For my daughter's 9th birthday, the only thing she wanted was a "beachy" loft bed. So you know I had to make it happen. But how do you make a loft bed "beachy" you say? Well we started by coming up with a design list of must-haves. Here's what we came up with: -"Beachy" / Coastal Theme -Mature enough that she will get many years of use -Not damaging to floor / existing trim -Plenty of storage & play area -Electrical for outlets and lights As this list came together, I quickly realized that this wasn't going to be a weekend project. Nevertheless, while this project took longer than expected and cost more than projected, I think we nailed it and I will say that it was well worth it!
For my daughter's ninth birthday,
the only thing that she wanted was this beachy loft bed.
And I think we nailed it.
So in this video, I'm gonna show you all the steps
that it took to give her the dream bed
that she's always wanted.
Let's get started.
Now, when it came to the design of this bed,
I was actually kind of limited on both sides.
We had a closet door on one side,
and then we had the entry door to the bedroom
with a light switch on the other end of the bed.
After getting the design done,
I was able to start cutting down the wood
for the frame of the bed.
Then I could begin assembling the frame of the bed,
which included the false wall
that was going to act as the headboard,
as well as include some nooks and bookcase
on the lower end of the loft bed or below the loft bed,
as well as the front wall
and the wall for the stairs to mount to.
Once I got those frames assembled,
then I could bring them into the room
and find those studs to be able to anchor those in place.
With the frames all up,
then I could focus on the floor of the bed,
and I started by securing a two-by-two against the wall
to all of those wall studs that I found.
Then I mounted some two-by-fours from that two-by-two
to the opposite side of the bed frame,
and that was gonna make sure
that that bed floor was nice and rigid.
Once I got the frames in place,
I was then able to rough in the electrical
for the outlets and the can lights.
Now, for the exterior surface on the wall,
I could've simply gone with some half
or quarter-inch whatever.
However, I needed some rigidity to this
to not only support the stairs on the end,
but also support the railing above it.
And like I said earlier, I'm limited on space,
so we decided to go with three-quarter-inch MDO.
So MDO is essentially plywood
with an exterior surface of MDF.
Then I could start to work on the stairs themselves.
I simply mounted some two-by-twos to the wall
on the end of the loft bed,
as well as the exterior wall for the stairs,
and then tied those all together with two-by-fours
and a couple of two-by-twos up against the wall.
Then I cut down the risers
and installed those with pocket holes and a nailer.
For the interior of the loft bed,
as well as that false wall or the headboard,
whatever you wanna call it,
we went with a seven-and-a-quarter-inch shiplap,
which is just gonna give it that beachy,
coastal-y look that Madison wanted in this loft bed.
When I designed this bed,
I wanted to utilize the space that we had
as well as possible.
So what I did was I created some openings
underneath of the stairs to act as storage boxes.
So I had to build those boxes
and then install them in those openings.
I also did so in the nooks.
There is a bookcase below the loft bed,
as well as a little nook above the headboard
or in the headboard, just so she can store some things.
And I plan on running some electricity,
some outlets in those places
so that she could charge her devices and whatnot.
With all that done,
then we can move on to prepping this entire unit
for primer and paint.
Now, in order to do so,
I needed to fill all of the nail holes
with DAPS Premium Wood Filler.
And this is a great product for this
because it goes on smooth.
It's got that nice white color,
so it's going to cover well as far as the paint goes.
And it fills all the minor imperfections
that sometimes wood filler,
standard wood filler might have trouble doing so.
With all the walls in place,
as well as the little boxes for the nooks,
the windows and the storage unit,
we could then begin to start trimming out
all of those spaces.
I did so with some one by three pre-primed trim,
and it really tied everything in
and really started to come together
as a kind of like a little mini house.
After getting all those nail holes filled,
then we can move on to caulking all the joints into place.
And we did so with DAPS Extreme Stretch.
And as you can imagine,
this stuff stretches very well.
So as the unit kind of moves the loft bed,
people are getting in and out of it,
the joints are going to flex,
and we needed that extra flexibility.
So this is a great product for that.
With all the filler sanded and everything caulked in,
then we can move on to the primer.
Now, all of the bare MDF, it needs to be primed.
So we went with a, just a standard BIN123 primer,
which is going to make sure that we cover all of that MDF
so that it doesn't soak up too much paint.
With everything primed, then we can move on to the painting.
And we went with a higher quality paint,
kind of a scuff-resistant paint
to make sure that this bed as it gets used
and the wear and tear doesn't cause this paint to scuff up
and be hard to maintain.
I wanted to get all the primer and paint on
before we installed the railings
because those are going to be that natural wood,
and we went with red oak for that.
Now, I went ahead and cut down those railings,
and then I counterbored some holes
into that bottom one by two.
So all the railings are made out of one by two red oak,
counterbored some holes in the top of those,
and then mounted them to that plywood with screws,
as well as DAPS Weldwood Instant Wood Adhesive,
which is going to give me a instant
or near instant permanent wood bond
between those two surfaces.
Then I came back and added the vertical pieces
for the railing, as well as the top bar,
and kind of that brought everything together,
mounting those all together with that instant wood adhesive
and some pin nails.
I'm not gonna lie, based on our limitations,
I was worried about how the railing
was going to come together.
I was limited on space there,
so I needed to make that railing as narrow as possible.
However, once it all was put together,
this railing is extremely rigid,
and I think the fact that we turned that corner
and brought it back towards the top of the staircase
really kind of tied everything together
and made sure that that railing wasn't gonna move.
For the steps, we went with red oak as well,
and I just used standard red oak step treads
that you can get at any box store.
However, the step treads actually weren't deep enough,
so I needed to add a piece on the back,
which I did so by cutting down
some of the leftover step tread and gluing that
and clamping it all in place.
We came back and finished those red oak step treads,
as well as the railing and the handrail
that goes up the stairs,
with a wipe-on polyurethane and a satin finish.
I was able to mount those step treads
with a construction adhesive
and then just some pin nails to hold those down in place
as that construction adhesive cured,
and they really fit in there very nicely.
As nicely as they did fit,
there were still some gaps and cracks,
and I did kind of need that
because I didn't want them to scratch up
the painted surfaces as they went into place,
so I came back with a clear caulk,
which actually goes on white but dries clear,
and then we followed up with some paint
to kind of crash into those joints.
Now, the bed was coming together really, really nicely,
and I was excited about how it was coming together.
However, the lower spot below the bed,
the play area, we'll call it,
needed a little bit of pop,
so what we ended up doing
was we kind of started looking for some murals,
and we settled on this sunset mural.
Madison said she wanted a beachy loft bed,
so I thought that this sunset mural
was going to be the perfect way to tie it all together.
I started by tracing out the lines for the sunset mural,
and we used some flexible trim that I had
to be able to get those lines nice and smooth.
Once we got all those lines done,
and then we were able to come back with a bucket
to trace the sun,
then we could move on to the actual painting process.
You all know when it comes to paint,
I leave that to my wife.
I don't have a steady enough hand
for especially this kind of painting,
but she does, and I'm happy to offload that work
to her whenever possible.
As far as the colors go,
we picked a standard color for the sunset
as well as for the water,
and then we just kind of reduced the amount of pigment
that we put into each one of those different paint colors,
and they'll do that for you at the paint store,
and we just got samples of each
because that's all the paint we needed,
and that worked out really well.
Now, if you want more details on the colors we chose
and how to dilute those
and what percentage of the pigment you need in each one,
make sure you head on over to the blog post.
Our link to that is going to be in the description
where you'll find out all the information on that stuff.
The last step in the process
was to come back and install the shelves.
Now, the shelves for the bookcase
were standard red oak plywood
and then trimmed around the top
or around the front of those,
rather with a red oak trim.
I believe that was a half inch
by two and a half inch trim piece.
We did that on the two middle shelves for the bookcase,
and then we went with a red oak piece of plywood
for a divider in between the storage units,
and we trimmed the front of that out with a one by two.
All of those shelves got secured
with inch and a quarter pocket hole screws.
So I hope you guys enjoyed this video.
I couldn't be happier with how it turned out.
It definitely was a lot of work,
however, it's beautiful.
I love it, and I know my daughter Madison loves it as well,
and she will for years to come.
If you haven't hit that subscribe button yet,
make sure you hit that one right there
so you won't miss out on any future videos.
If you want the full plans for this bed,
you can follow that link right there,
and that's gonna take you on over to the website.
Until next time, be safe and happy building.