Installing the JessEm Router Lift on my Table Saw - Router Lift - Woodworking

Sparky Deal
160 followers
Hey this is Joseph with Gerber Design and in this video today I want to show you how I installed
this Jessom Tool Company router lift on the wing of my table saw. The first thing that you're going
to want to do is you're going to want to rip some strips of plywood down. I'm ripping mine
to about four inches because that leaves a good amount of space for my router base to ride on
without it tilting or falling. I centered the lift in the middle of my table saw and added
X-Fasten double-sided tape to all the plywood to secure it to the table. I see a lot of people
using this X-Fasten tape with their CNC's so I thought I would pick some up and give it a try.
It does work really great. It is very strong and as you'll see when I rip these off later,
it does rip some of the plywood off with it so just be cautious on whatever it is you're
adhering it to because you could chance maybe ripping up a little bit of it if you are sticking
it to plywood. When you're framing out the lift you're going to want to make sure that you're
doing everything you can to keep that lift as snug as possible. A suggestion I have is to make sure
that longer piece you have on the side you adhere that first and then do the rest after. Now that I
have the frame all in place I'm going to grab my router and then I'm going to grab a quarter inch
shank templating bit. This bit I'm using is from Whiteside and I will make sure and link that below.
Now in order to set the depth on my plunge router I'm going to plunge the bit all the way down to
the table and then I'm going to add a 10 millimeter domino in between the depth gauge and the stop.
The router plate just happens to be the same thickness as a 10 millimeter domino. Then once
you get started on there you're going to want to make sure you take smaller passes. It's a lot
easier on your router and your router bits when you do that. I probably took three to four passes
maybe five when I was doing this. Once I had got the initial plunge for the outside of the frame
I realized that I needed to remove some more material so I took a piece of three quarter
inch plywood that I had and I used that for my router to ride on so I could remove some more
material inwards without my router falling over. Once I had the majority of the material removed I
cut out the remainder with my jigsaw. I probably should have removed these plywood pieces for the
frame when I was doing this but I was just a little nervous that the depth wasn't deep enough
and I did not want to re-add all of those strips back just to make sure that it was at the proper
depth. And now I'm not going to show this because nobody wants to watch my mistakes but it took me
a few passes with the jigsaw to get that hole to the correct width. And here is where I was
thinking and realized that maybe you should set your depth just a little bit deeper because you
have all these set screws that will take care of any discrepancies you have with the depth of it.
Obviously don't go too deep but you probably could have erred on the side of a little bit deeper than
too shallow. I have the Dewalt three and a half inch router motor but this lift is compatible with
any three and a half inch motor. All you have to do is loosen an allen screw and it will release
the holding mechanism and then drop it in place and re-tighten. Now I want to make sure that the
lift is securely fastened to the table so I'm going to drill out the holes for the four screws
that they sent. These are four quarter 20 screws and I'm not sure if mine was just missing something
but it did not come with any of the nuts for these screws. Luckily I just happened to have some
quarter 20s laying around so if you do order this know you're probably going to need some quarter 20s.
The allen wrench they give you with this is kind of comically long and unnecessary so I took it
over to my bench vise and used my angle grinder on it and decided to make it a little bit shorter
and also save that piece of allen wrench for my drill so now I can make the lift go up and down
a little bit faster. I thought this was a great idea until I actually started using the lift and
realized that I only used the drill bit attachment part to raise it and lower it when I was changing
the bit. Another cool suggestion I have get some magnets. I attach these magnets to the legs of my
table saw so that way anytime I need any of my accessories they are within reach. Then I had a
little space on my tool wall and added the last couple accessories. A really nice thing about
having a lift on your table saw is I can use my table saw fence as a point of reference. You can't
really tell in this video but basically I'm just cutting these grooves and using my table saw to
get them lined up perfectly on each side. Eventually down the road I'm sure I will pick up a fence with
some dust collection on it but for right now this is working great. Thank you so much for watching
this video. I hope it was helpful for you in showing you how to install a router lift on your
table saw wing. Let me know in the comments what router lift you are using and what you like or
dislike about it. I hope that you subscribe and we'll see you on the next video.
