Build a Modern Kids Treehouse #anawhite (1).mp4

Beautiful Tree House
153 followers
4 Video Views·Jun 20, 2025
We built our kids a modern style treehouse. This was a fun and easy build! Since we built the wall framing in the garage, it went together fast, and minimal ladder work.
This week we're building a modern treehouse.
My kids have been asking for a treehouse for years.
Our oldest daughter is almost a teenager.
I'm scared that she's going to stop asking one of these days.
So this week I'm going to set aside all my other projects and build her a treehouse.
Here's the plan.
We'll screw 2x6's between three strong sturdy trees.
Then we'll build a 2x6 floor and put it on top of the tie-ins.
Then we'll build wall trusses out of 2x6's and 2x4's and bring those up to the platform.
We'll tie it all in with 2x4's and 2x6's.
Add cedar siding.
Put 2x4's on top to create overhangs and support a tin roof.
We found three healthy trees near our house.
Then we took a 2x6 and used lag screws and a level to attach it to the trees.
We repeated to create a triangle between the trees.
Grace and I built the frame here on the foiler trailer and now we're going to put it up there.
We got the basic frame up on top of the treehouse platform, but I didn't add all the joists
because it would have gotten really heavy and hard for me and Grace to do.
So now we're going to slide all the joists up and attach those in place.
Yeah!
The reason that we built this floor frame the way that we did is it gives us something
square to work off of so it's really easy to build a nice square treehouse even if our
trees are irregular.
But I've got to make sure things are square so the way that I do that is I take opposite
diagonals and then I just adjust until they match.
Now for the plywood.
We're just using scraps left over from our workshop build and we just use the plywood
to help square up the platform and then screw it down with screws.
While Jacob worked on the subfloor, I'm going to cross place the platform back to one of
the trees.
So I just used lag screws into the tree and screwed to the base of the platform at a 45
degree.
The 2x4 seemed plenty strong enough but if I could do it again, I'd probably use a 2x6.
This really helps strengthen the platform.
The treehouse platform is all done and we're going to go get the walls.
Alright, it's still raining out so what I'm going to do is assemble the wall trusses right
here in the garage floor.
I used my miter saw to cut the angles out for the wall trusses and then I just laid
everything out on a flat level spot in my garage using 2.5 inch deck screws to attach
everything together.
Once I got one of the wall trusses done, I just used it as a pattern to create the other
three wall trusses.
That way they're all identical.
Then we just hauled the four wall trusses out to the tree fort location and they're
nice and lightweight so we just handed them right up to the platform and started tying
them together with 2x4s and 2x6s in between.
The framing went up in a matter of minutes.
Got the four walls that we pre-built in the garage all stood up and we're going to start
adding the cedar siding to the outside.
So what we're using is cedar fence pickets, they're about $2 a board.
I needed 30 of them so it only cost me about $60.
It's lightweight, it's weather resistant, you don't need to finish it and it smells
really great.
So we're going to start putting it up.
I really like working on this tree house because most, if not all, of the work could be done
from inside.
So notice we never had to use a big extension ladder for any of the exterior work.
Now we're going to add a little deck on the front of the tree house.
So we had some leftover decking boards and we just ran those a little long, chalked a
line and cut everything off.
For the ladder we just took two 2x4s and screwed them level to the front of the deck and we
ran those long.
And then we just added ladder rungs in between the two 2x4s.
To create the railing we cut the top of the ladder boards off with a level and then we
just tied 2x4s into the ends of the ladder and the trees.
A drill, a level and a circular saw are your friends here.
Now we need something to support the tin on the roof and also to create some overhangs
on the sides.
So what we're doing is attaching 2x4s to the top with an overhang of about 6 inches on
each side.
We just screw these right to the wall trusses.
We got tin today and this is the last step.
Jacob and I worked late last night.
There wasn't actually a lot of work to do last night except the kids were crazy and
they were just so excited about the playhouse that we couldn't get them out of it.
So the kids are at school right now and we're going to finish up the tin.
Okay so we got the tree at the back of the playhouse so we're just chopping that out
with some tin snips.
It was a challenge building this project because we're out in the woods so everything had to
be hauled in by an ATV and we have a one year old and we had a whole pack of kids that were
so excited about the treehouse they were really in the way while we were building it.
So we tried to make it fun, somehow we made it happen this week just working on it a couple
hours a night here and there when it wasn't raining but we think it turned out amazing
and it was actually a pretty easy build.
We're super excited to share the plans with you guys because I can't wait to see what
you guys come up with for this plan.
So head on over to my website and grab those plans, build it and share a pic so we can
see how your treehouse turns out.
Thanks so much for watching and we'll see you next week.
