Bargue 巴爾格繪畫課程 -16 - Small Lines Arm
影像雜貨志
18粉絲
2025年11月4日
OK, so we're just going to continue working the way we did in the last video
and just continue refining the arm the rest of the way
So, I'm going to kind of work from the area that we were last visiting
and just kind of work my way up to towards the top of the arm
So, let's see here
I'm just going to check a few
I'm seeing that this angle is just a little more that way
Now, I'm still checking all the way through
I'm trying to make sure that where it's going to hit makes sense when I adjust things
What I'm doing right now is we simplified these two shorter lines with one line here
And so now, I have that one line
What I'm doing is I'm going back and making the two angles
The two smaller angles there
And again, try to keep all your lines as straight as possible
You know, because these original plates were done in lithographs
which means that they were printed using a big stone
And then, the original prints were actually much bigger
And then, they've been shrunk down
What happens is that the line quality here is actually quite fat
And sometimes, that makes it look like there's curves
or it makes us tempted to put a curve in
But as much as possible, try to keep everything as linear as you can
You know, some of our former lines
I'm feeling like that angle is really just a little bit more this way
So, now that we're in the refining stage
We can start correcting our errors
We talked about how these two lines in my drawing here look similar in length
But when I look at the original over here
especially if I erase this interfering line
that really, this one is much longer than this one
And so, I need to ask myself a few questions
I know that this line needs to be shorter
And it looks like maybe the angle could be pushed out
just a little bit more this way
So, just don't assume
because you measured very carefully
the first time you put things down
that you didn't make an error
Always assume that it's wrong
until you can prove it to be correct
And whenever there's an error
there's almost always like a few different ways
that you can correct that error
So, you know, here
we knew that this line had to be longer
and this line needed to be shorter
But this line could get shorter by changing the angle of it
Or it could get shorter by just shrinking the angle that's already there
So, there's always a few solutions
And you want to make sure that you find the one
that's going to make everything overall more accurate
So, I'm feeling like this angle here
is going to be coming in just a little bit more
And that already helps me make sure
that that angle or that line here
is longer than this line here
which needs to be shorter
So, I essentially just moved two lines
a very small increment
And I've been able to correct that error
And again, just keeping everything clean
will help a lot
If you make a bad line, make sure you erase it
Don't let your page get really messy
with lots of lines on it
So, I'm making a couple sloppy lines in a row
And sometimes what that means
is that my charcoal is just too dull
And so, if you're making fatter and sloppier lines
get a clean piece of charcoal that's nice and sharp
There's a very subtle curve on this arm here
So, what I kind of need to figure out
is how I'm going to describe
that very subtle curve with straight lines
So, what I'm going to do is break it into two
One going this way
And one going this way
And so, when I look at those angles
I see that it's pushing out slightly
And then in slightly
It needs to be a little higher
So, now I've broken that one line into two
And again, you're still using
the lines that you've drawn before as a baseline
You're just reiterating the ones
that are most useful to you and adjusting them
And again, kind of clearing out
the bits that you don't need
Again, I have a subtle curve here
I'm just going to break it into two lines
Two
Actually, maybe this one
I'll break into three lines
Because it's kind of coming down this way
Two
So, what's happening is this little curve here
And I'm just going to break it up
And my third line was actually already down there
So, we're getting really subtle now
So, it's going to be more and more challenging
to find these breaks
But I did one, two, three
So, those are not big angle changes
We're getting more and more subtle
I'm going to, of course, erase back
the bits that I don't need
Bring this up
Adjust this a little bit
OK
We have just a few more lines in here
So, you'll notice that if I put down a line
that I'm not completely satisfied with
that I will erase it back
And try it a few times until I am
OK
So, we have what's called now
our basic block-in
We have our big idea of what's going on here
And our last stage
before we consider going to the next step
that Bark is showing us
is to just really clean up all of our lines
Make sure everything is as precise as we can be it
And in our next video
we'll talk about some ways
to catch some of our mistakes
before we go on to the next phase
