Automating the Worlds Most Advanced Engineered Wood Product!
Comments are disabled for this video.
Ferris Engineered Wood is a small family-owned business that's been operating in the San
Anne Canyon in Oregon for over 100 years. We make one of the world's most advanced
engineered wood product, which is a mass plywood panel. That mass plywood panel is used in
high-rise and commercial construction throughout the United States. The environmental attributes
of wood products are second to none. They're a naturally carbon sequestering solar product
that we can utilize to make one of the most advanced wood products on the planet.
The mass plywood panel is our company's proprietary take on a mass timber product.
Many people are familiar with a cross-seminated timber panel, which is a lumber-based mass timber
panel used as a substitute for concrete and steel in high-rise construction. Our panel happens to
be veneer-based, so we peel a log, kind of like you're unrolling a roll of toilet paper,
into one-eighth inch thick pieces of veneer that are a lot like paper. And we assemble those pieces
of paper back together until they are a one-inch thick lamella. We use those lamellas then to
construct a larger panel that can be up to 12 feet wide and 48 feet long and up to 12 inches thick,
substituting for typically floors and roofs in commercial construction.
We were attempting to design a facility in order to create large panels out of smaller pieces of
wood. In order to do that, we were cutting a joint into our panel. It's called a scarf joint.
Unfortunately, the equipment that we were using initially didn't have the tolerances or the
consistency that we were looking for. We turned to Pretech to help us design a system with FANUC
robots in order to create the consistency and quality of product that we were really looking for.
We are an ASI for FANUC Robotics, and we service a multitude of industries,
from the wood products you see here all the way to aerospace. The issue was surrounding these
mass plywood panels and how do you get them to come together with a scarf joint.
One of the problems was the consistency of that joint and how do we make that joint come together.
And one of the ways to do that was by using a robot. In this particular case,
we'd selected the R2000-210L. Everything is based on how well that joint comes together
and holds. If the joint is not well put together, it can come apart. Having them come apart will
ruin a big panel. The end of arm tool, it'll come down and it'll grab the plywood panel that's
going to be scarfed. It'll use vacuum to pick that up, but you can't just use vacuum when you're
presenting that to a scarf tool because if you did, the tool might just tear the panel right off.
You have a device that will square that plywood up, which is vital for that scarf joint because
you have to have the same distance of your joint on each side and in the center,
then it clamps it down, holds it, and then it can present it to that tool. And then it can turn it
around and do it to the same tool. And one of the objects of using the same tool, of course, is that
you have a matched joint. You're using the same cutter head to be able to have that wood together.
Each load that comes out of the scarf line, we measure the scarf just to make sure that
the measurements are correct. It's an eight and a quarter inch scarf. You've got four and a 16th
on one side, four and a 16th on the other with that hook in the middle. Kind of just bonds it
really well together. We're using the FANUC robot to really control the scarf cutting process to
make sure that we're within tolerances. Additionally, it's a lot less labor, a lot
less problem for our employees, a lot less manual labor for our employees. It's an easier process
for them to manage. The robots have totally changed my job here. It used to be a lot more
physical where I would be exhausted and a lot of running around and checking things.
But now it's more fun. It's interesting how well the robots perform in their programming.
It frees me up to load the line and look at other things that I can be helpful doing.
If you have somebody who's new to industry, it can be scary. It's like, what is this teach pendant?
Oh my gosh, what am I going to do? You don't have to be afraid. Just need a little training and it's
available through the FANUC network. So our technicians can do training, FANUC can do training,
and it's been a real good benefit. I didn't have any experience with any kind of robotics.
I was a little scared, honestly, when they said, hey, you got to learn that.
But it was really easy. It was simple, the program was simple, and the robot responds and does exactly
what you tell it to do, what it's supposed to do. There are many environmental benefits to our
product when compared to concrete and steel in construction. It takes far less embodied energy
to produce our product than it does with concrete and steel. We're eminently recyclable. We sequester
carbon in the cells of our products that we produce. If people are concerned about climate
change, you should be building with mass number products like our mass biopanel. We're looking at
technology and robotics in particular as a way to support the innovation that our industry needs
to survive and our company in particular to survive for another hundred years.

