Welcome bersers. Today I'm going to show
you how to do this unbelievably cheap
method to glue up bows that only cost
about $6 kind of, but it's really easy
to do. Let's jump into
[Music]
it. Basically ready to glue up now.
riser. Two short fiberglass, two short
bamboo, one long glass, one long bamboo.
Form setup's behind me. Gonna time lapse
this because if I could glue on my
hands, I don't like to touch the camera.
Don't have any videographers, so that's
the best way to whatever. But basically,
what I do is I put glue on it. I put it
over
here.
Yeah. Okay, fine. I'll tell you the
process. two-part epoxy, EA40. I place
it on a heat strip to act as a warmer.
The glue or the epoxy becomes more
spreadable when it's hot. You want to
protect the form from the glue. So,
adding a little bit of shrink wrap or
plastic
wrap will create a nice
barrier. That way, the form will be
reusable. Next, shop towel and some
poison.
This will clean the fiberglass. You can
look how dirty that is. That's going to
allow better adhesion and a stronger
glue joint. I'll clean every single
part, the fiberglass and bamboo and the
riser. Frog tape. You should use some
frog tape on the back of your fiberglass
to keep the glue from sticking. The frog
tape that's $15 a roll is the only one
you should use because it's the only one
that comes off easily. I'm doing a glue
up right now and I'll be back after
it. Mix the epoxy. Once you mix it, you
have a pot time. That's the amount of
time before it starts to set up. EA40
pot time is dependent on how hot it is.
The hotter it is, the quicker it sets
up. But also, if it's really warm, it is
easier to apply. So, it's like a
positive and a negative. Easy to apply,
but it sets up quicker. A little harder
to apply. sets up
slower. Okay, new set of gloves on. This
is what we look like right now. All the
pieces are up. I failed to mention that
I marked the center of the bamboo, the
fiberglass, and the riser. And then the
form has the center marked as well. That
way everything can stay in a line.
First, we want to do some saran wrap.
Issue with this is if you pull it
tight, it will start to slide the riser
in the opposite direction.
And then I push it back the other way by
doing this fade
out. Yeah, just like that. And then
we're going to go down the whole
thing. This is not
clamping. This is protection from
glue. Next is some pressure strips.
These will keep everything even so that
as I add pressure and clamp this down,
it evenly spreads it over the entire
limb. But the pressure strips will be
followed by a heat strip. This is just a
silicone strip that heats up to very hot
temperature to cure the epoxy. And
actually we are going
to reverse that heat strip then pressure
strip.
Now, I built this form with these holes
here so that I could throw a large C
clamp on to do pressure points.
Extremely strong here and on the fade
outs. Light pressure at
first. Then I build these an extremely
tough 1/4in rubber with the same
material that we have for the backing.
What this does is allows us to throw a
clamp right here. And it's going to bend
evenly and distribute the pressure over
the fade out so that we get a perfect
glue up every single time without using
those fire hoses that drive me
crazy. So, I'm only slowly tightening it
down. And then I'm going to start on
this side. That way, we don't shift the
center of the handle. Bunch of squeeze
out. Better to have more squeeze out
than none at all. And then we can
tighten these down, moving between the
clamps to make sure nothing slides. My
clamping method of choice today is
rubber bands. Take the rubber band,
start up at the riser, hook it
on, boom. I'll put like a hundred of
those suckers on, and it does a
phenomenal job. There is, however, one
potential area of failure when using
rubber bands. But have you ever seen one
of those videos where they tie like
rubber bands around a watermelon and
they do they continue to do it until the
watermelon explodes? Well, that provides
a ton of pressure. So on these fade
outs, you want to just overkill because
that's the only time where the material
is bending stiffer. And if you do a
heavy draw bow, then the material could
be so stiff that the bands couldn't bend
them. But in this case, there's no
problem. I threw a bunch of them on
there. We're good to go. Also, the other
concern you may have, get the lighting a
little better, is that the heat strips
are going to be in contact with the
rubber bands, making the rubber um less
elastic as they get hotter and hotter.
And that's exactly why I put the
pressure strip on top. And from the
three bows I've done before this with
this method, the bands had enough
elasticity at least to give a really
good glue up. Even though you can tell
in some of the spots that touched the
heat strip um there they did stretch out
in that area, but the rest of the band
kept pulling it down that it was fine
and they didn't break. That's it for
today. If you want to see me finish out
this bow, uh don't really subscribe, but
uh just search Kramer Ammons on YouTube
because that's my name, but subscribing
won't help you see anything. You can if
you want to give me more social
currency, but besides that, we'll see
you on the next video.