My Favourite 10 DIY Tips & Tricks

The Next Fixit
86 followers
7 Video Views·May 4, 2025
"""#daily tips#diy#clean&organize#decoration&finishing#""
Comments are disabled for this video.
This week I'm going to show you my top 10 DIY tips and tricks,
the sort of things that I use all the time and are genuinely useful for doing
DIY around the home. Unlike those DIY hacks you see on the internet,
which are stupid and dangerous.
You're never too old to learn. And I must say,
I've been really lucky over the years to pick up lots of tips and tricks,
watching professionals and tradesmen work.
And I always find it fascinating that just when you think you know everything
about a subject, there's always something else that you can learn.
So today's my top 10 tips and tricks.
And although I'm sure you would have seen some of these before,
that's probably going to be different for different people.
And I know there's one or two things in there that I guarantee you haven't seen
before.
So let's start with a little bit of measuring and the humble tape measure and
measuring from the end of a bit of timber with this wobbly thing,
which we all know what it's for.
And it's easy to measure from a fixed end like this.
When it comes to measuring from a line or a screw head or something on a flat
plane, this slidey bit really does get in the way.
And it means that you can end up with something that's not quite as accurate as
it should be, which isn't any good if you want an accurate measurement.
So something I learned on a surveying course many years ago is rather than
trying to measure with this wobbly bit here, just come in to an even number.
I would say a hundred millimetres or maybe four inches if you're working in
that and then put that on the line,
which means that you can actually fix it really accurately.
Then you can measure or mark the other end.
But you do have to remember to add that hundred millimetres back in or four
inches or whatever you're going to use just as a double check.
When I use this method, I must say the last thing I just do is very,
very roughly put the slidey thing on the end and just double check that I've got
the right measurement,
because if you forget to take off that bit that you've added in to start with,
you're going to be miles out. Right.
Number two, measuring an internal dimension.
And this could be within a cabinet or a box or within a window frame,
for instance, if you're trying to measure for a blind accurately.
And traditionally we all put the tape measure in one end and measure the best we
can in the other,
which may give you a measurement to within plus or minus one or two millimetres.
But if you're measuring, let's say for blinds, for instance,
you really want to get it as accurate as possible.
Or if you're trying to get a bit of timber to fit snugly in these,
you really want to be millimetre perfect.
So the best way of measuring something like this,
like an internal is to do it in two halves and I'll show you.
So the first half, just measure a round number.
I'm going to pick 300 millimetres and just put a mark here.
Although this is a carpenter's pencil,
I've sharpened it to a fairly good point.
And then secondly, we can measure from this point up to that mark,
which I'm getting as 267.
So that's 300 plus 267.
So that makes 567.
So to double check,
we can do it the traditional way and just roughly do it.
So I would say that that is 565.
So I'd have been maybe two millimetres out,
which wouldn't have been the end of the world if I was measuring for blinds.
But if I'm trying to cut a piece of timber snugly for this gap,
I'd have maybe cut it two millimetres short to start with.
It does mean you do have to mark the piece.
And if you're working with like a windowsill where you don't want to put a mark,
then just get a bit of painter's tape, put it on the piece and mark the painter's tape.
Then you can take it off. Job done.
So the scenario is we have to drill a pilot hole in exactly the right place
to accept a screw.
And I'm just using a hinge here as an example.
Very easy if you got a self-centring bit.
But most people don't have self-centring bits.
So traditionally, the best way of doing it is putting it in place
and getting a very fine pen or pencil.
We're going to aim at this middle one here.
Mark in a circle.
And that's exactly where we want to drill our pilot hole.
But, you know, as usual, things aren't always as easy as they look.
And quite often you can start drilling a hole and it just goes off centre.
Let me just give you an example.
If I aim here.
So I've just gone one, maybe two millimetres into this,
and it's clear that I'm not on centre.
The grain has maybe pushed me to one side.
And however hard I tried to hit the centre, it just didn't work.
But fear not, there's a solution.
And it's fairly easy.
All you do before you drill too far is angle your drill bit at the centre
and drill a little bit deeper.
And then with it running, just bring it straight
and it should come back to central.
So by aiming the drill bit into the centre at an angle,
drilling further in and then straightening up, being careful
not to break the drill bit, we've managed to persuade that hole to be centred.
So when we put our hinge back on,
everything is looking rather nice.
So we've got our traditional string line that we can use for 101 things,
either in the workshop or outside construction, gardening or whatever.
And we need to keep it nice and tight and tie it off
on whatever pin you're working on.
Now, one thing I used to do was sort of double it over
and end up doing a couple of sort of knots like this, which is OK
until you have to take the thing off.
Then it all starts getting a bit messy.
So let's just set this up again.
Pull this nice and tight.
As I wind this round, I can actually wind it on top of what I've already done.
It definitely helps.
But you can't just leave it like that, else the things are going to fall apart.
So the trick is with the string line itself,
you bring this up and over the existing line
and now you can let go of this.
And this is still really tight.
And this isn't going anywhere because this tight line is holding it tight.
And the best thing about this is once you finish with it,
it comes off really easily.
All you need to do is pop that over
and then this just comes off like a charm.
And it doesn't matter what size line or stake you use.
This could be a line in the garden and a stake that you've got
while you're setting out some pathway or whatever.
You just pull that over and it still works just like that.
This is an excellent little tip that works perfectly and saves a lot of effort.
So when you finish painting, either between coats or for the day,
wrap up your roller and tray in a plastic bag,
and this will stop it drying out and saves you having to clean it
at the end of each day.
In the same way, brushes can be wrapped up in plastic
and will quite happily last days without drying out.
I'm now covered in paint,
so I'm going to clean up using one of these ultra grime wipes.
They're not sponsoring me at all.
I just think that they work incredibly well
and remove any paint, grease or dirt effortlessly.
Somehow they've got a rough side and a smooth side.
And if you ever wonder how I clean my tools after getting them
so dirty in the garden, well, now, you know,
I would highly recommend these wipes and they last for ages.
I'll put an Amazon link to them in the description
if you're interested in having a look.
Fitting your own blinds is a very common DIY job,
and using blinds rather than curtains is a very cost effective way
of fitting out a house, especially when you've got your first one
and you're struggling to pay the mortgage.
I've done a video all about how to fit blinds.
I'll put a link to in the description below,
and I've got a couple of top tips all about when you have to cut these down.
Blinds like these come in standard widths, maybe 600, 900, 1200.
And then you cut them down to suit the size of your opening.
This one started at 600 and I took maybe 100 mil off
to make it fit the window that it's currently working on.
So my top two tips for blinds are rather than trying to work out
how much fabric you need, just work out what gap you have
and compare that to the blind that you've bought.
So if you have a 500 millimeter gap and you bought a 600 millimeter wide blind,
you just have to take off 100 millimeters of material.
You don't have to then worry about how wide the material is
because you've got these plastic bits at each end.
So all you need to do is work out what you need to take off
rather than what you want to keep, and it will work out exactly.
My second tip is that there's two ways of taking off this material.
If you saw my video, one way of doing it is by laying out the blind,
cutting with a pair of scissors, and this way creates a really clean edge
and is probably the best quality way of doing it.
But there is another way of doing it,
which was recommended by a few viewers when that video went out.
And I've tried it this way and it does actually work.
Let me grab an off cut and I'll show you.
So let's say I've worked out how much I need to take off
and that comes to, let's say, 75 millimeters.
So rather than working out how much fabric I need left,
all I'm going to do is mark 75 millimeters on here.
I'm going to leave it rolled up
and I'm going to leave the aluminum center in
and any bars that are used with it.
And all I'm going to do with this is cut it on the mitre saw.
So, yes, you heard me right.
I'm going to cut it on the mitre saw here, just like a piece of timber.
And it's not the cleanest of cuts.
You do get some frayed edges.
But what I found is you don't get that many.
And the ones you do get are fairly easily tidied up
using a pair of scissors afterwards.
But what you do get is an incredibly quick way of cutting down your blind
and very accurate. It's millimeter accurate.
You don't even need dust extraction.
I make sure the blade is running at its highest RPM
before I start the cut, and I take it fairly slowly
as I go through both the fabric
and the aluminum center bar all at the same time.
Any frayed edges I trim with scissors, and although this doesn't give
a perfect result in terms of fabric, it's quite difficult to see once it's up.
And it does ensure that the blind edge is straight by cutting it this way.
So this next little tip I actually put to use a couple of videos ago
when I put the gates on the fence out the back,
but I didn't have time in the video to actually explain it.
And this time, rather than making sure that our drill holes
are exactly in the middle,
I'm actually using a strategy on purpose to offset them slightly
to be able to adjust things a bit like this hinge that I've got here.
Let me show you what I mean.
So the first thing I'm going to do is to draw a fine outline
exactly where I want it around the perimeter.
And then I'm going to mark out two holes,
one at the top, one at the bottom to fix my hinge to.
A bit of a pilot hole.
And this is exactly what happened off camera when I fitted my gates.
But actually, one of the holes was off center and I just didn't spot it.
Which means that when you actually screw it in.
So I don't know if you can see there,
but the whole thing has shifted about a millimeter
or a millimeter and a half to the right because I've got these countersink
type screws here and because the hole is off center,
it then and that final turn pushes the whole hinge off center as well.
But there is a way of getting it back.
And that is to use the two holes that you haven't drilled yet
strategically to bring it back.
Let me show you what I mean.
So this has moved in this direction.
So if I actually drill this hole off center in this direction,
back off that screw and then tighten this one up,
I can actually persuade it to come towards me.
So there's a pilot hole off center towards me.
If I just unloosen this, then I can actually put this one in.
And in the last turn or two.
It will come back to me.
So you may see now that actually the hinge has gone too far to the left.
I can actually see my line.
But with a hole on the right and a hole on the left,
now I can actually adjust this left and right by one or two millimeters,
depending on which screw I tighten first and how much I tighten it.
So if we want it back in the middle, just back this off,
tighten this one slightly, it will move back.
Maybe a little bit more.
There we go.
And then I can tighten this one.
And then if I tighten both together, that isn't going to move
because the friction now between the hinge and the post is such
that it's not going to move left and right.
I can actually tighten those screws up.
And if I have a quick look with my torch.
Now, that is perfectly centered for those of us
that use circular saws guided by a straight edge.
You quite often need to know the distance from the edge of the base plate
to the blade to essentially offset the straight edge on purpose
to cut in the right place.
So to do that accurately, rather than trying to measure with a tape measure,
set up some scrap timber and make a very short cut,
which you can then measure, which is easier and more accurate.
Twenty nine.
So once you've done this, as long as you don't change the type of blade,
the measurements will never change.
So you can record them somewhere easy to find.
Twenty nine and one or two.
More and more people these days are putting up pictures and prints.
So the tops align exactly, which isn't necessarily the easiest thing to do,
because they all seem to have different lengths, wires at the back,
which means the hooks have to be in different places for the tops to align
exactly. And there's an easy way of doing it.
And it involves, first of all, putting up a print.
I'm using the wall here, but maybe the best thing to do
is to use a piece of timber.
And they're just marking a line on the surface at the top.
And now I'm going to do exactly the same with my second print,
which has a completely different length string.
Level it there and put a mark.
And now what we can do is measure the distance between both the tops
of the prints, and that's the difference in the string.
And if I start at 100, like I like to do, that is 158.
So taking off the 100, that's 58 millimeters between these two.
So if I want this one to be exactly level as the first,
I have to put this 58 millimeters higher than this one.
That is perfect.
And the very last tip, if you're still using traditional fixings
into plasterboard, which I'm not, I'm converted, I'm using these claw fixings
rather than using the masonry bit to drill through your plasterboard,
which is essentially just cardboard and very light plaster.
Try using a brad pointed bit, which cuts a lot cleaner hole,
which you'll appreciate when you have to fix it at some later date.
And that goes in really tidy.
I hope you enjoyed these tips and tricks.
I think there was 12 or 13 in the end.
So there's two or three extra for free.
Remember, Patreon, subscribe, all that sort of stuff.
And I will see you next time.
