My daughter wanted a new bed and couldn't find anything she liked at IKEA or other furniture store so she decided to design and build one (with some help from Grandpa) and we built this together! Here's the cuts we made and the tools we used:
Twin Bed Dimensions and cuts (Double-check and adjust measurements if you are building a larger bed):
2 - 2x4x8’ - (Select/Premium - 1.5” x 3.5”) Trimmed to 3” in width on the table saw and cut to 36” in length for the Headboard and 16” in length for the foot-board 3 - 5/4x6x8’ - (Select Pine - 1” x 5.5”) Cut 2 at 38” in length for the headboard and foot-board, and 2 at 78” in length for along the side/length of the bed. 1 - 5/4x4x8 - (Select Pine - 1” x 3.5”) Cut 2 at 38” for the headboard (or use more cross bars if you prefer). 2 - 2x2x8’ - (Furring Strips - 1.5” x 1.5”) Cut to 78”. These will mount to your 5/4”x5.5”x78” side-boards and will support the cross-bracing that will support the mattress. Add another one down the center and support with a 2x2 at the base of the footboard and headboard IF you are building a full, queen or king bed. 5 - 1x3x8’ - (Furring Strips - .75’ x 2.5”) Cut to 11 strips at 39.75” (or close to that) in length for the cross/bar/slats that will support the mattress 16-18 - Pine 5/16” wood plugs
Of course you can adjust these measurements if you desire to build your bed a different size. Just measure twice and cut once!
We recommend using SELECT Pine or other premium cut lumber that is straight. It’s really nice to start with straight wood. You could build this out of Cedar, Pine, Oak, Ash… whatever you can find. Happy Building!
Screws and Fasteners: #10 x 3.5” Drywall Screws (for attaching the headboard/footboard to the side boards) https://amzn.to/3bg4QWk #6 x 2” Drywall Screws (for attaching the side supports and cross bars) https://amzn.to/3i0BJrr
Hi there, welcome back to the channel.
Today I'm here with my father-in-law, Tim, again.
Say hi, Tim.
Hi, Tim.
And my daughter, my middle daughter, Amelia, which many of you haven't met yet.
Say hi, Amelia.
Hi, Amelia.
Yes.
We have another DIY project for you today.
Do it yourself.
And, um, you've been wanting a new bed for a while.
Yes.
Yeah.
Uh, and you have a twin bed, right?
I do.
So we're going to build a twin mattress frame, headboard and footboard.
You look very particular in your design.
Not, uh, not picky, but particular.
I wasn't finding anything I liked.
So I thought, you know what?
I've got resources, might as well use them.
Let's just build one.
Yeah.
Tim used to be an architect.
So we got these architectural drawings of this bed right there.
They're pretty fancy.
And today we're going to cut the wood and put together this bed, right?
Let's do it.
Now you have to go get some allergy shots, right?
I do.
I have to peace out.
So I'm gonna let you guys do the hard work, cut all the wood and
I'll be back for the fun part.
All right.
So we're going to get this wood cut up.
We also will put a list of all our supplies and all the materials we
use in the belt bed build, uh, in the description below, let's get building.
Perfect.
As we said, we started with a great set of plans and then we headed over to our
local home improvement store and picked out the wood we chose select pine five
quarter by six for the frame around the whole bed and four for the
cross bars across the headboard.
We used select two by fours for the headboard and footboard along the edges.
We then trim the two by fours down to three inches in width to square them
off and then cut them at 36 inches in length for the headboard and 16
inches in length for the footboard.
We've got a 36 inch, two 36 inch pieces and two 16 inch pieces for
the footboard and for the headboard.
Next, we're going to cut the cross pieces for the headboard and the footboard for
the headboard.
We're going to use two, three and a half inch pieces by five quarter, and
we need to cut those at 38 inches.
I've made the measurement of the mattress itself, and then I added an
inch and a half on each side for blankets and sheets to be able to tuck down around.
So with a queen bed, you'd need to take the width of your queen mattress, add
three inches for an inch and a half on each side, and that would give you the
length that you would need for this.
We're going to be cutting the side pieces here at those 78 inches.
What we're going to do is we're going to set this 14 and three quarters from the
bottom, just like the plan shows right here.
And then we want to put in three screws to hold it in place one inch down from
the top and from the up from the bottom.
We marked and positioned the screws so that the headboard cross pieces would
be flush with the side boards.
You could mount those cross boards in the center if you'd prefer.
We're going to use these plugs to plug the holes when we're done.
So what we need to do is to pre-drill down about a quarter of an inch, and
this is exactly the same size as the plugs.
So we'll do that first, and then we'll drill the hole all the way through for
the longer screws so that they'll hold together really well.
After getting everything cut to size and the holes pre-drilled, we gave everything
a good sand, even sanding along the edges where the headboard and footboard cross
pieces met the headboard and footboard frames.
So the seams where they met would be nice and smooth.
We also hit the head and footboard edge boards with the belt sander to take off
the sharp edges and make them smooth to the touch.
We then put a bead of glue along the seams before fastening the pieces together.
We'll put information about the fasteners we used in the description below.
First, we're just going to attach the side boards.
I think we need to actually put the two-by-twos on side boards first, get that
going, and then we can get it all together.
So we cut our two-by-two boards the same length as our side boards, put a bead of
glue along them, and then fastened them on the inside of the side board with two
inch fasteners.
Once the two-by-twos were fastened to the side boards, we put a bead of glue along
them and then fastened them to the head and footboards with three and a half inch
screws through our pre-drilled holes.
We left the screws fastening the headboard to the rest of the bed flush so that they'd
be easily removable, making the bed much easier to transport.
We then cut 11 one-by-three furring strips to roughly 39 and three-quarter inches in
length that would support the weight of our mattress.
We spaced them out evenly, marked them on the two-by-twos, and then fastened them to
the two inch screws.
After everything was assembled, we gave the entire bed a good sanding with 220 grit
sandpaper.
We rounded off the edge boards of the head and footboard slightly to prevent any rough
or sharp edges.
After everything was sanded, we put just a dab of glue on our pine buttons and covered
up all of our pre-drilled holes.
So you've had quite a busy week.
It looks like, yeah, we got the bed done.
We got the old one out of here.
We got the new one in here.
It really looks good.
Yeah.
What do you think?
I love it.
I couldn't be happier with it.
Of course, it's a bed of my own design, so I'm really pleased with the result.
I thought Grandpa designed it.
I'm the ideas person.
He's the execution.
And then you didn't want any stain.
You wanted just the natural wood color.
I love the look of just the varnished pine.
I think that it's super classy.
So we just sanded the whole bed down and then varnished the whole bed with satin
polyurethane.
We did three coats of that in between.
We just touched it with some 220 grit sandpaper, and I am so pleased with the
result.
It's fine.
It's classy.
It's simple.
And the way that Grandpa designed it with a little bit wider than a twin mattress
gives you enough room for your comforter and you can kind of tuck it down in there
and it looks really good.
Definitely.
Well, we hope this video inspires you to maybe take on a project at home and you
can build obviously, if you want to make this a full bed or a queen bed or a king
bed, you'd have to have you obviously would have to change the measurements.
Also, on those designs, I would probably recommend reinforcing the center line
correct with two by two on either the on the headboard and on the footboard within
a two by two brace running down the whole middle.
So you have another support for your cross braces if you're going to go wider than
a twin bed.
Other than that, it's a pretty simple build.
I think we we did it in about three hours with really two and a half of us working on
it. We're going to leave a list of all the measurements, all the sizes and all the
tools we used in the description below.
As always, we'd ask if you really would help us out by just clicking the like button
that really helps the YouTube algorithm and subscribe to the channel, share it,
participate in the comments.
We do read and respond to most of the comments.
So thanks for watching and we'll see you again soon.
Thanks for building with us.