New Deltahawk 2-Stroke Diesel V4 Airplane Engine Explained

Machine Engine
3 followers
In this video we take a look at some of the most prominent design features of the Deltahawk DHK180 V4 diesel airplane engine. This video should help understand the design direction the company took and the potential appeal revealed. Is all the hype around the Deltahawk valid, or is it just a fad?
#machine #engine
This engine is an inverted 90 degree v4, two-stroke, diesel, direct drive, turbo and
supercharged fuel injected engine with no electric system. It sure sounds like an odd combination but
this engine is actually quite revolutionary for an airplane engine. I'm of course talking about
the Delta Hawk v4 which has been in development for almost 25 years. But finally, the first
deliveries are scheduled to happen in early 2024. So while it's not breaking news, I find this
engine fascinating because at first glance, not all those characteristics I've mentioned would
seem to work well together. The liquid-cooled v4 engine is 3.3 liters in displacement,
weighing 162 kilograms, that produces 180 horsepower. Delta Hawk claims this engine to be
35 to 40 percent more fuel efficient than an avgas engine, as well as an engine that is incredibly
easy to maintain. So if you're thinking this all sounds too good to be true and is probably just
another fad engine that will never be successful, consider that this engine has already overcome
perhaps the single biggest roadblock that any new aviation engine faces, which is FAA certification.
So let's look at some of the mentioned characteristics in isolation before bringing
it all together for us to make sense what exactly the hype around this Delta Hawk engine is all
about. So first and foremost, the Delta Hawk is a two-stroke engine. And while it's probably not
like any two-stroke you've encountered before, two-stroke engines has several advantages over
four-stroke engines. Since a full revolution of a four-stroke engine is 720 degrees rotation of the
crankshaft, and it generates power on only one of the four strokes it goes through, means only 25%
of its full revolution creates torque, namely the combustion stroke. The other 75% or three strokes
of its revolution consumes torque, being a parasitic load on the engine, of course being the intake
compression and exhaust stroke. A two-stroke engine's full revolution is 360 degrees. 180 degrees is the
piston going all the way down, and then another 180 degrees takes it all the way up. That's a full
revolution. This means that 50% of the full revolution creates torque, and only 50%
consumes torque. In other terms, the two-stroke engine has twice as many power strokes per 360
degrees of crankshaft rotation as a four-stroke engine. Another advantage of the two-stroke engine
is it doesn't have or need any valves, which means it doesn't need a camshaft or any other of the
valve train components needed for the operation of valves. This results in a two-stroke engine not
only being lighter and smaller than a four-stroke, but it is also less complex as it has fewer moving
parts. The valve train system uses some of the torque created by the four-stroke engine to move
the camshaft to open and close the valves. This means the two-stroke engine, which does not have
any of those components, has less friction and less of the torque the engine creates or spent
doing something other than rotating the crankshaft, or in other words, creating power. Combining the
lighter nature of the two-stroke with its ability to create torque on every second stroke, results
in them having very high power-to-weight ratios. But two-stroke engines also have some negatives,
and ironically, the very properties that make them less complex and lighter are also the reason
for its disadvantages. Since the two-stroke engine only has two cycles and no valves, and an internal
combustion engine has four stages, being intake, compression, combustion, and exhaust, it means
these four stages all happen in only two cycles of the engine. This results in the stages overlapping
with each other, meaning none of the four phases are particularly efficient in the two-stroke
engine. Not having any valves also results in less control over air intake and outlet,
affecting efficiency. This also results in very high emissions as well as having bad fuel efficiency.
Another disadvantage of a common petrol two-stroke engine is it usually needs to be overhauled much
more frequently than four-stroke engines. This is partly due to usually being high revving engines,
and partly due to not having dedicated lubrication, and instead the oil is supplied mixed in with the
fuel. The Delta Hawk is however different from a petrol two-stroke engine in some ways. For one,
it doesn't mix oil with the fuel, but are lubricated with internal oil jets via a gear-driven
oil pump supplied by a dry sump system. This is possible because air isn't drawn through the
crankcase like common two-stroke petrol engines, but makes use of loop scavenging. With the fresh
air away from the crankcase and the fuel injected directly into the combustion chamber means that
only oil is in the crankcase, which should make the engine last longer than your typical petrol
two-stroke. But being a two-stroke engine isn't the only thing that sets the Delta Hawk apart
from your usual airplane engine. Diesel engines are of course nothing new, but combining that with
a two-stroke is fairly unusual in aviation. But let's look at the advantages of a diesel engine
over a petrol engine. Of course the engine we are looking at today will most likely be run on
widely available Jet-A or Jet-A1, but note that when I say diesel engine, for the remainder of
video I'm referring to compression ignition engines. One factor that directly affects power
as well as efficiency is compression ratio. In a petrol engine, compression ratio can only go
so high for any certain grade of fuel before engine knock is introduced. The more air is
compressed, the more it heats up. If it gets too compressed and thus too hot, detonation of the
air and fuel mixture can happen too suddenly and prematurely outside of its normal combustion
process. Prolonged knock is bad for internal engine components and can eventually damage it.
And for this reason, petrol engines have a limit on how high compression ratio can go. In a diesel
engine, this problem doesn't exist, because diesel engines aren't spark ignition engines,
but compression ignition engines. Combustion isn't achieved from a spark like petrol engines,
but from the resultant heat of high compression. The more air is compressed, the more the air heats
up and the diesel engine's combustion process starts the moment the fuel is injected directly
into the highly compressed air in the combustion chamber. It thus isn't possible for combustion to
start before fuel is injected into the combustion chamber. This gives us full control over when
combustion will happen, no matter how high the compression ratio and premature combustion isn't
possible. So diesel engines doesn't have any problems with knock and can thus have much
higher compression ratios than petrol engines. And we already know that high compression creates
more torque and improves efficiency. But because diesel engines need to handle that very high
compression ratio, they are built stronger and are thus heavier than petrol engines.
The delta hawk engine is a direct drive engine. This means the propeller is connected to the
crankshaft and spins at the same rpm as the engine. The majority of older petrol airplane
engines are also direct drive. The advantages of a direct drive engine is it doesn't need
the added weight and complexity of a reduction drive. Unfortunately, that's as far as the
advantages of direct drive go. And direct drive has one major disadvantage. And that is because
the propeller is running the same rpm as the crankshaft, effectively limiting the engine's max
rpm. Efficient airplane propellers can't turn much faster than about 2700 rpm and thus direct
drive airplane engines will be limited to a max of around 2700 rpm. Since horsepower is torque
times rpm and a direct drive engine is rpm limited, means there's one fewer way to achieve higher
horsepower. Since rpm is limited, the only other way to increase horsepower is to increase torque,
which is usually achieved by increasing displacement. Yes, there are other things that
contribute to higher horsepower, but this is basically what it comes down to. Modern petrol
engines can run more efficiently with better power-to-weight ratios at quite a bit higher than
2700 rpm, usually closer to 5000 rpm. Running an airplane engine at these higher rpms thus requires
a reduction drive to slow down the propeller speed to less than 2700 rpm. Aside from any reliability
concerns, running at these higher rpms completely offsets the disadvantages of the required
reduction drive, being its increased weight and increased friction. However, this disadvantage of
being rpm limited on a direct drive engine is actually less of a problem on a diesel engine
than it is on a petrol engine. Because diesel engines create more torque than petrol engines,
a diesel can create more horsepower at lower rpm than a modern petrol engine. Let's look at the
this engine being that it's a V4 configuration. A V engine can't achieve perfect primary balance
the way that a boxer achieves it. The boxer 4 achieves perfect balance with the pistons being
180 degrees opposed, meaning the pistons itself cancels out each other's momentum. This is not
only true for primary balance, but also for secondary balance, and thus a boxer is usually
an extremely smooth running engine. On the V engine it isn't possible for the one piston to
cancel out the momentum of the opposing piston, since the pistons aren't actually opposing each
other. This means a V engine needs to cancel out the primary and secondary balance in a different
way to a boxer engine. But if the V has an angle of 90 degrees, it is possible to achieve perfect
primary balance via the crankshaft counterbalance. Now you might think, but isn't that what the
crankshaft counterbalance is there for in the first place? Normally, the main purpose of the
crankshaft counterbalance is to create a smooth running crankshaft assembly by balancing out the
vibrations or momentum caused by the weight of the crank pins and connecting rods. The crankshaft
counterbalance can only cancel out all of the momentum of the pistons at top dead center and
bottom dead center when the crankshaft counterbalance directly opposes the piston. With a piston in any
other position, the crankshaft counterbalance does not oppose the piston and its momentum cannot be
cancelled out. This is why an engine layout like a single piston or inline three, for example, can't
achieve good primary balance with the crankshaft counterbalance weights alone. However, in a 90
degree V engine, it is possible to use the crankshaft counterbalance to cancel out the momentum of both
the crank pin and connecting rod as well as the pistons. When one piston is about halfway down
the cylinder, you can see the crankshaft counterbalance opposing the crank pin and bottom
end of the conrod as per usual. But in this position, you'll also see it opposes the other
piston which is at top dead center. So by using a crankshaft counterbalance of the correct weight,
in a 90 degree V engine, it is possible to achieve perfect primary balance. The disadvantage of this
is the crankshaft counterbalance will be big and heavy, which isn't particularly well suited to a
very high revving engine. But if it's a diesel that is low revving anyway, these big and heavy
crankshaft counterbalances aren't that much of a problem at all. However, another con of the V
engine is secondary balance. Secondary imbalance is caused by the relative shortening and lengthening
of the conrod's vertical length relative to its length in a fully upright position. This changing
in relative length means the piston has to move faster or slower at certain stages of revolution
in the same amount of time. This creates acceleration and deceleration of the piston
as it moves up and down. When the conrod is in a fully upright position, the secondary force
is in an upwards direction. And when the conrod is fully angled, the secondary force is in a
downwards direction. Since the pistons doesn't oppose each other like in a boxer engine, they
can't cancel out each other's secondary imbalance. But it also doesn't stack up like it would in,
for example, an inline four and instead creates a resulting sideways imbalance,
switching from one side to the other. While the V4 does not have great secondary balance,
this imbalance in the 90 degree V is relatively small in magnitude and would not require a
balance shaft to cancel it out. And thus, this tiny imbalance would be acceptable.
Looking at the mentioned characteristics cohesively, they oddly perfectly complement
each other. Diesel engines are very heavy, but making it a two-stroke means it can shed all
the weight of the valve train system and can now be much more competitive in power to weight ratio.
Diesel engines are also particularly well suited for a direct drive system, much more so than any
modern petrol engine, because diesel engines create more torque and doesn't rely on high RPM
to create high horsepower as much as a petrol engine does. Being a diesel, it also benefits
more from turbocharging than a petrol engine since compression ratio does not need to be lowered to
prevent knock. And the only real limitation being the strength of the engine and its internal
components as it needs to withstand that high compression ratio and torque and also remain
reliable. Two-stroke engines usually require more frequent overhauls, but since this is a
low-revving diesel with fuel injection and loop scavenging means it gets dedicated internal
lubrication which should make the engine more durable. What else sets this engine apart?
The company claims this engine has 40% fewer parts than other engines. That would depend,
but that seems very plausible. For one, being a two-stroke engine and not needing a valve train
system alone would much reduce the parts count. This also connects to another aim of the company
to make maintenance very easy and cheap. Not having a valve train makes it simpler to get to
the pistons as an example. The engine also has replaceable cylinder liners and accessories like
coolant pump and oil pump are externally mounted for ease of maintenance. The engine also has no
ignition system which is possible of course because it's a diesel engine and additionally
it has absolutely no electronics, so no FADEC or anything like that. Even the diesel injector is
fully mechanical. Jet A1, which is the fuel the engine will likely be using the most,
is much cheaper than Avgas, but the engine can actually run on a variety of different fuels
as listed on their website. One problem from using diesel in aviation is it has a gel point of only
minus 9.2 degrees Celsius, while Jet A1 has a freezing point of minus 47 degrees Celsius.
Since the engine is designed to run on a variety of different fuels, it has a fuel preheat system
to prevent other diesel types from freezing or gelling. These fuels also has zero lead emissions
as well as less carbon monoxide pollution than petrol engines. Delta Hawk claims brake specific
fuel consumption of 0.38 to 0.4 to create 180 horsepower and 492 newton meters of torque at
2600 rpm. The engine has a max rpm of 2700 as expected of a direct drive engine. Stated fuel
burn is 27.6 liters per hour at 135 horsepower economy cruise and 40.9 liters per hour at 180
horsepower. I mentioned earlier that the engine is both turbo and supercharged, but interestingly
only the turbocharger isn't used during sustained engine run and the twin screw supercharger only
provides starting air compression. Once sufficient rpm is reached, the turbocharger takes over.
The supercharger, however, is reported to be able to supply emergency power in the event of
turbo failure, which would then supply around 50 percent power. One question often asked of new
engines is TBO or time between overall. I couldn't find TBO stated on the website or anywhere else on
the internet, but hopefully it is quite long as the $100,000 price tag for a new engine
might be tough to swallow if it needs to be replaced often.
