carved frame part two, wood carving

Hello friends, I continue to work on the frame. I made the lower and upper part of the frame. Today I will cut the sides of the frame. By the way, I will not remove everything, but only half of the side. They are all the same, mirrored. I will not describe how I make these curls, I will just shoot. I explained in the first video. I will dwell on these leaves in more detail. I pulled them out a little. Plus I added this element. It will be interesting to see how it cuts. I'm starting to work. I wish you a pleasant viewing. Immediately in the branches. I cut it. And I lower it down. After all this is lowered, I turn to this curl. The curl is ready. I turn to the leaf. Everywhere here. I cut in these places. There seems to be nothing complicated. In these places I will choose. Half-circular cutter. Slowly. A little. Carefully. So that nothing is chipped. And round off. All these elements. And this leaf, friends. I cut at an angle. Down here. By the way, it could be make a selection here. To diversify a little. This leaf. I cut it. A little to the other side. This leaf. Here a little. I lower. Down. Round off. This leaf is not very differs from this leaf. Here, of course, I added this element. And here it is not. So in these places I make a cut. As well as here. Half-circular cutter. In all places. And then I make a selection. After I finished with the selection I start these elements round off. By the way, in this thread it is not possible to cut one element without clinging to another element. For example, I need to lower here more, but this leaf already bothers me. Therefore, I must make a selection here. So that this element could be lowered below. So, I lowered it below. And now I can finish this one. And of course here I lower a little more. By layers it is already poorly cut. On the other side. The last leaf is left. I have already cut it from this side. So I take a corner and immediately separate this leaf from these two, from the curl of this leaf. I make such a small groove. So that I do not have to suffer with it in the future. So. Here is a selection. Here, here and here. By the way, I made a selection with a half-circular chisel. By the way, here you can round it. There will be no trouble. You can do it a little differently. But I decided so. It seemed to me that it was more suitable. Here I cut. And I start to choose. And here too I choose. I make a selection. Here I also make a selection. A small groove. It would be possible, of course, to cut it differently. Here to make a small selection. And here. I want to diversify it all. So that it is not similar. To be a little different. To look more interesting. And round a little. Here I make also such a groove. Small. At the same time I lower at the exit down. Pretty much down. I'll take a half-circle smaller. And here I round. At the same time, I round the end of the leaf. And I lower it down a little. And, of course, again I correct. Half-circle. I lower it down even more. Here, in my opinion, it is enough. Here, too, at the angle of this groove, I remove this groove a little. And, in principle, in this direction I will also remove the groove. By the way, against the wool I cut. At the end I have already begun to chisel. On the camera it is difficult to cut. Not always convenient. So, it turns out that these places should be at the same height so that they do not differ from each other. And this element I round. With this side I cut everything. It remains, of course, the back side of the cut. But I will choose a quarter. And I want to attach the panel to the frame. Or insert into the frame. And see how it looks. This is how it turns out. I chose a quarter from behind. I already tried on the panel. It looks pretty good here. I went around with a cutter. Here, probably, it will be necessary to go around with a chisel or a triangular cutter. I haven't thought about it yet. I'll come closer and then I'll decide. The back side of the cut remains. And, of course, grinding. My least favorite activity. But, nevertheless, it needs to be done. I will also do the panel in parallel. I will grind it. Fill in the background. Of course, I will show all this in the next video. So, who liked it, put likes. Do not forget to subscribe to the channel. Good luck to all, friends. See you.