Inventor 2022 Bài 14 Drawing Các lệnh xuất bản vẽ từ 3D sang 2D

Inventions and Inventors
25 followers
2 Video Views·May 17, 2025
Comments are disabled for this video.
In this lesson, we will learn some rules about drawing in Inventor
Before drawing, we will check for the last time
whether our 3D detail is completely accurate
in terms of structure and size
Because when we draw, if the 3D detail is wrong,
our drawing will also be wrong
However, in the process of drawing,
if we discover errors in the shape or size of the details,
we can go back to the 3D detail to fix it
Immediately, the 2D drawing will change
First, before drawing, we have to choose the right direction
This is the vertical direction of the 3D detail
This is the horizontal direction
We choose the vertical direction
This is the horizontal direction
If we choose like that,
it will be more convenient to display the drawing
After we choose the vertical direction,
we will click on the button next to the rectangle
We will click on Set current view as front
to choose this direction as the vertical direction
I will click on Front
This is the vertical direction
This is the horizontal direction
We have to choose again
We will choose again
This direction is the vertical direction
I will click on Set current view as front
to choose this direction as the vertical direction
I will click on Set current view as front
This is the horizontal direction
This is the work we set at the beginning
It will appear more during the drawing
After that, we will click on New
In the drawing environment,
we have created a standard drawing
No name, no drawing, as required
Then we click Create
Before creating a drawing,
we need to save and name it
If we haven't saved it yet,
when we use commands to create a 2D model,
we will also need to save the drawing
Then we will be able to create from 3D to 2D
First, we select the paper
Is the paper correct?
If the paper is incorrect,
we will click on the paper
Right click, select Edit sheet
Then we can choose the paper we want
We can also choose
Project is vertical or Landscape is horizontal
In this case,
I will use A3 paper is horizontal
so I will not change the paper
The first command is Base
Base is to create basic shapes
We know that there are 6 basic shapes
These are the shapes that are perpendicular
to the faces of the shapes
Usually, we are familiar with
3 shapes, such as vertical, horizontal, and horizontal
Here I will give 3 basic shapes first
Vertical shape is a triangle to the right
Horizontal shape is a rectangle to the left
Horizontal shape is a rectangle to the right
and horizontal shape is a rectangle to the left
We can also create other shapes
For example, when I move it to a perpendicular direction
I will have a rectangle shape
If I move it up,
there is no space in this area
So I can move it up a little
After that, I will have the image from the bottom up
After that, I will click OK to finish the command
Before clicking OK to finish the command, I can also choose the scale in the scale area
In there, the scale 1-1 is the original scale
And if we want to draw a bigger object, we will choose the big circle scale
For example, 2-1
And if I want to draw a smaller object, I will choose the 1-2 scale
I will choose the 1-1 scale
We can change the scale later, so it doesn't matter
To adjust the position, I will click on the rectangle
After that, I will move it down
This rectangle is the main rectangle
So the movement of the rectangle will affect the position of the other objects
And if I change the scale of the rectangle, the other objects will also change
I will move the rectangle from the bottom up to a more reasonable position
The side rectangle to a more reasonable position
On the left side of the model, you will see a lot of performance images
Each performance image is marked by the word view
When I point to view 1, we immediately notice that in the performance image, there is a red dot
This is view 1
View 2 is the side rectangle, it appears in the red rectangle
View 3 is the horizontal rectangle
View 5 is the rectangle from the bottom up
And view 4 is the vertical rectangle
We can also name these performances to make it more convenient during the drawing process
And display a complete drawing according to the Vietnamese standard
I will click the mouse button on the rectangle
In view 1, I can change its name to the rectangle
Click OK
Immediately, view 1 will turn into a rectangle
Click, do the same, click the mouse button on the rectangle
Change its name to the rectangle
Of course, this is not important
It just makes us more convenient in the process of creating a technical drawing
View from below
Here I will change the name to the side rectangle
We notice that there is a button here
The button is connected to the vertical rectangle
Connected to the main rectangle
And we will not be able to change the ratio of this rectangle
Because we can only do the opposite
That is, the vertical rectangle changes the ratio
The rest of the performances will change
We can't do the opposite
We can't automatically change the ratio of the side rectangle
Because this button is hidden
If we want to change, we have to remove this property
But because the performance on the main rectangle must follow the ratio
Normally, we will still have this property
Then the rectangle
Do the same
Rectangle
You can change this rectangle and choose a reasonable ratio
For example, 2.1
Or 1.2
Or 1.1
Depending on the calculation, we set the appropriate ratio
Click OK
Here I am putting 5 performances
We do the same to put other performances
We can also delete the performances
For example, the rectangle from below
If not necessary, we will click on it
Click Delete
Click OK to delete it
The side rectangle is the same
If we feel it is not necessary, we can delete it
Or right from the beginning
We only show the rectangle, the rectangle and the rectangle
No need to show the side rectangle and the rectangle from below
We select it and click Delete to delete it
Then click OK
Now we click on the rectangle
We can change its position
Or change its ratio
This ratio is 2.1 for example
Click OK
When changing its ratio, the rectangle will also change
It is connected to the rectangle
We click Delete on the rectangle
We need to pay attention to the following options
The first option is the option that appears on the networks
Currently, I am using the first option
Style
This is the option to display the networks
You will see that these performances already exist on the networks
The second icon in the Style section
is Hide and Lie Remove
In this section, this option will hide the networks
If we click OK, we will see that the networks are hidden
We do the same
The third option is the option to play football
Here we need to note that when the option is activated, it will be pressed
Here I see that there are two options being pressed at the same time
Hide the network and play football
Click OK
So our performance is both hidden and played football
In the Style section, at first we will use the function to hide the network and not play football
We will turn off the play football function
Then we will turn on the Hide and Lie function
Click OK
Here to display the commands more clearly, I will use the 1-1 ratio
Because if the ratio is 2-1, it will be too big
Here I will use the 1-1 ratio
Click OK
And I will delete the mouse cursor
Click OK
So the first command, the Base command
It is to convert 3D objects into 2D flat objects
If we delete the horizontal object, and I click OK
The horizontal object will also be deleted
So they are connected to each other
We will do it again
Base command
In this Base command, this file is the link to the 3D object
We will convert the 3D object into 2D objects
Of course, if we turn on the 3D object first
And then we open the 2D table
The machine will understand that we want to convert the 3D object into 2D objects
And the link of the 3D object will appear for us
And if we are opening a lot of 3D objects
And the computer does not understand that we want to convert the 3D object into 2D objects
We can also select the link in this table
We can select the link to open the 3D object
It is correct
Here I will use the rectangle and the rectangle
Click OK
Continue
The second command is the project command
This command will create basic shapes
Create basic shapes from existing shapes
To use this project command
At least we need to have an existing shape on the drawing board
We click on it
For example, here I have a rectangle
I want to draw a rectangle, for example
I will use the project command
I click on the rectangle
And I move it to the right
This is like we are drawing from left to right
We draw from left to right
Click on the right mouse button
Select create
It will create a rectangle
We can do the same
We use the project command
We click on the rectangle
It is like above
We will have a rectangle from below
Click on create
We can also click on the rectangle
Click on the rectangle
And put it in the position we want
To create other shapes
This project command will create shapes
When there is an existing shape on the drawing board
Now I will delete these shapes
Click ok to delete it
The next command is auxiliary
It is to create vertical shapes
It has an angle
It is perpendicular to any plane
It has an angle
It is perpendicular to any plane
This command is used when there are perpendicular faces
And complex shapes
If we only use basic shapes
Angle to the perpendicular faces
We will not be able to see the whole structure
It is in the position of the perpendicular face
We will have to use the auxiliary direction
It will be more convenient
In this detail, we will see that there is a perpendicular face
In this perpendicular face, we will also see an oval structure
In these details, it has a perpendicular face
If we only use basic shapes
For example, the shape of the table
If we only use basic shapes
We will see that the shape will be distorted into ellipse shapes
And it will not be able to clearly show its shape
In that case, we should use the auxiliary direction command
We will click on that command
In this case, we will click on the ellipse
And we will choose this edge
This edge represents the perpendicular face
When we choose this edge
The direction of the ellipse will be square with this perpendicular face
Then we move the mouse to another position
Put it out
The shape of this perpendicular face will be clearly shown
I will Ctrl-Z to return to the previous step
We do it again
Auxiliary
We will click on the ellipse
Here we have some options
View, Identifier
This is the name for that direction
Its default is A
We can change the name
In addition, we can change the ratio of that direction
As well as the Base command
We can have 3 options
Hide
Show the network
In this case, we hide the network
And finally, the ball
In this case, I will set A
The scale is still 1
According to the default of the machine
Click OK
We do it again
We choose the perpendicular face
Then click on the edge
The direction of the ellipse will be square with that perpendicular face
Click on
In this case, we only use the details that have complex structures such as the perpendicular face
And on that perpendicular face, there will be structures such as gaps, holes, etc.
We just use
I will delete
The next command is the section command
This section command creates a cut
Create a cut
The cut here can be a simple cut
It only has one cut surface
Or you can create complex cuts
You can create complex cuts
To do it, we will click on the section command
Suppose I want to cut
I want to cut at this position
Of course, in this case, we will not cut like that
Just an example
I will click on the perpendicular face
Then
Our job is to draw
Draw the cut surface
Please note that
When we execute the command, the command will appear
On the left
At the bottom of the screen
If we forget any steps
We will read the command again
At this position
It is to determine the starting point of the section line
Another way is to draw
Draw the cut surface
Here I will draw the cut surface through the hole
The first point is here
The second point is here
Right click
Continue
It is similar to the right
Similar to the right
Before setting up
Before setting up, we pay attention to some options
Such as
View Identifier
We set the name for that cut
Scale is the ratio
Usually the ratio is the same as the ratio
We choose on this rectangle
We will set up
There
Will be
The display image is
BB
This BB is the cut
Cut
With the position of the cut surface here is
At this position
And the sign
Its name is BB
We can also
Click on the word BB11
Let's fix it for it to be reasonable
We will see the text format box appears
This view is
B
This view is B
And this scale is the ratio
We don't want this ratio to show up
We will
Leave it
We will leave it and click OK
And in case we want
Leave the word BB
We will choose this one and leave it
It will also be lost
Here I will show the word BB
And I will leave the ratio 1 to 1
We do the same for other cuts
In this case, I will
For example, I cut at the position of the rectangle
For example
Then I will click on the rectangle
Then I will have to draw a cut surface
Actually, I draw a cut surface from here
This is just an example
In this case, we don't need to draw
The cut at this position
Click on the right mouse button to choose continue
There
Immediately, the machine will name it C
And similarly, we will
Go to the right or left
If we go to the right
The direction will be from left to right
And if we go to the left
Immediately, the direction will be changed
We will click on the mouse
This is an example of drawing a simple cut
That is, there is only one cut surface
The next example is related to the section command
I will make a complex cut
That is, the cut has at least two cut surfaces
For this detail
This detail will have two types of holes
One type is a smooth hole like this
And the other type is a concave hole like this
To see the structure of these two types of holes
It is best to use a cut surface
From two cut surfaces
The first cut surface will go through this concave hole
To see the structure of this concave hole
And then the second cut surface is through the center of this concave hole
So we need a cut surface
To see the structure of these two types of holes
I will delete this shape
I will use the section command
Then click on this example
Next, I will draw the first cut surface
From here to the center
Then draw the second cut surface
Go through the center of the hole
Note that when we draw
If there are blue dots
It is correct that we have caught the correct point
Go through the center of the hole
Click delete
Then right click
Select continue
Right click select continue
We hide to the left
Hide to the left
We click delete
So this is an example of a complex cut shape
This is called a concave cut shape
We have two cut surfaces at the same point
This section command can create simple or complex cut surfaces
Depending on how we draw
Draw a straight line to represent the position of the cut surface
We will have a simple or complex cut shape
According to our wishes
Next we will execute the command
Detail
Draw a rectangle
Or call it a rectangle
To make it consistent with the drawing
I will delete the performance images
And cut images
A, B and C, C
Detail is drawing a rectangle
When will we use this command
In the case that it is at a position of the detail
The shape is too small
Can not see the shape of the detail
Can not see its shape
And because it is small
It is very difficult to display its size
In that case
We will enlarge those positions
Can be enlarged at any rate
And then we will see more clearly
Execute the command Detail
Then we want to draw a position
We will click on the performance image that holds that position
I will click on the rectangle
Because in this case
For example, I want to enlarge the position of this hole
On the left hand side of the detail
I will click on the rectangle
D is its name
We can change its name to A
And here I set the ratio to 2 on 1
That is, I enlarge it twice
Click on the rectangle
Select the center point of the fence
Click on the rectangle to determine the center of the circle
Then we move the rectangle to determine the size of the circle
We will click on the rectangle again
To determine the size of the circle
In addition, we can also choose the shape of the line
The line at the position we want to enlarge
Is it a circle or a square?
And the limit between the enlarged part and the unenlarged part
By the shape of the different lines
For example, I use this line
And I click on the rectangle
I will move it to a new position
Click on the rectangle
We will see that this is the part of the bullet hole
In this area, it has been enlarged twice
And here we will pay attention to the circle
The limit between the enlarged part and the unenlarged part
It will have a curve
Because we have set it in the section command
I will do it again
In the detail command
I will do it again
If I want to enlarge the position of this hole
I will click on the rectangle
This is just an example
In reality, we will not do that
I will name it
I just named it A, now I named it B
And the ratio is 2 to 1
We usually use a circle
Actually, we rarely use a square
And in this case, I will use lines
In the form of zigzag
To distinguish the enlarged part and the unenlarged part
I will click on the rectangle to determine the center
And then click on the rectangle again
I will click on the rectangle again to draw a circle
And then click on the rectangle again to draw a circle
Now I will show you B
The enlarged part of B
It has been enlarged twice
And this limit line
It is used by zigzag lines
This is completely due to our installation
We can also click on it
We have to rename it
Because this is B, we can rename it to C
2 to 1, we don't want
We can give it 5 to 1
Click OK
These are the changes after we have done it
