Martin Tenor Sax Restoration 1- Cool Tool Tuesday- band instrument repair, Ferree's Tools, Wes Lee

Restore all old things
33 followers
9 Video Views·May 13, 2025
Good afternoon friends. Thanks for stopping by the house of tone today. My name is Wes Lee.
I'm a banishment repair technician. I started a YouTube channel to show what my life is like in
the trades. I've got a fun one today. I'm going to show you a couple of new tools as well. So this
is on a Tuesday when I'm filming this. I may get this released today on a Tuesday. So we're going
to have a cool tool Tuesday. All right let's jump in. All right we've got this really awesome
tenor saxophone. Look at the wonderful condition that this lacquer is in. I mean it's just amazing.
You start to see some problems. Really bad bell crush. But wait there's more. Flip it over to
the lowers. Can you see those lower stack keys? These are way bent. Terrible body dent here.
And look tone hole is unsoldered. At least one. So it looks like something fell across here and
really took this out. So I'm going to show you some new tools. Because this body is in such
great shape we're going to get into here using a special tool. And I've got a big beefy tool
that we're going to use here. Let's jump over to the vise. So today for this project we're going to
use this really stout rod. This is an inch and a quarter diameter. It's not designed for doing
any kind of rebound work. It's going to keep strong and solid while we press against it. This is what
I'm going to use for the bell section. This is an N74A out of the Faries catalog. And as always I
like to use lanolin as my. So let's get this bell taken care of. These were such cool horns.
Had a lot of respect when they were made and got to give just as much respect as far as repair.
This rod allows me to really put a lot of pressure down without worrying that it's
bending on me. I'm not chasing the rod. I've got a lot of this out. I'm going to switch to a
a little bit of a smaller ball. Be a little punchier. I've got a little bit of a ridge over
here. I'm feeling where it's out of round. It's round here and it's round here. So I want to make
this feel of the same contour. The larger your dent ball the more surface area. So you can
use that logic. If you use a smaller dent ball you can get more
more punchy. You just have to control it more. Miraculously the body of this did not get bent.
Somehow the brace and the body. It's very lucky. Very very lucky. So now I'm flipping to the
tapered side. Coming in. I'm just going after all the little stuff that I also see. Super important
under the logo because you get under that U. Okay now we're going to work down to the to the G
and work that script back. You can see the low spots pop out. I'm pulling it back up to the G.
When you follow the light and you grab a dent and you just kind of twist that dent
staying under the bottom most portion of it and allowing it to come back up to the
light line. I'm just hitting it very very small and what I like about this rod is that it just
doesn't it lets me put all that I want to put into it and it just doesn't move. It's very stable.
Sometimes accidents happen. This one happened in shipping. So I'm using a chasing hammer
a dent hammer. It should be known as a chasing hammer and I'm chasing out the high spots.
So I've got little creases from where the deep dent was. I've got a few little ridges and I want
to chase them down flat and then I can raise the low spots to match and should be virtually without
scar. Just working along that line working the light line. Okay I should be able just to knock
it back out now. What I'm doing is I'm coming in and I'm actually just tracing every dent line,
every crease line that was put in it. I'm under it and and riding it back out.
So just every little fold that was in the metal
being very careful just to stay on top of it under the worst part of the dent deepest part
small little movements. It actually may come up a little high. That'll be okay because I
use this chasing hammer to blend it all back in. I'm very happy with that around the logo.
Now we're going to go back to a larger ball and blend all of it back together.
So now we're just going to do a final bit of blending bringing all the ridges and
roundness together. Looks like it was never there. Our bell came out very nice.
I can hardly tell there was any damage. You can see a little bit where the case
or whatever struck and folded that down. We're going to turn our attention to the stacks.
Turn my light on. You can see where the tone hole is pulled away there
and just really bad in the body. This kit is the N92 Sack Snake Kit.
So the take off on an old tool. So you have a long rod that chucks in your vise,
a flexible metal cable that comes with that's threaded on the end. This locks. This draws back.
So when you take your threads off, the kit comes with six barrel-shaped balls
and two round-shaped balls. This matches that taper on the end of the tool and they thread in
onto the holder. You draw the cable back and it tucks down on the end and you tighten it in place.
So you can go through the bell and this goes down the body tube. So you don't have,
you can have a morsed out dent rod without having to use a slotted ball. Let's put it to use.
Cable comes down. The cable comes out the end. We're going to thread it on.
Curtis Furee really did a good job in bringing this tool back
and updating it. Keep that in there. You draw it back. You pull it. Get that funk.
You lock it in place and now you can see that we're, there's the tone hole and we're inside.
And the reason that I like this tool, especially for this job,
I want it to be like we were never there. And I have to be very careful
around these solder tone holes. I want to push it up enough, but I don't want to push it too far.
Go ahead and grab that E-flat post. I'm going to push that back up.
Okay. All right. At this point, I'm going to go ahead and take off the chromatic F sharp
key so that I can get at this area a little bit better. Now it's really important that
work slowly and precise to bring the body tube back to round. When you're doing this, go slow.
Remember what you're working with. It's a big long tube with a bunch of holes in it.
It's going to be real easy for it to get away from you. Exercise a lot of control.
Bringing that tone hole just right back to where it wants to go. All right. Now we're
going to start working this seam down here. Okay. I've got a couple of little high spots.
I want to go ahead and tap those. I want to soften this dent area. I'm hollow tapping. I'm
not tapping on that ball. I'm not trying to. I want to blend this in. Coming back up. Lost our
audio here. So we're just going to overdub it. So here I'm showing that I'm going to go ahead
and disassemble the lower stack and the bell keys so that I can solder the tone hole. After I've
gotten things disassembled, I find another dent in the body around where the bell key guard was.
So we're going to have to take care of that. Right now we're going to focus on getting things
ready for solder. It's important to get the tone hole nice and clean on both sides. So I'm taking
my scribe and cleaning off the old solder work. Once I've got everything cleaned up, I'm going
to take a piece of binding wire and wrap around the tone hole to keep it in place while I get
things tack soldered in. A number five tip on the Smith LittleTorch allows me to get in
very tightly to get good solder and heat penetration around the tone hole. Unfortunately,
the old lacquer was so brittle and tired that it did burn in a couple of spots. So I'll have
some cleanup work to do there and then I'll have to try to blend that tone hole riser
back in with the rest. Now I'm going to reinstall the bell key guard so that I can have proper
alignment and I'm going to use that to my advantage when I do the dent removal under the
last brace to hold the key guard in place. Now we're going to thread the ball back on the sack
snake to get it fed back through the body and we can finish doing our dent work. Here's where
coming on the back side of the body tube to remove the dent that's under the brace for the
bell key guard and you can see it pop back into place right there with no stress and everything
falls back into alignment. That's exactly what we want. Now we're going to turn our attention
back to the body tube on the front side and come under our tone hole in question and just remove
the last of the scars from the dent that was in the body and this one's going to come out great
and you can see where I'm going to have to touch up some finish there on the tone hole itself
but I believe we're going to be able to blend all that in pretty well and now we're getting down
to it. I have almost all of the light lines blended back in. I've got things really back
where I want it to go. My tone hole is re-established. Everything is looking
really like I want it to look. Here I'm using my high heat gun and what I'm doing is I'm warming
the brass and by doing that it starts changing colors. You can see it's taking on more of the
golden appearance so it looks a lot more vintagey air quotes and so it's going to blend in a lot
better. You can really see here from this pulled back shot how nicely it's how nicely it's looking
and blending in. I tested being able to solder with the high heat gun and I could not get it
hot enough to make my solder flow the way that I wanted to so I did not feel that it was a good
choice for doing the solder work at that tone hole and now I'm going to seal it up with renaissance
wax. A viewer actually commented and said that I needed to try it and I did and I really like this
stuff. There's a reason that it goes on museum quality pieces. It really looks nice. It does a
great job sealing in the patina of the instrument and so you can see our color match that I got out
of that is really doggone good. I'm pretty pleased with that and the the way that the scarring is
so very minimal from what we started with. I believe the client is really going to be happy with this.
Well all right thanks everybody for joining. How about that? Turned out really nice. Are those
some cool new tools or what? Thanks to Faries Tools for sending me that prototype to check out
and to share with you guys. I'll put the links down in the description for the part numbers so
you can contact them get some of these cool tools for yourself. Amazing stuff. Having the right tools
allows you to do just incredible work. I hope you were able to pick up some tips and tricks on doing
metal work and fine metal work and figure out some ways to work around. It was a little unfortunate
that I burned the lacquer around that tone hole. I'd really tried not to but that old brittle
lacquer was just it just is what it is. So there's a little mark. Yeah it'll be fine. The horn's going
to play great. We'll finish the job on another date. Got to do the key work. Got to level the
tone holes. Customer requested the Selmer style brown boosted resonators so that's what we'll go
with. So we still have to do all that. So there'll be another episode with this really cool saxophone
and of course we'll play it for you so you can hear what it sounds like. I'm interested in hearing
what it sounds like myself. It's a beautiful piece. Thanks very much for following along. I
really appreciate it. Thanks for stopping by the House of Tone. We'll see you next time around.
This is Wes Lee signing out.
