it
as a so-called Metal Woodcock
in early 1924.
The redesign work was given to
Sydney Chem, who quickly realised
that a completely different aircraft
would result from this work, and so
it was given the new name of Heron.
The structure was built
using steel and aluminium tubes.
These were attached
to form a rectangular section that was
then used with others to form a simple
box that was cross-braced with tension
wires. The parallel cord
wing had twin spars that were built
from light steel tubing, and the nose
of the fuselage behind the engine was covered
with duraluminium sheet.
Unlike the Woodcock II, the Heron
had straight wings of unequal span
and increased stagger.
A smooth contoured fin and horn
balanced rudder replaced the Woodcock's
original tail surfaces, and
completed the transformation of the Woodcock
into the Heron.
It first flew in mid-1925,
powered by a Jupiter-6 engine
that drove a two-blade wood propeller.
Although the Heron's weight
was a little more than the Woodcock II,
it managed to achieve a top speed
over 15 miles an hour faster
than its predecessor,
achieving 156 miles an hour
at 9,800 feet.
After this, it went to
Martosham Heath in December for its
evaluation trials. However, for these,
its wood propeller was replaced
by a Ferry-Reed all-metal propeller,
though in the end,
this made little or no impact
on its overall performance.
The Heron remained at Martosham
for most of 1927,
being transferred to No. 22 Squadron
for handling and performance reports.
During this time, it earned
a good reputation amongst pilots,
with considerable praise given
to its handling characteristics
and ease of servicing,
courtesy of the metal airframe.
After its time at Martosham was done,
the Heron was struck off
air ministry charge in May of 1928.
It then returned to Brooklands,
where, with its armament removed,
it was re-registered
and entered into the King's Cup race
at Hendon. Unhappily,
while being taxied to the start line,
it struck a parked car
and was badly damaged.
By the time it was repaired,
the certificate of airworthiness
had expired, and the plane was finally
struck off the register for good.
Sidney Cam would later refer
to the Heron with considerable affection,
suggesting that, for him at least,
it marked the transition
from the outdated fighter formula
of the Snipe, Woodcock and Grebe,
and the wing and tail layout
of the Heron can easily be recognised
in the later Hawker Fury
when it made its debut.
The next aircraft is the Hawker Horsley.
This has the distinction
of being the last all-wood design
drawn up by the company,
though many models
would eventually be completed
with either a mixed or all-metal structure.
It was also the first Hawker aircraft
to reach a production run
that exceeded 100 units,
with 124 Horsleys being built in total.
The Horsley was designed
as a two-seat, single-engine
medium bomber in response
to specification 26-23.
Construction of the first
prototype began in 1924.
However, its first flight
was delayed until the following spring
after a construction accident
caused significant damage.
At this stage, it was powered
by a Rolls-Royce Condor III
and featured two radiators
on the sides of the fuselage,
set back behind the engine,
like originally found on the Hawker Hornbill.
In May 1925,
the Horsley prototype was taken
to Martlesham for assessment
against the competing aircraft
by Bristol, Hanley Page and Westland.
Initial favour leaned
towards the Horsley,
especially as it was the only plane
capable of meeting the initial load requirements,
a point of some embarrassment
for the other competitors.
But the final judgement was withheld
as there were numerous complaints
about the Air Ministry's specification.
Specifications 23-25
and 24-25
rectified this issue,
with the latter also setting out load requirements
for both conventional and torpedo bombing.
Following complaints about
engine accessibility and ground handling,
the prototype Horsley had gone back
for modifications,
and during this time,
work had also begun on a second prototype.
The second prototype incorporated metal
in parts of the wing and fuselage structure,
and this aircraft was flown
for the first time on 6 December 1925.
When they returned
to Martlesham for evaluation,
both Horsleys were praised
for the ease in which they could be adapted
to carry various loads,
and this prompted the Air Ministry
to place a production order
for 30 Horsleys in March of 1926.
The first 10 of these
would be completed as the Mark 1,
which was predominantly of wood construction,
with the remaining being completed
as the Horsley Mark 2.
Number 11 Bomber Squadron
was the first to receive the Mark 2
in January of 1927,
which they used to replace
their ageing stock of fairy fawns.
Shortly after this,
Number 100 Squadron also replaced
its fawns with a new set of Horsleys,
and by 1928,
they also equipped Number 15
and 33 Squadron,
as well as the Anti-Aircraft Corporation
flight at Biggin Hill.
The Horsleys were a considerable advance
over the previous aircraft,
capable of carrying three times
the bomb load over greater distances.
The Mark 2 also featured
the improved Rolls-Royce Condor 3A,
as well as the new Mark 2B
bombsight.
Though in some photos,
usually without people as a reference,
the Horsley may look small,
it was actually quite a large aircraft.
The Mark 2 had a wingspan
just over 56 feet,
and it had a loaded weight of 9,200 pounds.
Its powerful engine
allowed it to carry some
impressive payloads for its day,
one being a 1,500 pound bomb,
though none had been produced
since 1918,
and the other being an 18-inch torpedo.
Speaking of torpedoes,
the prototype Horsley
torpedo bomber was built
from the 10th production unit
of the initial Mark 2 delivery order.
This aircraft was transferred
to the Torpedo Development Flight
at Gosport in early 1927,
where it remained for several months
before being shown to the public
at the Hendon Air Display in July.
At the end of that year,
an initial production order
for 12 torpedo bombers was placed,
with the first being delivered
in August of 1928.
These units went to the
Coast Defence Torpedo Flight in Scotland,
which was shortly renamed
to No. 36 Torpedo Bomber Squadron.
Subsequent orders were placed
for more torpedo bombers,
and these would be completed
with all-metal construction,
and were unofficially referred to
as the Horsley Mark 3.
Many of these served
with No. 36 Squadron
when it was redeployed to Singapore in 1930,
and they remained in service
until as late as 1935.
Horsleys continued to serve
home-based bomber squadrons
for several years,
participating in the yearly exercises,
and also appearing
at the Hendon Air Displays
from 1928 to 1931.
The arrival of the Vickers Wildebeest
in 1932 put an end
to the Horsleys' days as a front-line unit.
However, they would continue
to see extensive use for target training,
as well as some units
being used for all manners
of experimental testing.
From 1926 onwards,
various Horsleys would be used
as engine test beds.
The original prototype was used
to test a Rolls-Royce Eagle,
a Rolls-Royce H-10,
as well as the emerging Napier Lions.
Another was converted
to mount a Rolls-Royce Condor,
which was then featured at Hendon,
and other Horsleys were also used
to test the Armstrong Siddeley Leopard,
the Rolls-Royce Buzzard,
and even a Junkers Jumo
was installed on one particular model.
Perhaps the most significant
of all engines tested on the Horsley
was the Rolls-Royce PV-12.
Two aircraft would be used
to test this engine between 1934
and 1937,
gaining certifications
for various models of what would become
the Rolls-Royce Merlin.
The success of the experimental Horsleys
prompted overseas interest.
In 1929,
Hawker built six Horsleys
for the Hellenic Naval Air Service,
with five being delivered as military aircraft,
and the sixth to be used
as a VIP transport.
In 1930,
the Danish government placed an order
for two aircraft to be powered
by the Leopard engine.
This also included a request
to produce the aircraft under licence
should it prove satisfactory.
These two aircraft were completed
as the so-called Danetorp.
The design featured a mixed
construction of wood and metal,
the undercarriage could easily
be swapped out between landing wheels
and a pair of floats,
and the cockpit layout was changed
to facilitate a third crew member
between the pilot and the observer.
The first Danetorp was delivered
as a land plane, making its first flight
in September 1932,
and shortly after it was followed
by the second.
The latter also underwent trials
with floats at Felixstowe in November that year,
where, despite its larger size,
it performed well on the water.
Both Danetorps were flown extensively
between 1932 and 1933,
but despite performing well,
budget constraints
prevented the Danes from putting
the aircraft into production.
By this time,
the Horsley was already being phased
out of service at home,
and it would have probably been outdated
in its use within a few years anyway.
After the Horsley,
we have the Hawker Hawfinch.
Though ultimately unsuccessful,
it was the first all-metal design
built by Hawker,
and it was influential in the designs
of later fighters by both Hawker
and other manufacturers as well.
The Hawfinch was built to
specification F9-26,
which set out to
find a replacement for the Armstrong
Whitworth Siskin and the Gloucester Gamecock.
This requirement was
somewhat urgent,
as the Fairy Fox, a light bomber,
was about to enter service,
and rather embarrassingly,
it posted performance figures
that either matched or exceeded those
of the RAF's current inventory
of frontline fighters.
The Air Ministry was so eager to avoid
this scenario that they accepted
no less than nine different prototype proposals
from various manufacturers
over the course of 1926.
These included the
Bolton Paul Partridge,
the Gloucester SS-19,
the Bristol Bulldog,
the Armstrong Whitworth 16,
and of course, the Hawker Hawfinch.
Hawker was quick off the mark
with this one, being the first
to submit their design for consideration.
The Hawfinch prototype was built
as a metal structure to bay biplane,
with the wings arranged
with a considerable amount of stagger,
and it was to be equipped
with a pair of synchronized Vickers machine guns.
Per the specification,
it was powered by a radial engine,
this one being the Bristol Jupiter VI,
and it was expected to have a top speed
inexcess of 160 miles an hour.
Hawker was in fact
so quick in designing and building
the Hawfinch, it being flown
for the first time in March 1927,
that they were able to spare the time
to submit the aircraft for deck handling
trials aboard an aircraft carrier.
This it did aboard HMS Furious
in July.
These trials went surprisingly well
for an aircraft that had not been designed
with carriers in mind,
and the experience gained from these
allowed Sydney CAM to take an interest
in the new fleet fighter specification,
something that would eventually culminate
in the development of the Hawker Nimrod.
After the deck handling tests were complete,
the Hawfinch was prepared
for its evaluation trials,
and went to Martlesham Heath
in August of 1927.
Extensive trials of all the attending prototypes
were carried on until the early months
of the following year,
by which point the Bulldog and Hawfinch
were looking like the clear favourites.
Ultimately, it could not be decided
which of the two should be considered
for full-scale production,
as their performance figures
were exceptionally similar.
And so, the decision was made
to deliver both aircraft
for squadron trials.
These took place at Kenley,
Hornchurch, Northolt, Biggin Hill
and Uphaven.
Both of the aircraft were well-liked
by their pilots,
but in the end, the Bulldog
was judged the winner,
owing to its top speed of 174 mph
versus 171 for the Hawfinch.
The Hawfinch prototype
was then returned to the factory,
where single-bay wings
were temporarily introduced for testing,
and shortly afterwards,
the aircraft made a brief appearance
at Felixstowe to test the use
of a twin-float undercarriage.
From July 1929 onwards,
the Hawfinch was used by Hawker
and the RAE for trials
with heavily cambered airfoil sections.
It carried on in this manner,
being used for various experiments
for a number of years,
until some point in 1933,
when it was finally scrapped.
The last aircraft we're looking at today
is the Hawker Harrier,
and no, not the VTOL jet plane of fame,
but rather the first aircraft
to bear this name.
The Harrier was Hawker's response
to specification 23-25,
which called for a two-seat plane
capable of performing day bombing
and coastal reconnaissance duties.
This was based on
the failure of an earlier specification,
which had led to the Hawker Horsley,
as mentioned earlier on,
with the main failure being the lightness
of the required bomb load.
And so, before the Horsley
had completed its final evaluations,
design work on the Hawker Harrier
had begun.
It was designed with an all-metal structure,
and CAM made provisions for the possibility
of it having to carry a torpedo,
as it looked like the air ministry
were about to modify their specification
to include said requirement.
The engine chosen
was the reduction-geared Bristol Jupiter VIII,
but because of the gear's
relatively high power absorption,
the aircraft was somewhat underpowered
when it was completed.
The Harrier was flown for the first time
in early 1927.
It then performed its initial
flight trials at Brooklands
from March to November.
Thereafter, it was evaluated
at Mattersham Heath
during the winter of 1927-1928,
and again in the summer.
These initial trials
were carried out with a variety of bomb loads,
mostly the 112-pound
and 250-pound variants.
As predicted, the air ministry
then modified the specification
to include the requirements of carrying
the Admiralty Type VIII torpedo,
and the Harrier went back
for its already-planned modifications.
During this time,
the reduction gear of the engine was removed,
as during all flight trials,
a lack of power on take-off
had been the main complaint,
and the last thing a pilot wanted
when taking off from a carrier
over the North Sea carrying a heavy torpedo
was a lack of power.
Unfortunately, even with the new engine
now giving 583 horsepower,
the Harrier,
now carrying 3,000 pounds of torpedo
and associated equipment,
was still underpowered.
As a result of this,
its trials were conducted
with the rear gun mountings removed
and the fuel tanks half-filled
for the safety of the test pilot.
In one of the reports
received by Sydney CAM,
was a rare case of sarcasm
in the usually-stoic dictum
of the Martlesham Assessors.
In response to the required
weight-shedding for testing,
its quoted as saying,
It's a pity that it has been found
necessary to leave the observer
bomb-aimer on the ground
when bombs are being carried.
Unsurprisingly,
the Harrier failed to impress
and it was not selected for service.
In November 1929,
it was handed over to the
Bristol Engine Company
for use as a test bed.
It was first equipped
with a 495 Bristol Orion radial engine
and then the 870 horsepower
Bristol Hydra double octagon.
Here it lived out the rest of its days
before being struck off the register
and eventually scrapped in 1933.
Though it was a failure,
the Harrier served Hawker well
by aiding in the development of bombing
equipment that would later be used
in the Hawker HART,
and other smaller lessons were learned
that cumulatively aided the company
in future developments.
And so, that concludes our look
at the early aircraft designed
at Hawker Engineering.
As mentioned earlier,
I plan to do a few more of these
for some of the other manufacturers.
Not all manufacturers
require this sort of video,
but a lot of the ones that operated
in the 1910s and 1920s
had a lot of short-lived,
obscure designs that are often
better covered en masse.
So, I hope you all enjoyed this
longer video format for a change,
and as always, thank you all very much for watching,
and I'll catch you all next time. Goodbye.
