Inventor 2022 Lesson 18 Drawing Setting up dimensioning styles

Inventions and Inventors
25 followers
2 Video Views·May 21, 2025
Comments are disabled for this video.
In today's tutorial, we will learn how to write size and edit the size in Inventor
To write size, we have some commands to write size
The most common command is the dimension command
Writing size is very simple
We have learned a lot in AutoCAD
In Inventor, it's even simpler
We just need to click two sides
Then click one point to get the size
Or click two points
First point, second point
Then you will get the size of those two points
However, we see that
If we write the size like this
The size number as well as the accuracy of the size is not correct
But if we edit each size one by one
For example, this size 100
To edit it
Click the mouse button
100 to 0, 0
Now I have to adjust its accuracy
Is 0
That is, it is 100
Click OK
This way of editing is very manual
And if we have to edit each size one by one
It will take a lot of time
And that's not the right way
So before writing the size
We should install some types of writing size
Then we write the size
When we write 1 or 2 sizes
We will click on that size
And in this Annotate section
We will notice
In this format area
We see the type of size we are using
Dimension ISO
Then we go to Manage
Go to Style Editor
And to install as well as to create some types of writing sizes
Dimension ISO
And we see there are many types of writing sizes
In there
The type that we use most
And it is the default
Every time we write a size
It is written this way
Default ISO
I just clicked on the number 100 here
To format
It means default ISO
Then we should check again
As well as select the parameters to install
For this type of writing
And we can also create some other types of writing sizes
That we want
Then we will click on default ISO
And on the right hand side
There will be a lot of choices
In this course
We will learn
What are these choices
And we need to understand these choices
To be effective in the process of writing sizes
As well as size adjustment
The first item is Units
It is the unit of measurement
The unit of measurement here is the unit of measurement for the specified size
Is the unit of measurement for the specified size
And the next item is
Alternate Units
It is also the unit of measurement
But the unit of measurement for the specified size
When you learn this math
You have to be able to distinguish
What is the specified size and the specified size
For example
Phi 100
Plus minus 0.01 for example
Then 100 is the specified size
And minus 0.1 is the specified size
So this Unit
Is only set
For the specified size
But
Liner
Is the unit of length
The length
The length here we set as millimeters
It is the Vietnamese standard
We specify that
The size of the specified unit is millimeters
The middle part
The origin and the component
Will be separated by the comma symbol
Which is the comma
The size is
Phi 100.1 for example
Because the symbol
Separates the origin and the component
We use the comma symbol
If we don't set the period
It will be wrong with the standard
With the length
We will also set the accuracy for it
Here we see
Because we are setting
Precision
2.12
That is, the accuracy is
2 digits after the comma symbol
So
It only appears
9.00 or 100.00
So we should
Leave it as 0
It will only appear
The original part
Or make a circle to the original part
Of course there will be cases like
0 is 100.5 for example
We will have another way to deal with it
We will talk about that later
And the most reasonable
We should leave it as 0
This is the length
And the original size
Is the angular format
Angular format
We will leave it as
The speed of the thread
And the accuracy
Here we can
Leave it as
The speed of the thread for example
Or according to the calculation
According to the drawing that we can set
This unit is
Set for the size
The unit includes
Measurement unit
The distance between the original part and the part
And the accuracy
Next we go to
Measurement unit for
Size
Sorry
Measurement unit for
Size
We will have
About
Unit
We will also set it as
Millimeter
And if we set it wrong
The unit of
Size is also
Same as
The size of
The original size
The distance is also
Equal
With accuracy
We can leave it as
2.12
If it is 2.12, it will be
0.01
I will explain more about this
If we set it as 0
It will be round
And only the original part
If we set it as 1.1
It will be plus minus 0.71
If we set it as
2.12
It will be 0.01
If we set it as
3.123
It will be 0.001
The most common is
2 units
We will set it as
2.12
It is for units
The next unit is
Display
Display unit
Includes
The lines
Or
The rules
About the distance
Between the parts
In a line
This part
We will find out more
It is also very easy
Because we will look at the object here
The distance of B
Is equal to how much
B is the distance between
The line of the object to the line of the size
We usually set it as 0
This part we will find out
The next part is
Text
It is the part of the size
The part of the size
We have talked about
In science
Is to set and write letters
Set and write letters
This part of text
We have
Select the font for
The font size
This is primary text style
Select the font for the font size
Here we have
A lot of fonts
To make it convenient, we can choose
Note text
We should check
Note text
How is it set
If we are sure
We choose the text here
If we are not sure
We can check
By clicking
Edit text style
Z
To save the options
We just set
It will go to
Text
Note text
We check again
We set the standard
Vietnam 7284
The height of the letter is 2.5
For the letter i
That's right
If we don't want to edit anything
We will go back
Back
Next is tyrant text style
Tyrant text style
We should set
It is the same as the font
Tyrant text style
If we don't
We should not choose the font
It is different from the font
We should set a font
To be unified
In this case
Tyrant text style
Use the font
Note text
Tyrant text style
Use the font
To be unified
And
We have another option
Size
Tyrant text style
Size
We should set it
Smaller
Size
Note text
We set it 2.5
We can set it 1.8
1.8
It will look better
Orientation
The position of the size
Aligner
Align
and some choices here
with a diagonal size like this
we will definitely use this type
with a straight line like this
we will choose the correct one
which is the third option
the last option
These are some of the choices that we will choose
Diameter
is the position of the number of dimensions
compared to the size line in the case of
for
the diameter of the diameter
and the diameter for radius is the diameter of the diameter
we will
quickly
like this, we will choose
the third option
This one, depending on the case, we can choose either the first or the second
If we want
the diameter to be horizontal, we choose the first option
Similarly, in the case of a radius
we choose
it to be horizontal
The next option is a tolerance
which is
Does this form follow the zoom size or not?
We are setting the default
we are not following the zoom size
and if we follow the zoom size
we will choose more options here
Some types of zoom size that we
often encounter, such as
Symmetric zoom size
We can set it here
Upper here is assuming that the plus is not equal to 1
and minus is not equal to 1, for example
Plus minus is not equal to 1, it will appear as plus minus is not equal to 1
This is the zoom size for
Angle
We will leave it as it is
We can set any number for these
we can edit it
The type of size is also often encountered
The type of zoom size is also often encountered
Deviation
That is the silent type
Silent above is upper
Silent below is lower
Upper is plus, not equal to 1
Lower is minus, not equal to 2, for example
We can always put it here
This section is
mainly introduced
It depends on the application of the drawing
that we will have the settings
or we do not
use
Zoom size, we set it as default
Default, we will set it as default, that is
not included
Zoom size
Not included zoom size
Options
Options are some options
Some options in
When we write the size
Arrowhead placement
This is the position selection for us to set
The arrow
We will go through some options
For example, for
Size
Maybe the arrowhead is inside
Of the two lines
Or the arrowhead is outside
Of the two lines
In any case, it is correct
It's just an application
In any case
We will set it as the first case
Next, with the angle like this
The arrowhead is inside
The two lines
Or outside the two lines
This case is the same, for the circle
The arrowhead is inside the circle or outside the circle
And for the size of the radius
The arrowhead is inside or outside
Let me say it again
These are also depending on the case
Depending on the case that we will choose
However, we need to know that
In this case
What is it like and what is it like in the other case
The next options include
Extension lines
Is the choice
There is a hidden path
Size line or not
Here is
If there is no arrowhead
That is, it is not hidden
And if we use the arrowhead, it will hide
The extension line
Above
And if we click here, it will
Hide the extension line below
Of course
Rarely happens in cases like this
We have to hide the extension line, so we should determine
No, not hidden
For other sizes, too
We can hide one way
It can be hidden above
Or hide the path below
It's up to us to choose
Radius dimensions
It is
Set the size line for the radius
With the radius, if we put it
In the first option
If you put it in the first option
There will be no size line
And if we choose the second option, there will be a size line
For the radius
And this option will be used more
The next two options
It is the shape of
Size line
In the case of radius
The first case is no
Arrowhead
Straight
And the second case is it has
The thickness
Of the size line
Next is
Diameter dimensions
That is the choice
For the size for a
Diameter
For the diameter
In the first option, we see
The line appears
Show Diameter Dimensions
Phi
Symbol
Phi
Surely we should choose to display the phi
In this case, it does not display the phi
In front of the number in front
For the diameter
The next two options are
There is a display
Size line
Connect to the center
We will
Will choose to have a display
And some other options
Less important, I will not say
Then I click save and close
Save and close
So when I just changed the settings
Of
I just changed the settings
Of
The size line is Default Iso
Immediately the number 100 and
The number 9 will be
Changed
Now we will write one more time
From here to here
It is exactly
This is the size from here
And the default iso setting
Default iso
Is
We are not included with the size
For example, now we want to create a new type of size
It has a size for example
Create a new type of size and it has a size for example
Then we will
Go back to this manager
Style editor
We will click on new to create a new type
New size
This size has a size so I will name it zs
Is the size
OK
In this size, the options will be the same as the default
But in this tolerance
I will add more
Here I will add more
Symmetric style
And here I will set
Plus minus 0.02
Click save and close
Now I will write the size for it
And annotate and write the size
Suppose this is size 15
Is the default iso style
Now I will write the size
I will choose the wrong zoom style
Then I write the size from here
There
We will see that
At this time it will follow the zoom size
It will follow the zoom size
And if we assume
We want to fix the plus minus 0.02
Suppose there are many
There are many sizes that we want to write
This is the type of ht27
This ht27 is the default iso
And now I will write
The style is for
Zoom size for example
I write again
It will be ht27 plus minus 0.02
So
In a drawing that has a lot of zoom size
We can't
Create many sizes
Which corresponds to the value of the zoom size
We should only create one style like that
And we can edit it
If this is ht27 plus minus 0.02, we click delete
Click delete and we will fix the value here
Plus 0.02 is now plus 0.01
Click save
And click ok
There it will become plus 0.01
So we don't necessarily have to
Create one more style
Zoom size
Corresponds and has the value of plus minus 0.01
I will write from here for example
It will appear as phi 2.0
And this phi is because we set it
Inside of the setting
Size
And now the size will be much simpler
It will be much simpler
We want to write the size for the point
We will click on 2 points
In short, in today's tutorial, we will create
Types of sizes
And
Use the dimension command to write the size
To create the types of sizes as well as edit
Set the size
We will
Go to manager and styles editor
In this dimension
Usually
The default size is default
So we need to
Pay more attention to this default ISO style
And
You have to know the choices inside
Among them, the important choices
Such as the dimension of the dimension of the dimension of the dimension of the dimension
Zoom size
Especially this text part
We have to choose the font
This is the note text
Note text
Which is in the
Note text
We have said
And some other options
So when we have the size
The thing
We write the size, it's much simpler
And very fast
Convenient in the process of writing the size
